Bosch 22618 - N/A Impactor 18V Cordless Impact Wrench Support and Manuals
Get Help and Manuals for this Bosch item
Popular Bosch 22618 Manual Pages
Operating Instructions - Page 2
... caught in . Never modify the plug in any adjusting key or wrench before plugging in moving parts.
Personal safety
Stay alert, watch what you are likely to fail and create a hazard to your tool. A moment of flammable liquids, gases or dust. SAVE THESE INSTRUCTIONS
Work area safety
Keep work , the electrical components of electric...
Operating Instructions - Page 3
... cause burns or a fire.
Maintain power tools.
Service
Have your body is suitable for operations different from the power tool before inserting battery pack. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc.
Many accidents are caused by a qualified repair person using only identical replacement parts.
Use clamps or other battery packs...
Operating Instructions - Page 4
...support the workpiece to filter out microscopic particles.
-4- If this situation is unavoidable, disconnect all fuses or circuit breakers feeding this tool. Use thick cushioned gloves and limit the exposure time by taking frequent rest periods.
When installing... torque setting of ...Impact Drivers
Hold tools by insulated gripping surfaces when performing an operation where the cutting tool...
Operating Instructions - Page 5
Charge only Bosch approved rechargeable batteries. Store tool and battery pack in damp or wet environment. The battery liquid is caustic and could cause chemical burns to rain or snow. Place charger on (1) battery charger, (2) battery pack, and (3) product using battery charger, read all instructions and cautionary markings on flat non-flammable surfaces and...
Operating Instructions - Page 6
...or disposed of our commitment to a Skil/Bosch/Dremel Service Center for information on the nickel-cadmium (Ni-Cd) battery indicates Robert Bosch Tool Corporation is part of in a municipal solid waste stream.
...batteries into the trash or the municipal waste stream, which may
result. Robert Bosch Tool Corporation's involvement in this program is voluntarily participating in your area, or ...
Operating Instructions - Page 7
.... SelectorAsettings
I, II, III,
0
Infinitely variablAe selector with off
A
0 Arrow
A
0
Alternating current
A
Direct current
0A
Alternating or direct current
Speed, torque or position settings. This symbol designates that this tool is listed by the Canadian Standards Association. n0 .../min
No load speed
Rotational speed, at no load
Revolutions or reciprocation per second)
W
Watt...
Operating Instructions - Page 8
... Impact Drivers and Impact Wrenches
1/2" SQUARE DRIVE (Models 22612,
22614 & 22618 only)
LOCKING SLEEVE
FIG. 1
VENTILATION OPENINGS
BRUSH COVER
VARIABLE SPEED TRIGGER SWITCH
SWIVEL LIGHTING SYSTEM
BATTERY PACK
FORWARD/REVERSING LEVER & TRIGGER LOCK
RUBBERIZED GRIP
BELT CLIP (Optional Accessory)
BIT AND BIT STORAGE
BATTERY RELEASE TABS
Model number Voltage rating No load speed Impact...
Operating Instructions - Page 9
BM 2609140358 12-05 12/6/05 3:28 PM Page 9
Model number Voltage rating No load speed Impact rate Maximum torque
23609 9.6 V n0 0-2,800/min 0-3,200 950 in-lbs
23612 12 V n0 0-2,800/min 0-3,200 1,050 in-lbs
23614 14.4 V n0 0-2,800/min 0-3,...
Operating Instructions - Page 10
... are not designed for use with impact wrenches.
To install a socket, simply push completely onto output drive.
To remove an accessory, pull locking sleeve forward and simply remove it has been inserted.
WARNING
When the tool is locked in injury to decrease speed (Fig. 1).
FIG. 3
INSERTING AND REMOVING
ACCESSORIES
(Models 23609, 23612, 23614 & 23618 only...
Operating Instructions - Page 11
...tool upside down on clip until it with integrated light source in the knurled thumbwheel. The light beam can be adjusted to your belt. Position 0: The beam is approximately 20 mm. FIG. 5
ATTACHING GEAR BOX COVER (Models 22618...beam is approximately 150 mm. Slide gear box cover into place (Fig. 7).
3. Replace rubber guard to another work area. Position 3: The focus of the beam is shut ...
Operating Instructions - Page 12
...˚C).
3. If you anticipate long periods (i.e.
Before inserting battery pack,
remove protective cap from tool by Bosch will be replaced.
4. To insert battery, align battery and slide battery pack into tool until it is connected to run your local Bosch Service Center. Do not force (Fig. 1). The battery pack accepts only about 80% of its first...
Operating Instructions - Page 15
...fully charged. When you 're charging another battery pack) and slip the battery pack back into the tool handle.
! The purpose of the light is to indicate that the battery is reached, at which ...05 3:28 PM Page 15
CHARGER INDICATORS, SYMBOLS AND MEANING
If the indicator lights are not in tool or
charger, always place protective cap onto
end of battery pack. If the green indicator light is ...
Operating Instructions - Page 16
... to a stop. Therefore, a longer impacting/ tightening action is less as the screw runs down. Drill same diameter as screw head. Always hold the tool firmly and exert light, steady pressure.
... to wood or insulation material. Apply a slight even pressure when driving screws.
-16- Set the screw snugly by sliding over the surface. The screw shank
FASTENING WITH SCREWS
1. The ...
Operating Instructions - Page 17
... 17
clearance hole in the discharged state. WARNING
NO USER SERVICEABLE PARTS INSIDE. SERVICEMEN:
Disconnect tool and/or charger from power
source before using after prolonged storage.
Check both brushes. Rotate brush cap at the rear part of brushes. Only genuine Bosch replacement brushes specially designed for your tool should be in the first piece allows the screw head to...
Operating Instructions - Page 18
...0.75 1.0 2.5 4.0 1.0 2.5 4.0 - --- -
* Screwdriver bit * Carrying case
(* = standard equipment) (** = optional accessories)
-18- CAUTION
Certain cleaning agents and solvents damage
plastic parts. wire extension cords that is capable
of carrying the current necessary for your
tool must be kept clean and free of foreign matter.
Ventilation openings and switch levers must use 3- Grounded...
Bosch 22618 Reviews
We have not received any reviews for Bosch yet.