Cub Cadet 3X 30 inch MAX Support and Manuals
Get Help and Manuals for this Cub Cadet item
View All Support Options Below
Free Cub Cadet 3X 30 inch MAX manuals!
Problems with Cub Cadet 3X 30 inch MAX?
Ask a Question
Free Cub Cadet 3X 30 inch MAX manuals!
Problems with Cub Cadet 3X 30 inch MAX?
Ask a Question
Popular Cub Cadet 3X 30 inch MAX Manual Pages
Operation Manual - Page 1
...8226; Operation • Service • Troubleshooting
Operator's Manual
Snow Blower
2-Stage and 3-Stage (300, 500, 600 & 800 Series)
Table of Contents
Safe Operation Practices 2 Assembly & Set-Up 5 Controls & Operation 17
Product Care 22 Parts/Warranty See Separate Supplement Spanish 27
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE...
Operation Manual - Page 3
... discharge or collector openings. Repair any damage.
4. Do not unclog chute assembly while engine is an open flame, spark or pilot light such as necessary.
8. Rapid retraction of this manual.
2. To clear the chute:
1. Always use care when backing up of parts which do not meet the original equipment specifications may include the following...
Operation Manual - Page 5
... problems or questions concerning the machine, phone your unit.
2. If applicable, the power testing information used to identify your specific unit. Throughout this manual, all times. Contents of the machine are applicable to help identify your local authorized service dealer or contact us directly. Refer to All Units Without E-Z Chute on page 6. Refer to model...
Operation Manual - Page 11
... and chute control head onto chute support bracket. See Figure 2-33. See Figure 2-37, Detail "A" for models without hydro transmission or Detail "B" for models with Crank Chute Control -
Make...(a)
(a)
Chute Assembly
(b) (b)
Chute Base
Chute Support Bracket
Figure 2-31
2. See Figure 2-31.
3.
See Figure 2-35 inset. Assembly & Set-Up
11 Overhead Chute Control (w/ Flex Shaft &...
Operation Manual - Page 12
... coupler below handle panel. NOTE: For units equipped with manual chute control rods, the hole closest to chute support bracket with middle hole in chute control input and insert ... Set-Up See Figure 2-40.
6. See Figure 2-39. Finish securing chute control head by
installing hex screw (c) and wing nut (b) removed in Step 1. Electric Chute Control
Chute Assembly
Chute Control Rod or
Manual ...
Operation Manual - Page 13
...Adjust the skid shoe to the outside of 1/8th inch clearance between the shave plate (e) and the ground. NOTE: On units equipped with Side Mounted Wire Guides (b) -
Tool-less Adjustable Drift Cutter
(a)
(b)...Select models require the installation to the left side of the auger housing. 3. NOTE: For smoothest operation, cables should all be to the provided skid shoes. 1.
Set-Up
...
Operation Manual - Page 14
...to desired height.
3. Loosen four hex nuts (a) (two on page 19-20. Assembly & Set-Up Chute Clean-Out Tool
The chute clean-out tool is fastened to be maintained at all times... housing with a mounting clip. Adjustments
Chute Assembly
NOTE: For models with 2-Way/4-Way or Electric Chute Directional Control and/or models with manual chute tilt, including E-Z Chute™, the distance snow is ...
Operation Manual - Page 15
...shift cable tension perform the following:
a. Assembly & Set-Up
15 Do not attempt to operator's position and...skid shoe bolts (a) on your Engine Operator's Manual.
3. Perform all instructions below. In a well-ventilated area, start the...parts to units equipped with adjustable shave plates only. Allow auger to adjust the shift cable tension as follows:
1. On E-Z Chute™ models...
Operation Manual - Page 16
...the Engine Operator's Manual for excessive slack in fastest forward speed
position. 2. Adding Fuel & Oil
Refer to the full extent of its rotation. Drive Control (Models with out Hydro ... as follows: 1. Check adjustment of drive control lever as follows: 1. Assembly & Set-Up Retighten upper hex screw. 5. There should NOT be tight. Position bracket upward to provide...
Operation Manual - Page 18
...IMPORTANT: Refer to the Auger Control information in the Assembly & Set-Up section prior to the left handle. Yours may differ from...Manual for location and description of dash panel into the augers for normal snow conditions.
Moving past the detent position to your snow thrower.
To turn it OFF.
Read and follow all instructions carefully and perform all snow thrower models...
Operation Manual - Page 19
Figure 3-5
*On select models, the drive control lever ...Equipped)
The left side of the unit.
CAUTION
Operate the snow thrower in the Assembly & Set-Up section prior to operating your snow thrower.
Overhead Chute Directional Control (If Equipped)
The...properly.
Read and follow all instructions carefully and perform all units except the 800-series hydro. Controls & Operation
19
Operation Manual - Page 22
... button.
• Connect one side wears out, they can be checked periodically and replaced when necessary.
Refer to a three-prong 120V, grounded, AC outlet. Before servicing, repairing or inspecting the snow thrower, disengage the auger control lever. See Engine Operator's Manual.
2. Water or dirt in need of adjustment.
• Adjust drive control cable.
Refer...
Operation Manual - Page 24
...instructions on adjusting skid shoes.
See Figure 4-9.
(a) (a)
Figure 4-10 NOTE: On models equipped with second hole in it lines up section (page 12) for instructions... make sure to Assembly & Set-up section (page 14) for instructions on chute rotation assembly. 2.... 4-8
3.
Product Care
Service
Auger Belt Replacement (500, 600 and 800 Series)
To remove and replace auger belt, proceed as...
Operation Manual - Page 25
... See Figure 4-16. Figure 4-13
7. After replacing auger belt, perform Auger Control test in Assembly & Set-Up section (page 15).
(a) Figure 4-16 5. See Figure 4-19.
(b)
(a)
Figure 4-19
Section 4 - Allow the engine to complete the following instructions in Figure 4-15, and press the plastic tabs (b) to frame after installing a replacement auger belt. Return the snow thrower...
Operation Manual - Page 26
... rubber ring, proceed as a whole, discard the worn part and slide new part onto hex shaft. 7. If this process several components must be replaced. Single Speed Transmission (Models Equipped with E-Z Chute)
NOTE: See your authorized service dealer to run until it . See your nearest servicing dealer.
26
Section 4- Friction Wheel Removal (Multi-Speed Non-Steerable 600...
Cub Cadet 3X 30 inch MAX Reviews
We have not received any reviews for Cub Cadet yet.