Dewalt DHS790AT2 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DHS790AT2 manuals!
Problems with Dewalt DHS790AT2?
Ask a Question
Free Dewalt DHS790AT2 manuals!
Problems with Dewalt DHS790AT2?
Ask a Question
Popular Dewalt DHS790AT2 Manual Pages
Instruction Manual - Page 3
... safer at all safety warnings, instructions, illustrations and specifications provided with the switch is in property damage. d) Store idle power tools out of the reach of parts and any other condition that have the power tool repaired before connecting to operate the power tool. English
Definitions: Safety Guidelines
This instruction manual uses the following safety alert...
Instruction Manual - Page 4
...service ... supported....replacement parts...FOLLOW ALL WIRING CODES and recommended electrical...setting, make a connection from either hand closer than 6" (152 mm) from one workpiece at high speeds.
• BE SURE all charging instructions... motor... Service...and installed ...support round material such as the lower guard to the instructions...repair person using length stops, the cut , causing the blade to...
Instruction Manual - Page 5
...is free from ... DeWALT FLEXVOLT BATTERIES OR WITH THE DeWALT ...CORDED POWER SUPPLY. Only connect the power supply cord to operation. Check to hearing loss. Severe personal injury may cause personal injury.
• SECURE THE MACHINE TO A STABLE SUPPORTING...other injury. Replace cracked or... PART ..." POSITION. Clogged motor air slots can cause...
• NEVER STAND ON TOOL. Direct...
Instruction Manual - Page 6
... power or a 120 VAC 60Hz generator. When the power supply is used with this manual for DeWALT 120V Max* FLEXVOLT cordless tools. Before using the DeWALT corded power supply. Do not modify the battery pack in explosive atmospheres, such as no user serviceable parts inside the power supply. ON UPPER GUARD: PROPERLY SECURE BRACKET WITH BOTH SCREWS BEFORE...
Instruction Manual - Page 7
...) rating as a 20V Max* battery.
When the level of the charge left . Provide fresh air. TRANSPORTATION WARNING: Fire hazard. SHIPPING THE DeWALT FLEXVOLT™ BATTERY The DeWALT FLEXVOLT™ battery has two modes... in cooperation with DeWALT and other battery users, has established the program in carry-on airplanes in the United States and Canada to the service center for recycling....
Instruction Manual - Page 8
... authorized service center
when service or repair is fully... of injury, charge only DeWALT rechargeable battery packs. The... Gauge for Cord Sets
Volts
Total Length ... it on standard 120V household electrical
power....can be illuminated during this manual. Do not attempt to ... battery pack are specifically designed to work together...• Pull by displaying a problem pack or charger blink pattern....
Instruction Manual - Page 9
... authorized service center...parts. In addition to the battery pack.
2. If the battery pack does not charge properly: a. If the charger indicates a problem, take the tool, battery pack and charger to your miter saw blade May include: 1 DeWALT Corded power supply 2 60V batteries 1 Dual port charger In bag: 1 Blade wrench 1 Material clamp 1 Dustbag 1 Instruction manual
Specifications...
Instruction Manual - Page 10
... by the convenient lifting handle, as a workbench, strong table or DeWALT miter saw from one place to its various parts. The handle is
FIG. 5
pulled down pin (Q, Fig. 4).... Hex wrench
G. Lock down pin when carrying the saw stand. Clamp hole
I H G F
Your saw is capable of cutting the following once a special setup procedure is followed. CUTLINE™ worklight
J. The section...
Instruction Manual - Page 12
... adjustment screw (AL) to set a crown stop allows the depth...support or moved to any adjustments, cleaning, repairing, or removing/installing attachments or accessories. Have the tool serviced... feet to Instructions for applications ...manually raise the guard. AN
Always be sure the blade has stopped before continuing use both.) Always mount your own safety by an authorized DeWALT service...
Instruction Manual - Page 14
....1 (CAN/CSA Z94.3). To set before making any adjustments, cleaning, repairing, or removing/installing attachments or accessories. In order that... kerf plates as close to provide maximum workpiece support, without interfering with sawdust. BEVEL STOP 45º RIGHT...0° bevel to clear the guide grooves. WARNING: Always use a brush or some low pressure air to the table.
...
Instruction Manual - Page 16
...adjustments, cleaning, repairing, or removing/installing attachments or ...SUPPORT LONG PIECES. An unbalanced load may occur. Always clamp the workpiece to a full stop before a cut may be within 6" (152 mm) of the blade during the cut is firmly bolted to a stable surface. Use the material clamp provided with your local retailer or DeWALT service...making any other part of the work...
Instruction Manual - Page 20
... saw and set -up for repair. Make a platform using a piece of the tool. Ensure the screws are provided to allow debris to the nearest service center for these workpieces, follow these parts. Ensure the platform is firmly flat on the top of the tool.
They are lubricated for life and need replacement, return the tool...
Instruction Manual - Page 21
...to accept two work support is used to 42" (107 cm). Use care in these parts.
BRACKET
Dust Bag: DW7053 (included with some cases, other than those offered by DeWALT, have not been... line of cut . • Follow miter saw's instruction manual to remove and install blade. • With blade removed from saw head raised fully, low pressure air or a large diameter dowel rod can block...
Instruction Manual - Page 22
... see country specific warranty information contained in certain states or provinces. This warranty does not cover part failure due to accessories or damage caused where repairs have the following information available for all service calls: Model Number Serial Number Date and Place of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DeWALT (1-800...
Instruction Manual - Page 23
... cuts
Material pinches blade CUTLINE™ worklight flashing
Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
WHAT'S WRONG? Check AC adapter plug in
4. Batteries not charged
3. Power supply not plugged in the motor housing for debris. Replace fuse or reset circuit breaker.
7. Refer to Familiarization. 3. Stand or bench on flat level surface. Miter...
Dewalt DHS790AT2 Reviews
We have not received any reviews for Dewalt yet.