Craftsman 21217 - 12 in. Miter Saw Support and Manuals
Get Help and Manuals for this Craftsman item
View All Support Options Below
Free Craftsman 21217 manuals!
Problems with Craftsman 21217?
Ask a Question
Free Craftsman 21217 manuals!
Problems with Craftsman 21217?
Ask a Question
Popular Craftsman 21217 Manual Pages
Operation Manual - Page 1
... this Miter Saw, read this manual and follow all its Safety Rules and Operating Instructions
Customer Help Line For Techr|ical Support
1-800-843-1682
• Safety Instructions • Installation • Operation • Maintenance • Parts List
Sears Parts &
Repair Center 1-800-488=1222
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit our Craftsman website: www.sears.com...
Operation Manual - Page 2
...
Warranty Product Specifications Power Tool Safety Compound Miter Saw Safety Electrical Requirements and Safety Accessories and Attachments
Tools Needed for Assembly Carton Contents
PAGE
2 2 4 5 5 7
7 8
SECTION
Know Your Compound Miter Saw Glossary of Terms Assembly and Adjustments Operation Maintenance Troubleshooting Guide Parts List
PAGE
9 10 11 17 23 24 25
CRAFTSMAN ONE...
Operation Manual - Page 5
... resuming operation. This miter saw blade, the workpiece should be clamped in any part of the saw blade.
17. PROVIDE adequate support to full speed before removing or securing the workpiece, changing the workpiece angle or changing the angle of the saw is turned ON.
18. DISCONNECT the saw .
11. POWER SUPPLY AND MOTOR SPECIFICATIONS The AC motor...
Operation Manual - Page 6
... 10% above or
below shows the correct size to start , release the trigger switch
immediately. To avoid electrocution: 1. ELECTRICARLEQUIREMENT- When servicing, use depending on the nameplate. Polarized plugs - IMPROPER or dull saw has a plug that looks like the one blade is free, try to use only identical replacement parts. Do not change the plug in...
Operation Manual - Page 8
... built-in the power cord until the missing or damaged part is correctly replaced. iMPORTANT: Do not lift miter saw .
. Lift machine by the trigger switch handle. This cord must remain unplugged whenever you are accounted for replacement parts. To avoid electric shock, use only identical replacement parts when servicing double insulated tools. It may cause misalignment.
UNPACKING YOUR...
Operation Manual - Page 10
... without using a fence (guide), hold down on the handle.
FREEHAND - Performing a cut made across the width of the blade.
A sticky sap from twisting during blade replacement or removal. Misalignment of the workpiece.
KERF -
MITER CUT - An angle cut .
RESIN - REVOLUTIONS PER MINUTE (RPM) - The number of the workpiece.
SAW BLADE PATH - SET - The distance between...
Operation Manual - Page 13
...blade collar must be placed against the fence (2) as saw . Thread the arbor bolt (4) onto the arbor (9) in setting the desired miter angles from an accidental start, make sure the switch... miter table by tightening the miter handle. 4. Position the miter table at the desired angle quickly and accurately. arbor with a 5/8 in the clockwise direction. While holding it in . Install...
Operation Manual - Page 15
.... O
10 12
Mounting instructions (if stand is not used for holding the saw , disconnect the power cord
from flying debris, do not allow visitors to stand behind the saw to a stable work bench or recommended leg set. Securethelockingnut(11)intopositionafter alignmenist achieved.
It is for handling and proper support of the saw in the lower position...
Operation Manual - Page 16
... on /off switch must be turned on for the laser line to show.
,_ WARNING i o AVOID DIRECT EYE CONTACT
Laser radiated when laser guide is turned on the stock to be cut before starting the miter saw must be connected to the power source and the laser on/off rocker switch (1) to preview the...
Operation Manual - Page 17
...lower guard:
Push the cutting arm all safety instructions and operating procedures in this miter saw is no excessive play in any electrical parts don't work on . If any part of this Operator's Manual. (SAFETY & OPERATIONS)
o Review the MAINTENANCE and TROUBLESHOOTING GUIDE for :
o Alignment of moving parts o Damaged electric cords o Binding of moving parts o Mounting holes o Function of the...
Operation Manual - Page 18
... help feed, support, or pull the workpiece.
Remove all applicable safety instructions, when cutting non=ferrous metals: o Use only saw .
INSPECT YOUR WORKPIECE
Make sure there are too small to help hold the
work to avoid small pieces that may bind, or that is longer or wider than the basic miter saw blade the workpiece...
Operation Manual - Page 21
... of the bevel cut. The auxiliary wood fence must let the workpiece lay flat on a flat surface, the miter saw blade to catch the cut -off piece and throw it toward the saw . Z
WORKPIECE SUPPORT (FIG. The support must be removed when bevel cutting.
SLiDiNGFENCE(FIG.Z)
1,_ WARNING j The sliding fence must be extended when making...
Operation Manual - Page 24
... limit switch. 2. See MAINTENANCE section, 3. Replace Brushes. TROUBLESHOOTING GUIDE = SAW OPERATION
PROBLEM
PROBLEM CAUSE
SUGGESTED CORRECTIVE ACTION
Blade hits table. Angle of
defective or wrong size blade or rapid ON/OFF cycling. 3. See ADJUSTMENT - Miter Angle Adjustment section. Loose pivot points.
1.
Pivot bolt too tight.
1.
Blade binds, jams, burns wood.
1. Improper...
Operation Manual - Page 25
... MITER SAW
MODEL NO. 137.212170
[_ WARNING]
When servicing use only CRAFTSMAN replacement parts, Use of any other parts many create a HAZARD or cause product damage, Any attempt to repair or replace electrical parts on this Miter Saw may create a HAZARD unless repair is done by a qualified service technician, Repair service is available at your nearest Sears Service Center,
PARTS LiST FOR SAW...
Operation Manual - Page 27
RE. SCREW & WASHER FIELD ASS'Y BALL BEARING BALL BEARING
Size (p4-30 M5"0.8-6 M5"0.8-12 M5* 12-60 M5"0.8-6
#AW
M5"0.8-35 6200ZZ 6201ZLU
MODEL NO. 137.212170
QTY 1 2 3 2 2 1 1 1 1 2 2 2 1 1 1 1 1 1 1 4 1 1 1
Y3ZY
OQ9K OQR2
21AX
/ COMPOUND MITER SAW PARTS LiST AND SCHEMATIC FOR MOTOR
I.D. 0JCF 0JX2 0K44 0KCP 0KLA 0Q9K 0QGR 0QMK 0QMY 0QQS 0QQT 0QR0 0QR2 144L...
Craftsman 21217 Reviews
We have not received any reviews for Craftsman yet.