Cisco AS2509-RJ Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco AS2509-RJ manuals!
Problems with Cisco AS2509-RJ?
Ask a Question
Free Cisco AS2509-RJ manuals!
Problems with Cisco AS2509-RJ?
Ask a Question
Popular Cisco AS2509-RJ Manual Pages
Getting Started Guide - Page 3
...), award-winning RF management, quality of services for mobility services such as voice and video, and OEAP support for retail, ...electrical ground before installing the controller. Replace the battery only with Cisco lightweight access points and the Cisco Wireless Control ... with a minimum of a suitably installed ground conductor. The 2504 controllers supports up to the Controller
The 2504 ...
Getting Started Guide - Page 4
...
Null modem serial cable (DB-9 -> RJ-45) to console connection
Cisco WCS software, web user interface
10/100/1000BASE-T MDI cable
Network
Distribution system connection
LAN link for management software connections
WAN or LAN connection to Cisco 2500 Series Wireless Controllers are not currently supported. To best use this guide, you can use straight-through...
Getting Started Guide - Page 5
however the bootloader ensures that supports a RJ-45 connector. Note
It is expected that there will default to unit. Figure 2 Front Panel and LEDs
282249
CONSOLE
CONSOLE
CISCO 2500 Series WIRELESS CONTROLLER
RESET
Model 2504
1
2
3
4
PWR SYS ALM
RESET
1 2 3-4 POE
PWR ALM
SYS
Table 1 Callout
WLC2504 Front Panel Component Descriptions
Port and LEDs
State and ...
Getting Started Guide - Page 9
... controller hardware - If any item is damaged or missing, notify your authorized Cisco sales representative. Required Tools and Information
You will be pre-installed on controller at factory, if selected. • Two Number 6 Phillips pan-head screws for damage. Network, operating system service network, and access point cables as required • Command-line interface (CLI...
Getting Started Guide - Page 10
...password and the configured username and password cannot be hijacked). - Cisco uses an integral TFTP server. Yes is more convenient, but has higher security and works well for downloading operating system software updates... such as 1.1.1.1, used by all Cisco
wireless controller Layer 3 security and mobility managers). • A Cisco wireless controller mobility or RF group name, such as 10.40...
Getting Started Guide - Page 13
... hardware from Cisco.
Statement 378
To mount the controller on page 23. The kit part number is mounted on a shelf or desk, perform the following tasks to complete the installation:
• Connecting the Controller Console Port • Securing the Power Adapter Cable • Connecting to the Network
For configuration instructions about using the CLI setup program...
Getting Started Guide - Page 18
...at the bottom of the controller as shown in Figure 9 with stabilizing devices, install the stabilizers before mounting or servicing the unit in a 19-inch equipment rack, you must take special precautions ... a Rack
To mount the 2504 controller in the rack. Step 6 For configuration instructions about using the CLI setup program, see the "Running the Bootup Script and Power-On Self Test" section ...
Getting Started Guide - Page 24
...display example:
CISCO SYSTEMS WLCNG Boot Loader Version 1.0.15 (Built on Nov 23 2010 at 07:51:36 by cisco) Board Revision...
24 Step 3
Observe the bootup using the CLI screen. OK. Manually update images Enter selection:
If you did not press Esc, the boot ... 0.9 GB (2001888 x 512) Press now to three minutes. Model: 1GB CompactFlash Card Firm: CF B612J Ser#: C181101244A1Yb3A5QNU - Run primary...
Getting Started Guide - Page 25
...: ok Fastpath CPU00: Initializing Timer...done. Num of Cisco Systems, Inc. Starting Switching Services: ok Starting QoS Services: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database...
Getting Started Guide - Page 26
...
26
Starting Policy Manager: ok Starting Authentication Engine: ok Starting Mobility Management: ok Starting Virtual AP Services: ok Starting AireWave Director: ok Starting Network Time Services: ok Starting Cisco Discovery Protocol: ok Starting Broadcast Services: ok Starting Logging Services: ok Starting DHCP Server: ok Starting IDS Signature Manager: ok Starting RFID Tag Tracking: ok Starting...
Getting Started Guide - Page 27
... minutes. Manually update images
Enter selection:
If you did not press Esc, the boot process continues and takes two to access the following menu:
1. Active 2. All rights reserved. Cisco AireOS Version 7.0.114.76 Firmware Version PIC 14.0 Initializing OS Services: ok Initializing Serial Services: ok Initializing Network Services: ok Initializing Licensing Services: ok Starting ARP Services: ok...
Getting Started Guide - Page 28
... CPU01: Core 1 Initialization: ok Fastpath CPU00: Initializing Timer...done. Starting Switching Services: ok Starting QoS Services: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok...
Getting Started Guide - Page 30
... match the switch interface configuration....password to be set to 4.
30 The management interface is no default administrative password, you need to return to the controller.
The default administrative username is the name you want to assign to the previous command line.
Enter the port number of the default router. The VLAN identifier should be assigned to enterprise services...
Getting Started Guide - Page 31
...Wizard Setting
Action
Management Interface DHCP Server IP Address Enter the management interface DHCP server IP address.
All of the mobility group/RF group to which you enter here is assigned to support mobility...to both the mobility group and the RF group, these groups are not identical. Network Name (SSID)
Enter the network name, or service set identifier (SSID). Values are usually also...
Getting Started Guide - Page 37
... reboots and loads the configuration.
Step 2 Step 3
Press and hold the Reset button for at least 3 seconds using a pointed object, such as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your username and password at : http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html Subscribe to the...
Cisco AS2509-RJ Reviews
We have not received any reviews for Cisco yet.