Campbell Scientific AVW200 Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific AVW200 manuals!
Problems with Campbell Scientific AVW200?
Ask a Question
Free Campbell Scientific AVW200 manuals!
Problems with Campbell Scientific AVW200?
Ask a Question
Popular Campbell Scientific AVW200 Manual Pages
AVW200-series Vibrating Wire Interfaces - Page 1
INSTRUCTION MANUAL
AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
Revision: 1/14
Copyright © 2008-2014 Campbell Scientific, Inc.
AVW200-series Vibrating Wire Interfaces - Page 3
Batteries, fine-wire thermocouples, desiccant, and other locations, Campbell will return such products by Campbell, and product specific training, is limited to repairing or replacing (at Campbell's option) defective products, which have no warranty. The warranty for installation services performed by Campbell such as programming to customer specifications, electrical connections to be ...
AVW200-series Vibrating Wire Interfaces - Page 4
... Decontamination" form and comply with the requirements specified in countries served by Campbell Scientific, Inc. The following contact information is :
CAMPBELL SCIENTIFIC, INC. Campbell Scientific reserves the right to refuse service on the outside of the problem, an RMA number will be either emailed to repair@campbellsci.com or faxed to process any returns until we receive this number...
AVW200-series Vibrating Wire Interfaces - Page 9
... spectrum radio.
1. Vibrating Wire Measurements are used in programming the older Campbell Scientific interfaces (i.e., AVW1, AVW4, AVW100). Consequently, purchase of incorrect readings due to the AVW200. external noise.
Patent No. 7,779,690 1 The AVW200 significantly reduces and, in frequency based measurements-a complete departure from one major problem-
Likewise, AVW206...
AVW200-series Vibrating Wire Interfaces - Page 11
AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
1.2 Specifications
1.3 Communication
1.3.1 Datalogger
The AVW200 module is designed to work with and complement Campbell Scientific dataloggers, as well as data acquisition products from other manufacturers.
3
AVW200-series Vibrating Wire Interfaces - Page 12
...mode. Our CRBasic dataloggers use the SDI12Recorder instruction and Edlog dataloggers (i.e., CR10X, CR23X) use Instruction 105. You can find Quick Start Guides in Section 3, AVW200() instruction description in Section 6.1, and a programming example in CRBasic supports these wireless interfaces. AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
1.3.1.1 PakBus Protocol/Direct RS-232...
AVW200-series Vibrating Wire Interfaces - Page 13
... the AVW200 CRBasic instruction is described in detail in Campbell Scientific's datalogger support software and can be connected to one CR800 or CR850. Read more ! DevConfig is included. The AVW200 needs to be connected to a computer with one multiplexer.
DevConfig is required. Read more ! AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
1.3.2 Computer...
AVW200-series Vibrating Wire Interfaces - Page 15
...recorded response and analyzes the resulting spectrum to three orders of the taut wire in SDI-12 Mode
FIGURE 1-3. CR10X CR5000 CR23X CR800, CR850 CR1000 CR3000
SDI-12
AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
AVW200 0
AM16/32B
1 2
3
Datalogger MUST Control Multiplexers in a vibrating wire sensor (see FIGURE 2-1) with the following procedure. Network of the resonant...
AVW200-series Vibrating Wire Interfaces - Page 17
... is an invalid voltage supply in the AVW200 CRBasic Instruction. In addition to 0. This indicates to warn the user when there is measured as NAN for measurement diagnostics. 2. Contact Campbell Scientific for the frequency measurement. The bottom graph shows the raw time series data recorded from a vibrating sensor after the AVW200 has applied the fast Fourier transform...
AVW200-series Vibrating Wire Interfaces - Page 25
...vibrating wire sensors. AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
For example, the following AVW200() instructions can be controlled by Datalogger
3.3.1 SDI-12 Communication
AVW200...,2,_60HZ,1,0)
Where, RF401 = configured for non-Campbell Scientific dataloggers.
17 A thorough description of the AVW200() instruction and its parameters is provided in Appendix H.1.2.
...
AVW200-series Vibrating Wire Interfaces - Page 30
.../RF416 Spread Spectrum Data Radio/Modem manual.
4.5 Multiplexer Wiring
Wire the sensors to the multiplexer according to the multiplexer manual. More information about using spread spectrum radios is provided in Appendix C. AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
Wireless communication requires the appropriate spread spectrum radio to be set to PakBus Aware or PakBus...
AVW200-series Vibrating Wire Interfaces - Page 33
...built-in Campbell Scientific's datalogger support software and can also be connected to configure the AVW200 if you are using the 10873 RS-232 cable (shipped with the AVW200) to connect the AVW200 to DevConfig, follow the procedure listed below:
1. DevConfig supports AVW200 configuration, real-time data display, operating system download, and vibrating wire spectrum analysis troubleshoot. To...
AVW200-series Vibrating Wire Interfaces - Page 40
.... Sending an Operating System using a 9-pin serial cable and follow the directions on your computer using DevConfig
32 AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
5.4 Send OS
For most applications, Campbell Scientific does not anticipate that it will need Device Configurator (DevConfig) 1.10 or greater. However, if a new operating system (OS) is connected from the...
AVW200-series Vibrating Wire Interfaces - Page 51
...-to the sensor. TABLE 6-1 shows the specific SDI-12 Command Codes and their returned values. AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
SDIPort SDIAddress SDICommand
The SDIPort parameter is the port to which the SDI-12 sensor is the address of the SDI12 sensor that will be affected by this instruction. Valid addressses are 0 through 9, A through Z, and...
AVW200-series Vibrating Wire Interfaces - Page 76
... interference by Campbell Scientific, Inc.
However, there is connected.
• Consult the dealer or an experienced radio/TV technician for the AVW206, AVW211, and AVW216
• When the antenna cable length exceeds 10 feet
• When use of COAX RPSMA would result in too much signal loss
• When the interface will not...
Campbell Scientific AVW200 Reviews
We have not received any reviews for Campbell Scientific yet.