Brother International BA-10 Support and Manuals
Get Help and Manuals for this Brother International item
View All Support Options Below
Free Brother International BA-10 manuals!
Problems with Brother International BA-10?
Ask a Question
Free Brother International BA-10 manuals!
Problems with Brother International BA-10?
Ask a Question
Popular Brother International BA-10 Manual Pages
Hand Book - English - Page 1
...215; 1 #12
Part name Starter device assembly
Part code S05462-009
2000.7
BA-10, BA-16 1/5
BA−10 BA−16
Chainstitch Button Sewer with Button Feeder Lockstitch Button Sewer with Button Feeder
Specifications
Machine head Use
... arrangement Button feed error detector
Needle
Starter device
Model BA-10
BA-10 CB3-B917A Chainstitch button sewer 1,500 rpm
8 16 32 6 12 24
BA-16 LK3-B448E ...
Hand Book - English - Page 2
Gauge parts list
Feed plate
u159971-001*
Needle hole plate
HS
S40917-001
HT
S40925-001
HU
S52079-001
HV
S52080-001
HW
S52081-001
HX
uS52082-001
*The part indicated with u is a standard part. *The feed plates and needle hole plates are used for B448E and BAS-556. *Refer to B438E Mark II for pattern programs.
BA-10, BA-16 2/5
2000.7
Hand Book - English - Page 3
...2.2
1.0
4
S06687-001
E
2.4
1.0
4
S06687-002
F
2.6
1.2
4 uS06687-003
G
2.8
1.2
4
S06687-004
H
3.0
1.2
4
S06687-005
J
3.2
1.2
4
S06708-001
K
3.4
1.5
4
S06708-002
L
3.6
1.5
4
S06708-003
M
3.2
1.5
4
S06708-004
Button catch plate, blank
Ø (mm) 6 8.5
Part code S06133-001 S06710-001
*The part indicated with u is a standard part.
2000.7
BA-10, BA-16 3/5
Hand Book - English - Page 4
...
Ø 10 mm
Vertical section of button
d
Ø 12 mm
Button upper cover
Ø 12 mm
Ø 16 mm Spacer
Ø 16 mm
Mark
d (mm)
A
9 - 12
B
12 - 16
C
16 - 22
Sorting plate uS05433-000
Part code uS09601-100
S09602-100 S09603-100
(U) S06814-000
Mark A B C
d (mm) 0.4 0.8 0.2
UB S06816-000
Part code uS09604-100 uS09605-100
S13186-100
M S06815-000
*The part indicated...
Hand Book - English - Page 5
...;17
T
2.2 ×17
U
2.7 ×20
*The part indicated with u is a standard part.
Parts code uS07042-001 uS07042-002
S07042-003 S07042-004 S07042-005 S07042-006 S07042-007 S07042-008 S07042-009 S07042-010 S07042-011 S07042-012 S07042-013 S07042-014 S07042-015 S07042-016 S07042-017 S07042-018 S07042-019
2000.7
BA-10, BA-16 5/5
Network Users Manual - English - Page 13
... 0 coincide. sewing patterns
For X-sewing pattern
- 11 -
For Z-sewing pattern 3. Adjustment of the feeder position
X X POWER
ROBOT ON
• OFF
CROSSOVER STITCHES
CD 0 ED
MANUAL
1-57)1., TROUBLE
0
brother BA -10
Crd cZ)
0 CD
For 2-hole button
CD 0
For 4-hole button
(1) Check whether or not the feeder switch Q is completed to return the button transport arm...
Network Users Manual - English - Page 14
... sensor 0. To adjust, turn the power off . Button positioner sensor
O
po O
O
0
0 . 5mm 0 O
I•
POWER
0
❑1•vF
ROBOT ON
(!).)
OFF
CROSS-OVER STITCHES
@0 @
4 tD
MANUAL
-5- 71l,
TROUBLE
brother BA -10
a
1. Loosen screw 0 and move sensor 0 up or down so that button presser 0 contacts button carrier The top of the arrow so that button carrier 0 doe...
Network Users Manual - English - Page 19
...any abnormal noise disappears, and then tighten nut 0. VI.ATOR
ON
OFF 0
0
brother BA-10
1. Press the power switch, and set the vibration bowl switch 0 on. 5.
Lower the vibration solenoid so that the noise ...vibrate properly if these three
parts are not firmly secured. (Use a 1.0 mm thick spring Q for 60 Hz models, and a 0.8 mm thick spring for 50 Hz models.) 4. The bowl will not...
