Service Manual
Page 4
... 2-1. Troubleshooting by Service Engineer 1-2. PRINT MODE 4. BLOCK DIAGRAM 2. Serial Number Location 2. Notes on Repair Servicing 3-3. MAINTENANCE 1-1. Operator Call Errors 2-2. Adjustment / Settings (1) Paper feed motor adjustment (2) Grease ... 1-5. REPAIR 3-1. Verification Items (1) Service test print (2) EEPROM information print 4. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Symptom 3. PRINTER TRANSPORTATION Part 2: TECHNICAL REFERENCE 1. Carriage Board (Print Head Connector) PIXMA iP4200 Specifications Special...
... 2-1. Troubleshooting by Service Engineer 1-2. PRINT MODE 4. BLOCK DIAGRAM 2. Serial Number Location 2. Notes on Repair Servicing 3-3. MAINTENANCE 1-1. Operator Call Errors 2-2. Adjustment / Settings (1) Paper feed motor adjustment (2) Grease ... 1-5. REPAIR 3-1. Verification Items (1) Service test print (2) EEPROM information print 4. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Symptom 3. PRINTER TRANSPORTATION Part 2: TECHNICAL REFERENCE 1. Carriage Board (Print Head Connector) PIXMA iP4200 Specifications Special...
Service Manual
Page 17
... the At replacement: paper feed motor are 1. By attaching the tape at the At replacement: specified 2 locations, After the printer unit is 7% or more, also Settings, (5) Service mode, replace the ink absorber kit for details of the logic After ....] 2. Adjustment / Settings, (1) Paper feed motor adjustment.] - Perform the print head alignment in the EEPROM. Apply grease to be loosened. Service test print - Check the ink system function. [See 3.3. Correct the CD / DVD - REPAIR 3-1. Reset the waste ink counter. [See 3.3. EEPROM information print At replacement: ...
... the At replacement: paper feed motor are 1. By attaching the tape at the At replacement: specified 2 locations, After the printer unit is 7% or more, also Settings, (5) Service mode, replace the ink absorber kit for details of the logic After ....] 2. Adjustment / Settings, (1) Paper feed motor adjustment.] - Perform the print head alignment in the EEPROM. Apply grease to be loosened. Service test print - Check the ink system function. [See 3.3. Correct the CD / DVD - REPAIR 3-1. Reset the waste ink counter. [See 3.3. EEPROM information print At replacement: ...
Service Manual
Page 18
...screws of the paper feed motor unit (DO NOT loosen them in other cases). Perform the print head alignment in the user film. (Wipe off any grease mode. Special Notes on Repair Servicing, (3) Printer unit and bottom case unit assembly, for capacitor discharging to the waste ink tube holder. Do .... 1 minute (for details.] - Purge unit: QM22208 secure the waste ink tube to protect the logic board ass'y from damages). - Repair Servicing, (3) Printer unit and bottom case unit assembly.] Platen unit QM2-2202 PR lift shaft ass'y QL2-0936 CL input gear QC1-6213 Timing slit strip film...
...screws of the paper feed motor unit (DO NOT loosen them in other cases). Perform the print head alignment in the user film. (Wipe off any grease mode. Special Notes on Repair Servicing, (3) Printer unit and bottom case unit assembly, for capacitor discharging to the waste ink tube holder. Do .... 1 minute (for details.] - Purge unit: QM22208 secure the waste ink tube to protect the logic board ass'y from damages). - Repair Servicing, (3) Printer unit and bottom case unit assembly.] Platen unit QM2-2202 PR lift shaft ass'y QL2-0936 CL input gear QC1-6213 Timing slit strip film...
Service Manual
Page 34
... section describes the procedures for transporting the printer for returning after repair, etc. 1) In the service mode, press the Power button to finish the mode, and confirm that the paper lifting plate of the sheet feeder unit is raised. 2) Keep the print head and ink tanks installed in the carriage. [See Caution 1 below...
... section describes the procedures for transporting the printer for returning after repair, etc. 1) In the service mode, press the Power button to finish the mode, and confirm that the paper lifting plate of the sheet feeder unit is raised. 2) Keep the print head and ink tanks installed in the carriage. [See Caution 1 below...