Type 1 Manual - TL10
Page 3
... tiller on hard or slippery surfaces. 13. Read the operating and service instruction manual carefully. Be thoroughly familiar with electric drive motors or electric starting motors. 4. Preparation 1. Thoroughly inspect the area where the equipment is running . Do not operate the equipment...THESE INSTRUCTIONS FOR ALL DOUBLE-INSULATED APPLIANCES 1) Replacement Parts When servicing use of fire, electric shock, and personal injury, including the following: DANGER: When using electric gardening appliances, basic safety precautions should start to vibrate abnormally, release switch lever to...
... tiller on hard or slippery surfaces. 13. Read the operating and service instruction manual carefully. Be thoroughly familiar with electric drive motors or electric starting motors. 4. Preparation 1. Thoroughly inspect the area where the equipment is running . Do not operate the equipment...THESE INSTRUCTIONS FOR ALL DOUBLE-INSULATED APPLIANCES 1) Replacement Parts When servicing use of fire, electric shock, and personal injury, including the following: DANGER: When using electric gardening appliances, basic safety precautions should start to vibrate abnormally, release switch lever to...
Type 1 Manual - TL10
Page 4
...injury at the rate for best performance and to contain long hair. 5) Use Safety Glasses - Use common sense. Disconnect the appliance from a possible electrical insulation failure within the tool. Keep handles dry, clean and free from work area. 4) Dress Properly - As a result, your tool is ...its op eration. Do not change the equipment plug, extension cord receptacle, or extension cord plug in appliance with two separate layers of electrical insulation or a double thickness of insulation between you are doing. Inspect appliance cord periodically, and if dam aged, have it was ...
...injury at the rate for best performance and to contain long hair. 5) Use Safety Glasses - Use common sense. Disconnect the appliance from a possible electrical insulation failure within the tool. Keep handles dry, clean and free from work area. 4) Dress Properly - As a result, your tool is ...its op eration. Do not change the equipment plug, extension cord receptacle, or extension cord plug in appliance with two separate layers of electrical insulation or a double thickness of insulation between you are doing. Inspect appliance cord periodically, and if dam aged, have it was ...
Type 1 Manual - TL10
Page 6
... bar, tines and hardware bag from the carton. Flanged Hex Nuts (4) 4. Short Hairpin Cotter Pin (1) C ASSEMBLY DANGER: To prevent serious personal injury, do not connect electric extension cord to unit until fully completing assembly. Place a nut (C-2) on each bolt and tighten securely with holes in the frame and insert the short...
... bar, tines and hardware bag from the carton. Flanged Hex Nuts (4) 4. Short Hairpin Cotter Pin (1) C ASSEMBLY DANGER: To prevent serious personal injury, do not connect electric extension cord to unit until fully completing assembly. Place a nut (C-2) on each bolt and tighten securely with holes in the frame and insert the short...
Type 1 Manual - TL10
Page 10
...tiller switch housing prior to clear debris tangled in a dry place. SERVICE INFORMATION All Black & Decker Service Centers are available from spinning. Release switch lever to the yellow page directory under "Tools-Electric" or call : 1-800-544-6986 WARNING: The use ballast tank handle to clean .... Never let any part of the motor housing. If you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you need assistance regarding accessories, please call : 1-800-544-6986 or visit www.blackanddecker.com 10 Note: The tiller...
...tiller switch housing prior to clear debris tangled in a dry place. SERVICE INFORMATION All Black & Decker Service Centers are available from spinning. Release switch lever to the yellow page directory under "Tools-Electric" or call : 1-800-544-6986 WARNING: The use ballast tank handle to clean .... Never let any part of the motor housing. If you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you need assistance regarding accessories, please call : 1-800-544-6986 or visit www.blackanddecker.com 10 Note: The tiller...
Type 1 Manual - TL10
Page 11
... in Latin America. This warranty does not apply to a Black & Decker owned or authorized Service Center for two years against any questions, contact the manager of your warning labels become illegible or are listed under "Tools-Electric" in the packaging, call 1-800-544-6986 for exchanges ...the product to province. The second option is to take or send the product (prepaid) to accessories. Returns should be required.Black & Decker owned and authorized Service Centers are missing, call the local company or see the website for exchanges. FREE WARNING LABEL REPLACEMENT: If...
... in Latin America. This warranty does not apply to a Black & Decker owned or authorized Service Center for two years against any questions, contact the manager of your warning labels become illegible or are listed under "Tools-Electric" in the packaging, call 1-800-544-6986 for exchanges ...the product to province. The second option is to take or send the product (prepaid) to accessories. Returns should be required.Black & Decker owned and authorized Service Centers are missing, call the local company or see the website for exchanges. FREE WARNING LABEL REPLACEMENT: If...