Cisco CISCO7204VXR-CH - 7204VXR 4SLOT CHASSIS 1 Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco CISCO7204VXR-CH manuals!
Problems with Cisco CISCO7204VXR-CH?
Ask a Question
Free Cisco CISCO7204VXR-CH manuals!
Problems with Cisco CISCO7204VXR-CH?
Ask a Question
Popular Cisco CISCO7204VXR-CH Manual Pages
Configuration Guide - Page 33
... from being performed during an in-service software upgrade (ISSU) and some of the ports on the local port. You can configure UDLD aggressive mode only on the local device into error disabled state. Tip When a line card upgrade is shutdown, UDLD puts the corresponding port on point-to nexus7k-docfeedback@cisco.com
Default UDLD Configuration
Table 2-4 shows...
Configuration Guide - Page 52
...-config
2-28
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03
or 100-Mb/s speed, the port is automatically configured to be autonegotiated. If you set the speed for...want to set the local port to use a specific speed, you must set the remote port for the same speed or set to use half-duplex mode, but you should set the speed before setting the ...
Configuration Guide - Page 63
... on Different Interfaces
Description Default setting Enable UDLD command Disable UDLD command
Fiber port Enabled no udld disable udld disable
Copper or Non-fiber port Disabled udld enable no feature ...slot/port 6. configure terminal 2. copy running-config startup-config
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
2-39 show udld [ethernet slot/port |...
Configuration Guide - Page 64
... this command in interface command model. (Optional) Specifies an interface to configure for the device. Disables UDLD for more details. (Optional) Displays the UDLD status.
2-40
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
OL-23435-03 To enable UDLD on copper ports. To enable UDLD on fiber ports, the command is udld enable...
Configuration Guide - Page 109
...Cisco NX-OS FCoE Configuration Guide for Cisco Nexus 7000 and Cisco MDS 9500 for routing. This section includes the following sections: • Information About Layer 3 Interfaces, page 4-1 • Licensing Requirements for Layer 3 Interfaces, page 4-5 • Guidelines and Limitations, page 4-5 • Default Settings...FEX) port as a Layer 3 interface. See the Configuring the Cisco Nexus ...
Configuration Guide - Page 132
... at no license.
Any feature not included in a license package is bundled with the configuration tasks. Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
5-4
OL-23435-03 By default, Cisco DC-OS places you in -service software upgrades (ISSUs). Licensing Requirements for BFD
Chapter 5 Configuring Bidirectional Forwarding Detection
Send document comments to nexus7k...
Configuration Guide - Page 158
... topics: • Port Channels, page 6-3 • Port-Channel Interfaces, page 6-3 • Basic Settings, page 6-4 • Compatibility Requirements, page 6-5 • Load Balancing Using Port Channels, page 6-6 • LACP, page 6-8 • Virtualization Support, page 6-13 • High Availability, page 6-13
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
6-2
OL...
Configuration Guide - Page 166
... remote system, or partner, supports LACP. LACP ID Parameters
This section describes the LACP parameters in active mode can configure a value between ports to active or passive before enabling LACP, the device displays an error message. If you can form a port channel with another port that is in active mode.
• A port in the following examples...
Configuration Guide - Page 176
...). show interface type slot/port 6.
The Cisco DC-OS software creates the port channel associated with some incompatible configurations to join the channel.
Step 4
Example: switch(config-if)# no switchport 4. The forced interface must have the same speed, duplex, and flow control settings as a Layer 3 port. Ensure that you want LACP-based port channels. Example: switch(config...
Configuration Guide - Page 189
...This example shows how to nexus7k-docfeedback@cisco.com
3. Chapter 6 Configuring Port Channels
Configuring Port Channels
Send document comments to configure the port channel interface max-bundle on module 3:
switch# configure terminal switch (config)# lacp max-bundle 3
OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
6-33 show running -config interface...
Configuration Guide - Page 217
... values on this FEX are configured as members of the crucial configuration parameters differ on the two devices. (See the "CFSoE" section on configuring FEX ports. OL-23435-03
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
7-15
Configuration Guide - Page 223
... you configure the port channels without using LACP.
We recommend that you first bring up . It will not cause any problems if the STP enhancements are already configured, but you manually configure the system priority on the vPC peer link devices to ensure that you need not configure these required matched settings. Note You...
Configuration Guide - Page 230
... NX-OS High Availability and Redundancy Guide, Release 5.x, for the local vPC ports. Beginning with Cisco NX-OS Release 5.2(1), you can configure the Cisco Nexus 7000 Series device to restore vPC services when its role priority, and also acts as the master for the local vPC ports. You must save this setting in the startup configuration. On...
Configuration Guide - Page 268
... Membership to the switch. • You have installed the Enterprise Services license for Cisco NX-OS. • You must be familiar with Cisco NX-OS Release 5.2(5) and for later 5.2(x) releases...Settings
Table 8-1 lists the default settings for IP tunnel parameters. Guidelines and Limitations
IP tunnels have the following configuration guidelines and limitations:
• Cisco NX-OS supports...
Configuration Guide - Page 284
...membership of the port is changed using the switchport mode command. interface ethernet slot/port 3. copy running-config startup-config
Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide, Release 5.x
...to set the 802.1Q tunnel port to traverse the Q-in -Q, page 9-9 • Enabling the Layer 2 Protocol Tunnel, page 9-11 • Configuring Global CoS for L2 Protocol Tunnel Ports, ...
Cisco CISCO7204VXR-CH Reviews
We have not received any reviews for Cisco yet.