Cisco CISCO2811-AC-IP - 2811 Integrated Services Router Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco CISCO2811-AC-IP manuals!
Problems with Cisco CISCO2811-AC-IP?
Ask a Question
Free Cisco CISCO2811-AC-IP manuals!
Problems with Cisco CISCO2811-AC-IP?
Ask a Question
Popular Cisco CISCO2811-AC-IP Manual Pages
Hardware Installation Guide - Page 23
Cisco Interface Cards for Cisco Access Routers
Platform Support for Cisco Interface Cards
Table 4
Platform Support for Cisco Interface Cards (continued)
Product Description
Cisco Product ID
Supported on Cisco Routers
16-port asynchronous serial HWIC
HWIC-16A
Cisco 2800 series Cisco 3800 series
T1, E1, and G.703 Multiflex Trunk Voice and WAN Interface Cards
1-port T1 RJ-48 multiflex VWIC...
Hardware Installation Guide - Page 25
... 2600 series Cisco 2800 series Cisco 3600 series Cisco 3700 series Cisco 3800 series Cisco MWR 1941-DC
Cisco MWR 1941-DC
Cisco MWR 1941-DC
Cisco 1751 Cisco 1760 Cisco 2600 series Cisco 2800 series Cisco 3600 series Cisco ICS 7750 Cisco 2800 series2
See Document Voice Interface Cards
Voice Interface Cards
Voice Interface Cards
VWIC-2MFT-T1-DIR, VWIC-2MFT-E1-DIR Installation Instructions VWIC-2MFT...
Hardware Installation Guide - Page 31
... instructions for the Cisco IOS software release you are using > Cisco IOS Software Releases > Technical Documentation > System Message Guides. To find Cisco IOS software release information for a specific feature, access the documents located at Products and Solutions > Cisco IOS Software > Cisco IOS release you are using , access the documents located at Technical Support...
Hardware Installation Guide - Page 49
... blank faceplates for information on the interface card faceplate.
Installing Cisco Interface Cards in Cisco Access Routers
Installing Cisco Interface Cards in Cisco Access Routers
Step 3 Remove the blank faceplates installed over the slot you feel the edge connector seat securely into the connector on the router backplane.
Proceed with the guides in the chassis walls or slot...
Hardware Installation Guide - Page 57
... to laser radiation and do not stare into position. (See Figure 30.) The SFP is locked into open apertures. Installing Cisco Interface Cards in Cisco Access Routers
Installing Other Accessories in Cisco Interface Cards
Installing Other Accessories in Cisco Interface Cards
Certain Cisco interface cards support a variety of the SFP in the closed position for information on the interface...
Hardware Installation Guide - Page 70
... cables are available in DTE format only. Refer to the Cisco Modular Access Router Cable Specifications for 4-Port Serial HWICs
The 4-port serial HWICs use the...Asynchronous modems, if connecting to the instructions in Installing Cisco Interface Cards in Cisco Access Routers. Cables for network end connectors and pinouts of these cables. For instructions on grounding your serial HWIC.
...
Hardware Installation Guide - Page 77
.... Grounding
Ensure that the WIC is installed in the router, the equipment is properly grounded.
ISDN BRI WAN Interface Cards
ISDN BRI S/T WAN Interface Cards
ISDN BRI S/T WIC LEDs
The ISDN BRI S/T WIC LEDs are shown in Table 9.
Setting Jumpers on BRI network modules, see the Cisco Network Modules Hardware Installation Guide. Note For long-distance point-to...
Hardware Installation Guide - Page 81
...on BRI network modules, see the Cisco Network Modules Hardware Installation Guide.
Newer WIC-1B-S/T or WIC-1B-U interface cards can mount in the W1 slot of the LEDs are set appropriately for connecting the WIC to the instructions in Installing Cisco Interface Cards in Cisco Access Routers. Grounding
For instructions on grounding your installation. Cables
Use a straight-through RJ...
Hardware Installation Guide - Page 84
Installing a Cisco ISDN BRI S/T WAN Interface Card
Install the Cisco WIC according to the instructions in Installing Cisco Interface Cards in Cisco Access Routers.
The functions of the LEDs are shown... S/T LL SEE MANUAL BEFORE INSTALLATION
B1 LED B2 LED OK LED
ISDN BRI S/T Leased-Line WIC LEDs
The ISDN BRI S/T leased-line WIC LEDs are described in Table 11. For instructions on B2 channel ...
Hardware Installation Guide - Page 95
... MANUAL BEFORE
INSTALLATION
LP AL CD
LOOP BACK T1 DSU/CSU
DSU CSU
T1
Straight-through RJ-48C-to-RJ-48C cable to the RJ-48C port on power to the router.
The intrabuilding cable must be shielded and the shield must have forgotten your username or password, click Cancel at http://www.cisco.com...
Hardware Installation Guide - Page 96
... and Safety Information • Configuring Cisco Integrated Data Service Unit/Channel Service Unit (DSU/CSU) Modules and
WAN Interface Cards, tech note • "Configuring Serial Interfaces" chapter in the Cisco IOS Interface Configuration Guide for your
Cisco IOS software release • 56K CSU Support for the Cisco Signaling Link Terminal, Cisco IOS Release 12.2(2)T feature
module •...
Hardware Installation Guide - Page 112
... building
39196
Optional microfilters
Cisco router
Customer-Installed Splitter
This scenario is described below and illustrated in Figure 77. • The telephone company has provisioned a single copper pair to be used by both the telephone
(POTS) service and the router with a DSL interface card, so a POTS splitter must be installed. • The splitter is installed by the customer...
Hardware Installation Guide - Page 114
... WIC With IP Unnumbered E0, PPPoA, PPP-PAP, and Manually Configured Local LAN Devices - For more information, see the "Obtaining Documentation, Obtaining Support, and Security Guidelines" section on the Product Documentation DVD. Related Documentation
DSL Interface Cards
Related Documentation
Related documentation is available on Cisco.com or on page 19. Voice and Quality of Service Features...
Hardware Installation Guide - Page 149
... WIC slot other than slot 0 or if more than one WIC-1ENET card can be installed in the router. WIC-1ENET Interface Card Router Processor Requirements
The MPC 860 microprocessor (revision B5 or later) in slot 0 and only one card is addressed as E/1. WIC-1ENET Supported Standards
The IEEE 802.3 Ethernet standards and 10BASE-T Category 3, 4, and 5 UTP cable...
Hardware Installation Guide - Page 178
... MHz for UMTS and HSDPA services HWIC-3G-GSM is the Cisco part number for which the interface card is configured. HWIC-3G-GSM
3G Wireless WAN Interface Cards
REVIEW DRAFT-CISCO CONFIDENTIAL
For regulatory information about the 3G wireless WAN HWIC and supported antennas, see the Cisco Network Modules and Interface Cards Regulatory Compliance and Safety Information. HWIC-3G-GSM
The GSM version...
Cisco CISCO2811-AC-IP Reviews
We have not received any reviews for Cisco yet.