Dewalt D28112 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt D28112 manuals!
Problems with Dewalt D28112?
Ask a Question
Free Dewalt D28112 manuals!
Problems with Dewalt D28112?
Ask a Question
Dewalt D28112 Videos
DeWalt D28112-AR Angle Grinder Maintenance. Soluciones Eléctricas Río Cuarto.
Duration: 3:43
Total Views: 130
Duration: 3:43
Total Views: 130
Popular Dewalt D28112 Manual Pages
Instruction Manual - Page 2
... all instructions listed below may...instructions. Cluttered benches
and dark areas invite accidents. • Do not operate power tools in explosive atmospheres, such
as pipes,
radiators, ranges and refrigerators. Replace damaged cords
immediately. When
using an extension cord, be plugged into an outlet properly
installed...parts...DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT...
Instruction Manual - Page 3
... injury.
• Dress properly. Air vents often cover moving parts. TOOL USE AND CARE
• Use clamps or other condition that may affect the tool's operation. Accessories that the grinding wheel backing flange has a yellow rubber ring (S) installed, see Figure 1.
Additional Specific Safety Instructions for one tool, may be used on another tool. A moment...
Instruction Manual - Page 4
... a new or replacement wheel, or a new or replacement wire brush installed, hold the tool...manual is a sudden reaction to a pinched, bound or misaligned wheel, wire brush...constitutes misuse.
• Do not use Type 11 (flaring cup) wheels on tool....
• Accessories must be above listed minimum wheel speed as follows:
V ... wire brush has loose wires, they will make exposed metal parts of power...
Instruction Manual - Page 5
...as the tool is restarted.
• Support large panels to minimize the risk of ... to a complete stop. Support must be placed under their own weight.
Slider Switch (D28110,
F. 4-1/2" Grinding Wheel
D28112)
G. English
• ...body. Investigate and take corrective actions to eliminate the cause of the grinder may be controlled by power sanding, sawing, grinding, drilling, and...
Instruction Manual - Page 6
... to use with grinder accessories. Accessories
It is tightened securely. Rotating the Gear Case
Turn off .
1.
NOTE: If the gear case and motor housing become separated by a DEWALT service center. Remove guard and flanges from motor
housing not more than 1/4", rotate the
gear case head to have the tool serviced may cause brush, motor and...
Instruction Manual - Page 7
...). The tool may burst and cause injury. Grinding and cutting with sanding flap discs (Type 27 and 29) and wire brushes. Mounting Guard
MOUNTING AND REMOVING GUARD (D28112, D28402, D28402N)
CAUTION: Turn off . Some DEWALT models are provided with a guard intended for these accessory guards are included in the accessory package.
6
Before reconnecting the tool...
Instruction Manual - Page 9
...guard.
5. Undetectable damage to repair or replace the guard.
CAUTION: If guard cannot be above listed minimum wheel speed as described above... the tool and guard to a service center to the guard or the ...performed with slots (O) on the
guard with Type 27 wheels designed and specified for a circular ...tool movement, do not use with the grinder accessories. Allow the tool to a complete...
Instruction Manual - Page 10
...power is retained to the grinder by pressing the rear part of the wheel.
4.
...D28112)
CAUTION: Before connecting the tool to a power supply, be sure
the switch is released. To stop . For continuous operation, slide the
switch toward the back of the switch
L
inward.
To lock the tool on and off and unplug the tool before making any
adjustments or removing or installing...
Instruction Manual - Page 11
...dealer or authorized service center.
1. Type 1 guards are installing is tightened, check the orientation of the backing flange.
3. Install the unthreaded ...manual for more than 1/2" in depth).
NOTE: If the wheel spins after the clamp nut is
more information. SURFACE GRINDING WITH GRINDING WHEELS
1. Allow the tool to reach full speed before touching the tool to 30˚ angle...
Instruction Manual - Page 13
... become sharp. Allow the tool to reach full speed before setting it down . Apply minimum pressure to the
work gloves when handling wire brushes
and wheels. Material removal rate is off . Maintain contact between the edge of grinder may result in use a wrench on the spindle by hand.
2. Continuously move the tool in...
Instruction Manual - Page 15
... the tool. CAUTION: Never use identical replacement parts. Apply minimum pressure to work surface, allowing tool to normal wear or tool abuse. Cutting rate is established in the workpiece, do not change the angle of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258) or visit our website...
Instruction Manual - Page 16
...questions asked. LATIN AMERICA: This warranty does not apply to the warranty, DEWALT tools are covered by our: 1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any reason, you are missing, ...full refund - English
In addition to products sold in Latin America, see country specific warranty information contained either in Latin America.
Instruction Manual - Page 52
... carga:
120 V AC/DC (
)
7 A
50/60 Hz
810 W
11 000/min
D28112 Tensión de alimentación: Consumo de corriente: Frecuencia de alimentación: Potencia nominal: Rotaci&#...DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (MAR06) Form No. 641881-00 D28110, D28112, D28402, D28402N Copyright © 2005, 2006 DEWALT
The following are trademarks for one or more DEWALT...
Parts Diagram - Page 2
... www.dewaltservicenet.com for D28112 Type 1
Description
Qty Required
623584-12S
ARMATURE ASSY.
1
623599-01
FIELD CASE
1
N012328SV
GEAR CASE ASSY
1
659967-00
GEAR
1
330065-31
SCREW
9
648743-00
ARM
2
623592-00
FELT SEAL
4
650916-01
BRUSH
2
623589-00
BRUSH SPRING
2
623591-00
CAP
2
593685-00
SCREW
2
625243-00SV
HANDLE SET
1
945614-00
SWITCH,ON...
Parts Diagram - Page 4
... www.dewaltservicenet.com for D28112 Type 1
Description
Qty Required
GREASE, 7LBS
1
GREASE,1 LB.
1
TORX DRIVER
1
SHIM
1
GUARD
1
4-1/2X1/4 METL
1
COPYRIGHT© 2005. Parts list, pricing, and availability subject to change.
Item Number
800 800 836 846 856 856
Part Number
429954-00 429954-01 233804-36 5140030-98 643772-00 DW4514
Parts List for current parts information. All...
Dewalt D28112 Reviews
We have not received any reviews for Dewalt yet.