Cisco WS-X4448-GB-RJ45 - Line Card Switch Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-X4448-GB-RJ45 manuals!
Problems with Cisco WS-X4448-GB-RJ45?
Ask a Question
Free Cisco WS-X4448-GB-RJ45 manuals!
Problems with Cisco WS-X4448-GB-RJ45?
Ask a Question
Cisco WS-X4448-GB-RJ45 Videos
Cisco WS-X4448-GB-RJ45 $275 Price Reduction
Duration: :34
Total Views: 5
Duration: :34
Total Views: 5
Popular Cisco WS-X4448-GB-RJ45 Manual Pages
Hardware Maintenance Manual - Page 3
... to nonconforming Software upon contact will be eligible for any installation, handling, maintenance, or operating instructions supplied by Cisco, (2) has not been installed, operated, repaired, or maintained in this manual is subject to restrictions as authorized by Cisco, (3) has been subjected to the Cisco Service Partner if the Software was exported under the multinational uplift...
Hardware Maintenance Manual - Page 4
..., or (iii) refund the price paid for shipment of advance replacements to the multinational uplift program as soon as set forth in Cisco's recommended spares list. Customer will be able to be eligible for the products listed in subparagraph (c) of an uplift.
Restricted Rights clause at Cisco's option and through a Sales or Service Partner if necessary, to Customer...
Hardware Maintenance Manual - Page 5
TABLE OF CONTENTS
About This Manual xv Document Objectives xv Audience xv Document Organization xv Document Conventions xvi
Chapter 1 Cisco 4000 Series Overview 1-1 External Differences in Models of the Cisco 4000 Series 1-1 Series Specifications 1-2 Memory Systems 1-4
Chapter 2 Preparing for Installation 2-1 Safety Recommendations 2-2 Safety with Electricity 2-2 Preventing Electrostatic Discharge...
Hardware Maintenance Manual - Page 15
...'s online library of the Cisco 4000 Series Hardware Installation and Maintenance publication. Audience
This publication is updated and shipped monthly, so it may be familiar with a DC-input power supply. About This Manual xv
Document Objectives
This publication contains the initial site preparation, installation, troubleshooting, and selected upgrade and maintenance procedures.
For...
Hardware Maintenance Manual - Page 16
... Initial Hardware Configuration," includes a troubleshooting
overview, problem-solving instructions, environmental reporting features, and understanding front-panel and network-processor module LED indicators.
• Chapter 5, "Maintaining and Upgrading the Router," includes instructions for opening the
chassis, replacing or adding network processor modules, and replacing single in-line memory...
Hardware Maintenance Manual - Page 37
...Installation 2-15 however, you can get good results with rates and distances greater than those shown in Table 2-4 are subject to 64 Kbps.
Typically, EIA/TIA-449 and EIA-530 support 2-Mbps rates, and V.35 can travel greater distances than those listed...
1025
312
513
156
256
78
102
31
50
15
Balanced drivers allow EIA/TIA-449 signals to travel a limited distance at ...
Hardware Maintenance Manual - Page 43
...manually changed. Figure 2-22 Dual Serial Network Processor Module Jumpers, J4 and J5-NRZI Setting...service representative, is normally ordered with the clockrate command. and EIA-530 DTE. An error message will be configured with the system. Nine different serial cables are not interchangeable.
See the appendix "Cabling Specifications." To set... for Installation 2-21 For more information...
Hardware Maintenance Manual - Page 45
...instructions... Serial Module All Cisco 4000 series router serial interfaces support CRC-CCITT, a...include interface, the type of interface (for Installation 2-23
When the serial port is a ...support both nonreturn to zero (NRZ) and nonreturn to zero inverted (NRZI) formats. Both formats use the same setting...a calculated numeric value to detect errors in IBM environments.
NRZ signals ...
Hardware Maintenance Manual - Page 54
... 6.3 (CCITT specification) • Input port specifications: see Figure 2-35) controls this function. On the CE1, the controller provides up to a channel service unit (CSU). The CE1, shown in Figure 2-34, provides a controller for a remote site. The figure shows the cable impedance set the cable impedance to 120-ohm.
2-32 Cisco 4000 Series Hardware Installation and Maintenance...
Hardware Maintenance Manual - Page 55
... reduce the potential for Installation 2-33
All of these jumpers must be configured by trained service personnel only. Warning To prevent problems with no ground. Figure...setting that could pose a risk of severe injury.
For the CE1 module, four serial cables are available from Cisco Systems. All three have DB-15 connectors on the CE1end and either impedance option, a jumper installed...
Hardware Maintenance Manual - Page 59
...instructions for initial startup and configuration, you must connect an EIA/TIA-232 cable between the chassis and the supporting surface for the different mounting options involve removing the front panel and component tray from the chassis shell and then installing.... The optional rack-mount/wall-mount kit ships with its own set of this chapter follow:
• Rack-Mount and Wall-Mount ...
Hardware Maintenance Manual - Page 64
...each direction at OSI Layer 1. BRI Cable Specifications The specifications for the BRI cable are accessible in this...supports eight BRI ports. The BRI module does not support a point-to the Integrated Services Digital Network (ISDN) through an ISDN channel service unit/digital service unit (CSU/DSU) called the NT1. Each BRI port is customer owned.
3-6 Cisco 4000 Series Hardware Installation...
Hardware Maintenance Manual - Page 123
...monitor prompt.
If you can reset the configuration register to 0x0, you must manually boot the system each time you set the software configuration register (bits 3, 2, 1, and 0) to booting in...During the 60-second window, you isolate or rule out hardware problems encountered when installing your router. Entering the Cisco 4000-M ROM Monitor Program
The ROM monitor diagnostics help you can...
Hardware Maintenance Manual - Page 127
..., you will have to manually boot the system from the console each time you isolate or rule out hardware problems encountered when installing your router. During the 60-second window, you can break to zero, you set the software configuration register (bits 3, 2, 1, and 0) to the ROM monitor prompt.
Cisco 4500-M and Cisco 4700 ROM Monitor D-1
The...
Hardware Maintenance Manual - Page 141
...publications xv overview, series 1-1
P
packing list 2-36 pinouts
auxiliary port A-2 BRI ...specifications 1-3 supply features 2-4 system, troubleshooting 4-2 preparing for installation 2-1 to make connections 2-7 preventing ESD damage 2-3 preventive site configuration 2-4 printing summary of ROM monitor commands problem indications 4-3 temperature 4-3 problem solving 4-1 processor specifications...
Cisco WS-X4448-GB-RJ45 Reviews
We have not received any reviews for Cisco yet.