Network Users Manual - English - Page 21
... screw 0, and remove the button. (3) Decrease the button clamp Q opening 1.0 mm to '\ Decvease
1 - 1.5 mm - 1.5 mm
POWER
0
DYrh
ROBOT ON
• OFF
WO*
CROSS-OVER STITCHES
@0 @
# MANUAL
TROUBLE
0
brother BA- 1 0
▪
OC,
1. Button feed sensor
'c%vc(N. Button clamp adjustment
(1) Loosen adjustment screw 0, and insert a button into the button clamp 0, and make sure the...
Network Users Manual - English - Page 25
TROUBLE
brother BA-10
on00000000i OCHOODOC0006
e
gP,22222. 0000000
1.
Control circuit board adjustments VR1 adjustment (carrier motor speed)
ON
S9* CROSSOVER STITCHES
go° C(4`
NBNULL
F-57/1. Trouble lamp Q out
Slow
Trouble lamp Q blinking
Normal
Trouble lamp Q on again to sew.
* Be sure to reset feeder panel switch Q to off .
3. First bet the sewing machine power ...
Network Users Manual - English - Page 29
... spring installed
(60Hz, t1.2; 50Hz, t1.0) 4. Tighten the bolt. 1. Adjust the gap.
1. Adjust. Replace shooter to solenoid
gap
1. Bowl is slow.
3 Button top/bottom not properly aligned.
4 Buttons jam. Firmly connect or replace the
cable. 1. Replace solenoid 1. Page 33
26 17 17 17
1. Improperly adjusted height, width plates
2. ( Trouble shooting Guide )
Vibration bowl
Problem...
Network Users Manual - English - Page 30
...Adjust stop screw.
13
6. Replace motor.
8
function.
2. Loose set screw in use the crossover... guide shaft and button shaft lever screw are not
used crossover stitch
1. Button feeder
Problem
Cause...Replace solenoid.
(OK if resistance is on
positioner sensor
button carrier.
10... screw. (Also tighten the screw rod.)
operation Manual, Page 5
15
9 TROBLE indicator lights
1. Improperly...
Parts Manual - Multi - Page 1
CB3-B917/BA-10
Shit* 3 >flit INNMI]9 .Z i i 7J.t > 7 -f - &Mit
CHAINSTITCH BUTTON SEWER WITH THREAD TRIMMER AND BUTTON FEEDER VERRIEGELUNGSSTICH-KNOPFNAHMASCHINE MIT FADENASSCHNEIDER UND KNOPFZUFUHRUNG MACHINE A COUDRE LES BOUTONS A POINT DE CHAINETTE AVEC COUPE-FILS ET DISTRIBUTEUR DE BOUTONS MAQUINA DE COSER BOTONES A PUNTO CADENETA CON CORTADOR DE HILO Y ALIMENTADOR DE BOTONES
PARTS BOOK ...
Parts Manual - Multi - Page 32
...42-6
SET SCREW 6X6 CAM SUPPOTING (B)ARM, PIN WASHER STOP RING E6 SET SCREW 6X6 CAM SUPPORT STUD SCREW...SET SCREW 6X6 BUTTON TRANSPORT SHAFT SET COLLAR SET SCREW 6X6 BUTTON MOVEMENT ARM (A) SET SCREW 6X6 SCREW 3.57X4 BOLT 6X25 NUT 6 PIN SET SCREW 5.95 CONNECTION SHAFT BUTTON CATCH PLATE ASSEMBLY BOLT 6X50 WASHER SPRING WASHER 2-6
RMKS
- 26 - P1. 7t . 2 7 T - CODE Q'TY
t=ot-r
NAME OF PARTS
1-100...
Parts Manual - Multi - Page 34
... "E-: 7i-In14-4X10 t5irth" 3.,54 /\"*.l ."/3"2-4
5-
N a- RMKS
a- a- CODE Q'TY
t:ii-f
NAME OF PARTS
1-006 1-007 1-008 1-010 1-011 1-012 1-013 1-038 1-040 1-041 1-...SET SCREW 6X6 WORM SET SCREW 5 BOLT 4X10 PLAIN WASHER 4 SPRING WASHER 2-4 THRUST WASHER WASHER BUTTON ALIGNMENT MOTOR GEAR SCREW 3X4 GUIDE... CURCUIT BOARD ASSEMBLY BOARD SET PLATE SUPPORT 6NS WASHER SCREW 4X8 ...
Brother International BA-10 Reviews
We have not received any reviews for Brother International yet.