Operating Instructions
Page 1
... the list. 2. When ordering repair par_, always give the folbwing information: I. Always mention the Model Number when communicating with us regarding youe saw , at the back, near the bottom of the b_. The model number which is I13.2240i ROEBUCK OPERATING INSTRUCTIONS AND LIST C n 8-1 h Tilting Arbor Number 113.2240 | The above Modal Number will be order_ through a Sears retail or mar order store. The part number...
... the list. 2. When ordering repair par_, always give the folbwing information: I. Always mention the Model Number when communicating with us regarding youe saw , at the back, near the bottom of the b_. The model number which is I13.2240i ROEBUCK OPERATING INSTRUCTIONS AND LIST C n 8-1 h Tilting Arbor Number 113.2240 | The above Modal Number will be order_ through a Sears retail or mar order store. The part number...
Operating Instructions
Page 2
... _e desired adjustment has been obtained. 3, Mount the Guard Assembly "X" on the rack. ter Made damp washers may be changed_ if n_essary, by tightening the two square head set screws (part S-207, Fig. No_ 3). through all obstructions saw is necessar B loosen the screws (part: S-860, Fig. Remove two screws (part So1241_ Fig. If any part of the Rip Fence Rip Fence and the top of Iine with a 3450 r.p,m., alternating.current motor of the...
... _e desired adjustment has been obtained. 3, Mount the Guard Assembly "X" on the rack. ter Made damp washers may be changed_ if n_essary, by tightening the two square head set screws (part S-207, Fig. No_ 3). through all obstructions saw is necessar B loosen the screws (part: S-860, Fig. Remove two screws (part So1241_ Fig. If any part of the Rip Fence Rip Fence and the top of Iine with a 3450 r.p,m., alternating.current motor of the...
Operating Instructions
Page 3
... the loads normally encountered. This adjustment will not give sadsfacto_ ormance_ saw blade sho_x_d be made by use when it may be cut measured. Tilt Hand Wheel "C'_ on the left of the: clamp rod at the exact angle required_ 3. Elevation Hand Wheel "A', on the Depth Dial "B'. Non 3) and readjusting the hex nut (part S-108, Fig. Keeping the saw _ble and rip fence clean and tap#hi the rip fence lightly* to...
... the loads normally encountered. This adjustment will not give sadsfacto_ ormance_ saw blade sho_x_d be made by use when it may be cut measured. Tilt Hand Wheel "C'_ on the left of the: clamp rod at the exact angle required_ 3. Elevation Hand Wheel "A', on the Depth Dial "B'. Non 3) and readjusting the hex nut (part S-108, Fig. Keeping the saw _ble and rip fence clean and tap#hi the rip fence lightly* to...
Operating Instructions
Page 4
... o_r %top Rust" when not in use a special Dado Insert (Cat. If _ dude cut is neces_ry for the cutters in the Rip Fence and Mitre Gage. To prevent the saw arbor nut firmly. No. 3) and saw with a cloth before using. All other unpainted and unplated parts and s_rfaces. Place one outside dude blade, Replace _e loose collar and tighten the saw table from the ruble entirely _c provide...
... o_r %top Rust" when not in use a special Dado Insert (Cat. If _ dude cut is neces_ry for the cutters in the Rip Fence and Mitre Gage. To prevent the saw arbor nut firmly. No. 3) and saw with a cloth before using. All other unpainted and unplated parts and s_rfaces. Place one outside dude blade, Replace _e loose collar and tighten the saw table from the ruble entirely _c provide...
Operating Instructions
Page 5
... Rod Clam_ .... Ag_5". Sp_ir_g Cli# ASSEMBLY Washer -- In severa_ itas_a_ceg par_ number2 and p_iees a_e listed for these pa_ts. GUARD ASSENtBLY Slflit_e¢ Plvo_ Pin 8" Saw P_t --- berg of the COMPLETE ASSEMBLiES_ howevee, do not appea_ on the fallowing pages u_der part humbess mast he ¢ ...... PART MITRE GAGE _it_'e r}age ASSY. g _/4"1 Wir_ Nut 10-24 Motet Molo_ Mete€...
... Rod Clam_ .... Ag_5". Sp_ir_g Cli# ASSEMBLY Washer -- In severa_ itas_a_ceg par_ number2 and p_iees a_e listed for these pa_ts. GUARD ASSENtBLY Slflit_e¢ Plvo_ Pin 8" Saw P_t --- berg of the COMPLETE ASSEMBLiES_ howevee, do not appea_ on the fallowing pages u_der part humbess mast he ¢ ...... PART MITRE GAGE _it_'e r}age ASSY. g _/4"1 Wir_ Nut 10-24 Motet Molo_ Mete€...
Operating Instructions
Page 6
... Prepaid Price NAME OF PART E_¢h_ 3_I6 x I /2 Fil. _d. Saw Base Assemble ......... SCREW ASSEMBL_ Screw ........... . . Sheet Metal N_rew _0 Prepnid Par_ No. Hd. S 108 S*ItO S-il2 Sd42 S-170 S.205 S .207 S.219 S_275 S,297 S-310 Sdl2 NAME OF PART Prcl_a_d P_i¢¢ Ezch 10--_2 x 1/8 Hex Nu_ ...... C_ Screw I0 5 16_I8x1 Fil+ Hd. Arbor Wrench ............ I0 10_2 g I Hex. See...
... Prepaid Price NAME OF PART E_¢h_ 3_I6 x I /2 Fil. _d. Saw Base Assemble ......... SCREW ASSEMBL_ Screw ........... . . Sheet Metal N_rew _0 Prepnid Par_ No. Hd. S 108 S*ItO S-il2 Sd42 S-170 S.205 S .207 S.219 S_275 S,297 S-310 Sdl2 NAME OF PART Prcl_a_d P_i¢¢ Ezch 10--_2 x 1/8 Hex Nu_ ...... C_ Screw I0 5 16_I8x1 Fil+ Hd. Arbor Wrench ............ I0 10_2 g I Hex. See...