Cub Cadet 3X 34 inch MAX H INTELLIPOWER EFI Support and Manuals
Get Help and Manuals for this Cub Cadet item
View All Support Options Below
Free Cub Cadet 3X 34 inch MAX H INTELLIPOWER EFI manuals!
Problems with Cub Cadet 3X 34 inch MAX H INTELLIPOWER EFI?
Ask a Question
Free Cub Cadet 3X 34 inch MAX H INTELLIPOWER EFI manuals!
Problems with Cub Cadet 3X 34 inch MAX H INTELLIPOWER EFI?
Ask a Question
Popular Cub Cadet 3X 34 inch MAX H INTELLIPOWER EFI Manual Pages
Operation Manual - Page 1
... California to comply with a local authorized service dealer.
Form No. 769-26795 (April 20, 2023) SAVE THESE INSTRUCTIONS. This information will be necessary, should you seek technical support via our web site, Customer Support Department, or with these instructions may result in this machine. NOTE: This Operator's Manual covers several models. Failure to cause cancer and birth...
Operation Manual - Page 4
... -season storage.
12. Wait until all components and replace with factory setting of your hand in any damage.
4. Snow blower shave plates and skid shoes are not covered in accidents, injuries or death. For your hands. Environmental Protection Agency (EPA), this operator's manual for proper instructions on regular unleaded gasoline, and may lead to...
Operation Manual - Page 6
...models with side supports. b
b
a
a
b
Figure 2
IMPORTANT: Place shift lever in Forward-6 position or fastest forward speed (if equipped).
3.
NOTE: On select models, chute-pitch control cables will not use roller guides. They are aligned and seated properly in roller guides... handle and set aside as shown in Figure 1 or Figure 2 for packaging purposes only. Refer to Set-up.
&#...
Operation Manual - Page 7
...Control
*NOTE: This model may
be equipped with
b
side supports. See Figure 5 or Figure 6 for
your "Chute Control
Style" and continue to the "Assembly" instructions for models with a
metal chute assembly. SET-UP
5. c b
c
c a
a b
a a
Figure 5
CHUTE CONTROL STYLES
Chute Assembly Chute Control
Rod
c
Figure 6
STOP
b
Refer to Figure 7 below to identify your specific style on pages13...
Operation Manual - Page 12
...Set-Up (page 14). SET-UP
6.
Perform one of its rotation see Figure 33, Detail "A" for models without hydro transmission or Detail "B" for models with a metal chute assembly -
Tighten jam nut. 5. Figure 30
• Models...need to the chute control rod coupling: • Models with Electric Chute Control - e
c
a
Chute Control Rod
or
Manual Chute Control Rod
f
b d
Figure 32
3....
Operation Manual - Page 13
...Manual Chute Rotation Control & Electric Chute Control on page 16. Insert other end of chute control rod into chute control head as far into chute control head. Finish securing chute control head by installing...39 inset).
SET-UP
1....support bracket with middle hole in chute control coupler and insert cotter pin (a) removed in Step 1 (Figure 37). NOTE: For models equipped with manual...
Operation Manual - Page 16
... which secure the bracket and reposition
it slightly (Figure 50). 2.
a
Figure 49 2. On models with manual chute pitch, the distance snow is thrown can be adjusted by changing angle of chute assembly....auger housing (Figure 53). Pivot chute upward or downward before re-tightening wing
nut. SET-UP
Adjustable Drift Cutters (If Equipped) The drift cutters are mounted inverted at bottom...
Operation Manual - Page 17
SET-UP
a
a
b
b
b
b
b a
d
c
c
c
c
Figure 53
NOTE: 3-Stage model... shift cable to verify your Engine Operator's Manual.
3. See Skid Shoes on auger control ...in cable or downward to remain engaged for ALL moving parts to provide more
slack in -lbs (11.3-13 Nm... speed position. 2. Reinstall and securely tighten all instructions below. When auger control lever is operating safely ...
Operation Manual - Page 18
... and in the shift lever (Figure 56). Refer to the Engine Operator's Manual. Loosen upper hex screw (a) on drive cable bracket (b) (Figure 58). Check for models with the washer and cotter pin. A
B
NON-HYDRO MODELS
HYDRO MODELS
Figure 57
4. Drive Control (NON-Hydro Models) (If Equipped)
When drive control lever is released and in drive...
Operation Manual - Page 19
... the battery pack from the battery box. (c) c. IMPORTANT: Refer to instructional manual supplied with care and keep away from sources of your nearest servicing dealer. NOTE: Do not use . Failure to the Engine Operator's Manual for charging, maintenance and battery disposal instructions. INSTALLING/REMOVING THE BATTERY PACK 1. b. b a
g d
c f
e
Figure 61
Figure 60
ADDING FUEL...
Operation Manual - Page 21
...located on the front of travel. Read and follow all instructions carefully and perform all adjustments to the reverse direction will be... references to operating your machine's drive system.
*On select models, the drive control lever also locks the auger control lever... the Assembly & Set-Up section prior to the left handle) and the augers will result in this manual are applicable to Skid...
Operation Manual - Page 27
...damaged parts.
&#...servicing, repairing or inspecting the snow blower, disengage the auger control lever. Drive control cable in need of adjustment. See Installing/Removing The Battery Pack on select models) have two wear edges. Refer to Clearing a Clogged Chute Assembly on page 30.
TROUBLESHOOTING
Chute fails to Replacing Shear Pins on page 26. Refer to the Engine Operator's Manual...
Operation Manual - Page 28
...retailer.
*NOTE: TruFuel® highly recommended. Non-Hydro Models (If Equipped)
a b
Figure 81
The friction wheel... until fuel tank is empty and it is not being serviced, it stops due to coat the snow blower.
7.
...Installing/Removing The Battery Pack on page 28.
5. Lubricate machine as instructed on page 19.
4. IMPORTANT: When storing or when it is to Engine Operator's Manual...
Operation Manual - Page 30
...control cable adjustment fails to correct problem, the friction wheel may need to have friction wheel rubber replaced or contact Customer Support. Carefully pivot snow blower up ... spring to dislodge ball bearing from underside by following instructions in first Forward (F1) position. 3. Refer to axle. Follow the instructions below. Place shift lever in reverse order. Remove ...
Operation Manual - Page 31
...
Figure 93 10. Apply a light coating of your authorized service dealer to hex shaft.
13. After replacing friction wheel, perform Drive Control test shown on page 18. Hydro Transmission (If Equipped) NOTE: See your nearest servicing dealer. Carefully position hex shaft downward and to instructional manual supplied with equal force (between the plates. 11. BATTERY...
Cub Cadet 3X 34 inch MAX H INTELLIPOWER EFI Reviews
We have not received any reviews for Cub Cadet yet.