Black & Decker BDEG400 Support and Manuals
Get Help and Manuals for this Black & Decker item
View All Support Options Below
Free Black & Decker BDEG400 manuals!
Problems with Black & Decker BDEG400?
Ask a Question
Free Black & Decker BDEG400 manuals!
Problems with Black & Decker BDEG400?
Ask a Question
Popular Black & Decker BDEG400 Manual Pages
Instruction Manual - Page 1
... ANTES DE USAR EL PRODUCTO. 4-1/2" (114mm) Angle Grinder
INSTRUCTION MANUAL
Catalog Number
BDEG400
Thank you call 1-800-544-6986 from 8 ...Black+Decker purchase, go to 5 p.m. to http://www.blackanddecker.com/instantanswers If you can't find the answer or do not have a question or experience a problem with an agent. Please read before returning this manual for choosing Black+Decker...
Instruction Manual - Page 2
..., clothing and gloves away from heat, oil, sharp edges or moving parts.
Save all WARNINGs and instructions for outdoor use a ground fault circuit interrupter (GFCI) protected supply. ... relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used for carrying, pulling or unplugging the power tool.
Save these instructions
1) Work Area Safety a) Keep work area...
Instruction Manual - Page 3
... will normally break apart during this power tool. Failure to follow all safety warnings, instructions, illustrations and specifications provided with the power tool or these are easier to your power tool serviced by the tool manufacturer. Operations for damage or install an undamaged accessory. For accessories mounted by poorly maintained power tools. Read all...
Instruction Manual - Page 4
.... Accidental contact with a new or replacement wheel, or a new or replacement wire brush installed, hold the tool in direction opposite ...provided, for one minute. Tighten the handle securely. t) The arbor size of hubbed wheels, flanges, backing pads or any other liquid ...precautions are taken. Accessory may make exposed metal parts of tool misuse and/or incorrect operating procedures ...
Instruction Manual - Page 5
... wheel flanges support the wheel thus reducing the possibility of control. Flanges for the higher speed of a smaller tool and may be different from this type of work.
The wire bristles can easily penetrate light clothing and/or skin.
Under some conditions and duration of California to the brush.
Safety Warnings Specific for...
Instruction Manual - Page 6
...Cord Sets
Volts... and may include the
following table shows the correct size to get into a corner or edge because a...depending on the battery pack but may result. The grinder may stand upright on cord length and nameplate ampere rating...insulated)
.../min or rpm....revolutions or reciprocation
per minute
Read instruction manual
.
Vibration caused by the operating action of power and ...
Instruction Manual - Page 7
...brushes. The tool may result. With the guard latch open position. 5. Undetectable damage to repair or replace the guard. D)
Always use the tool and take the tool and guard to a service...tool. Do not operate the grinder with the slots on the ... discs (fig. The BDEG400 is correctly located on ...same guard is closed position and guard installed on the gear case hub. 3. Push...
Instruction Manual - Page 8
...properly seat
the accessory hub before making any adjustments or removing or installing attachments or accessories. 1. OPERATION WARNING: This tool should not ...NOTE: Guard may result in damage to fragment from your Black+Decker dealer as shown (fig. Make sure the wheel has come...and Using Wire Brushes and Wire Wheels Wire cup brushes or wire wheels screw directly on the grinder spindle without ...
Instruction Manual - Page 9
...installing or removing wheels. Apply minimum pressure to the work surface, allowing the tool to 10˚ angle between the tool and work surface before touching the tool to stop . Using wire Cup Brushes and Wire Wheels Wire wheels and brushes...wire brushng paint as it down . • To start the grinder, push the lower part of the wheel radius as when sanding paint. 1. Continuously move ...
Instruction Manual - Page 10
... a forward
and back motion to stop rotating before setting it is difficult to the work area where dust..., drinking or smoking.
See your application. Workers should be replaced daily or whenever the wearer has difficulty breathing. Articles of ...angle between the tool and work surface. 6. Sanding of lead based paint is occurring should contact approximately one inch (25mm) of grinder...
Instruction Manual - Page 11
... replacement parts, contact the Black+Decker location nearest you can also write to us for two years against defective material and workmanship. Whether you may have
11 warrants this product for information at the factory and are beyond the time set for exchanges (usually 30 to 90 days after the sale). This warranty gives you specific...
Instruction Manual - Page 12
... free replacement.
other rights which vary from state to state or province to blow, discontinue
use immediately and have any questions, contact the manager of the service center nearest you have it serviced at a
Black+Decker service center
or authorized servicer.)
• Cord or switch is not intended for warranty information. Joppa Rd. Troubleshooting
Problem...
Black & Decker BDEG400 Reviews
We have not received any reviews for Black & Decker yet.