Dewalt DCG440B Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DCG440B manuals!
Problems with Dewalt DCG440B?
Ask a Question
Free Dewalt DCG440B manuals!
Problems with Dewalt DCG440B?
Ask a Question
Popular Dewalt DCG440B Manual Pages
Instruction Manual - Page 6
... a key left attached to a rotating part of electric shock.
Cluttered or dark areas invite accidents. Do not use common sense when operating a power tool.
Never use the cord for outdoor use this power tool. Damaged or entangled cords increase the risk of injury, read the instruction manual. Protective equipment such as pipes, radiators...
Instruction Manual - Page 7
... situation. Read all safety warnings, instructions, illustrations and specifications provided with specifically designated battery packs. Use the correct... unpredictable behavior resulting in the instructions. Service of battery packs should only ...instructions and do not allow persons unfamiliar with the charger specified by a qualified repair person using only identical replacement parts...
Instruction Manual - Page 8
... operation. Vibration caused by the operating action of this manual is dropped, inspect for loose or cracked wires.
Damaged...) Use of control. Accessories with a new or replacement wheel, or a new or replacement wire brush installed, hold the tool in turn causes the uncontrolled power ... where the cutting accessory may make exposed metal parts of the rotating accessory and run out of ...
Instruction Manual - Page 9
... existing walls or other blind areas.
Avoid bouncing and snagging the accessory. Safety Warnings Specific for Grinding and
Abrasive Cutting‑Off Operations
a ) Use only wheel types that...of pinching. When the wheel, at the point of the disc or kickback.
7 e ) Support panels or any reason, switch off wheel or apply excessive pressure.
Larger sanding paper extending beyond ...
Instruction Manual - Page 10
...
read the safety instructions below and then ...parts.
CAUTION: When not in diameter due to ANSI S12.6 (S3.19) during ordinary operation. Failure to remove static and airborne dust could result.
WARNING: ALWAYS use face or dust mask if cutting operation is dusty. When ordering replacement.... English
Safety Warnings Specific for Wire
Brushing Operations... secure and support the workpiece...
Instruction Manual - Page 11
...label: USE: 120 Wh SHIPPING: 3 x 40 Wh
In this manual for compatibility of the charger. You may cause explosion.
•...product. In some areas, it for recycling. Failure to the service center for information on the battery pack. Shipping the DeWALT FLEXVOLT... them and cause a short circuit. Battery Pack Cleaning Instructions
Dirt and grease may be properly protected from short circuits...
Instruction Manual - Page 12
... to an authorized service center when service or repair is absolutely necessary...information and/or may cause them replaced immediately.
• Do not...or American Wire Gauge) for Cord Sets
Volts
Total Length of Cord in Feet... trademark of all safety warnings, instructions, and cautionary markings for blink patterns... chargers and battery packs are specifically designed to damage or stress....
Instruction Manual - Page 13
...and does not indicate a problem. Remove the four corner screws attaching the gear case to your local service center.
4. The tool ... Do not use water or
any adjustments or removing/ installing attachments or accessories. Wall Mounting
Some DeWALT chargers are ...become warm to sit upright on the wall.
Charger Cleaning Instructions
WARNING: Shock hazard. Dirt and grease may charge a...
Instruction Manual - Page 14
... used for any adjustments or removing/ installing attachments or accessories. The same guard...desired working position. torque.
Some DeWALT models are designed for surface grinding while ...away from your local dealer or authorized service center. Tighten screws to select the...(Fig. Refer to repair or replace the guard.
Mounting instructions for the manufacturer's label...
Instruction Manual - Page 15
... lock button 3 and use a damaged accessory. Follow the instructions given in the Accessories Chart.
• Make sure the ... normally break apart during this manual. An accidental start‑up . 2. To install the battery pack 11 into the...J) Hubbed wheels install directly on the spindle 4 by hand. K)
NOTE: For best results, make sure your local dealer or authorised service center. 1.
...
Instruction Manual - Page 16
...come to the tool, do not offer this manual. Operate the spindle lock only when the tool...mils thickness.
3. Lift the tool from rotating when installing or removing wheels.
A)
The spindle lock button 3...of dust generated.
2. Sanding should be replaced daily or whenever the wearer has difficulty... during use the correct guard per the instructions in this protection. Vacuum filter bags should...
Instruction Manual - Page 17
...to Tool Connect™ Chip Instruction Sheet for more information. Edge... making any adjustments or removing/ installing attachments or accessories. Use a...and dust out of this manual.
The capacity of all abrasive...surface grinding applications because these parts. Store in locating any...service center.
Accessory ratings must have not been tested with water and mild soap.
Instruction Manual - Page 18
...batteries).
Register Online
Thank you . no serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement, when applicable) should be performed by normal use identical replacement parts.
FREE WARNING LABEL REPLACEMENT: If your product will allow limitations...
Instruction Manual - Page 19
... intended for use the smallest proper guard possible that does not contact the accessory.
** NOTE: Available at extra cost from your local dealer or authorized service center. *** NOTE: These can be used with Type 1/41 cutting wheels and Type 27 wheels marked for cutting only. Grinding with wheels other than Type...
Dewalt DCG440B Reviews
We have not received any reviews for Dewalt yet.