EMC S3048-ON and S4048-ON Troubleshooting Guide March 2019
Page 16
...down arrow keys to the default ONIE settings. GNU GRUB version 2.02~beta2+e4a1fe391 | ONIE: Install OS | | *ONIE: Rescue | | ONIE: Uninstall OS | | ONIE: Update ONIE | | ONIE: Embed ONIE | | DELL EMC DIAG | | | | | | | | | | | 2 Press ENTER to activate the console. 3 You can also use the ... entry (*) executes automatically in the operating system. After ONIE Rescue completes, the system resets and boots to the ONIE console. 1 Restore the S4048-ON or S3048-ON factory defaults from Grub and select ONIE: Rescue. If it is highlighted. ONIE:/ # onie-...
...down arrow keys to the default ONIE settings. GNU GRUB version 2.02~beta2+e4a1fe391 | ONIE: Install OS | | *ONIE: Rescue | | ONIE: Uninstall OS | | ONIE: Update ONIE | | ONIE: Embed ONIE | | DELL EMC DIAG | | | | | | | | | | | 2 Press ENTER to activate the console. 3 You can also use the ... entry (*) executes automatically in the operating system. After ONIE Rescue completes, the system resets and boots to the ONIE console. 1 Restore the S4048-ON or S3048-ON factory defaults from Grub and select ONIE: Rescue. If it is highlighted. ONIE:/ # onie-...
OpenSwitch OPX Installation Guide with Enhancement Package Release 3.1.0
Page 6
...OPX using an industry-standard open network install environment (ONIE) software image with your switch or the platform-specific Installation Guide at www.dell.com/support. Installs a new ONIE version. • Embed ONIE - System setup Verify that results in an unsuccessful installation, perform ...system is an existing OS on the switch. required serial port settings are 115200, 8 data bits, and no parity. • Connect the Management port to access the ONIE boot menu. To locate the Console port and the Management port, see Manual installation). Deletes the contents...
...OPX using an industry-standard open network install environment (ONIE) software image with your switch or the platform-specific Installation Guide at www.dell.com/support. Installs a new ONIE version. • Embed ONIE - System setup Verify that results in an unsuccessful installation, perform ...system is an existing OS on the switch. required serial port settings are 115200, 8 data bits, and no parity. • Connect the Management port to access the ONIE boot menu. To locate the Console port and the Management port, see Manual installation). Deletes the contents...
EMC PowerSwitch Installation Guide March 2021
Page 32
... have a terminal emulation program already installed and running on the PSU-side of the S4048-ON chassis, as follows: ● 115200 baud rate-set the MicroUSB console port to -male adaptor. 1. If the cable is 6m. S4048-ON RS-232 console ports 1. Install the provided RJ-45 connector side of the provided copper cable into...
... have a terminal emulation program already installed and running on the PSU-side of the S4048-ON chassis, as follows: ● 115200 baud rate-set the MicroUSB console port to -male adaptor. 1. If the cable is 6m. S4048-ON RS-232 console ports 1. Install the provided RJ-45 connector side of the provided copper cable into...
EMC PowerSwitch Installation Guide March 2021
Page 33
Micro USB-B console port access The MicroUSB-B console port is on the I/O side of 2048 * 512 = 1048576 bytes Device Boot Start End Blocks Id System 3. Install the necessary USB device drivers. 6. View the fixed disks using fdisk. Confirm that the terminal settings on the PC. 2. ONIE:/mnt # fdisk -l For internal ... switch uses the Silicon Labs CP2109 USB-B chip. Connect the MicroUSB-B end of cable into the MicroUSB-B console port on the S4048-ON. 5. NOTE: The following message displays if the /mnt/usb directory is not seen: mount: mounting /dev/sdb on /mnt/usb ...
Micro USB-B console port access The MicroUSB-B console port is on the I/O side of 2048 * 512 = 1048576 bytes Device Boot Start End Blocks Id System 3. Install the necessary USB device drivers. 6. View the fixed disks using fdisk. Confirm that the terminal settings on the PC. 2. ONIE:/mnt # fdisk -l For internal ... switch uses the Silicon Labs CP2109 USB-B chip. Connect the MicroUSB-B end of cable into the MicroUSB-B console port on the S4048-ON. 5. NOTE: The following message displays if the /mnt/usb directory is not seen: mount: mounting /dev/sdb on /mnt/usb ...