BenQ V5000i Support and Manuals
Get Help and Manuals for this BenQ item
BenQ V5000i Videos
??????????6000????????????????BENQ V5000i??????? | ?????? | AMA VLOG | CC??
Duration: 16:57
Total Views: 1,770
Duration: 16:57
Total Views: 1,770
BenQ New HT4550i, HT3560, TK860i And V5000i 4K Projector Launched - Explained All Spec, Features
Duration: 2:46
Total Views: 998
Duration: 2:46
Total Views: 998
AVRant Podcast #860 - The Curse of Dr. Toole! (Disney+ ASL, BenQ TK860i, HT3560, HT4550i & V5000i)
Duration: 2:04:21
Total Views: 1,540
Duration: 2:04:21
Total Views: 1,540
Popular BenQ V5000i Manual Pages
RS232 Control Guide - Page 3
Available functions and commands vary by model. Introduction
The document describes how to the command table for product functions.
Check the specifications and user manual of the purchased projector for RS232 commands...
NC
7
RTS
8
CTS
9
NC
3 Follow the procedures to complete the connection and settings first, and refer to control your BenQ projector via RS232 from a computer.
RS232 Control Guide - Page 10
... features differ by projector specification, input sources, settings, etc.. • Commands are working if the standby power is 0.5W or a supported baud rate of the projector is
set. • Uppercase, lowercase...Illegal format. • If a command with correct format is not valid for the projector model, it will echo Unsupported
item. • If a command with correct format cannot be executed...
RS232 Control Guide - Page 20
...High Altitude mode off *Highaltitude=off#
YES
Read
High Altitude mode *Highaltitude=?#
NO
status
Installation Write
Load Lens memory 1 *lensload=m1#
NO
Write
Load Lens memory 2 *lensload=...Only for
service
Color
Write
Tint +
*tint=+#
YES
Calibration Write
Tint -
*tint=-#
YES
Write
Set Tint value
*tint=value#
YES
Read
Get Tint value
*tint=?#
YES
Write
Set BenQ gamma
*...
Installation Guide - Page 4
Projector's remote control
SRteagteumlaetonrtys
ATV dongle (QS02)
Digital Projector
Installation Guide
TV Projector
Installation guide
Warranty card
QR code for support website
Support.BenQ.com
User Manual
PDF
Online Manual V5000i / QS02
Product Support
What You Need To Know Before You Buy Your Laser TV
4
Scan to watch how-to videos.
Installation Guide - Page 14
...manual for starting the projector while in hazardous radiation exposure. • Notice is given to supervise children and to never allow them to stare into the direct beam. Repairing...9 pin x 1
DC 12V trigger x 1 IR receiver x 2
Input terminals
Video signal input Digital HDMI (HDCP 2.2) x 3
Environmental Requirements
Operating temperature 0°C-40...Support.BenQ.com and find your projector.
User Manual - Page 2
... hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose.
Others are trademarks of Texas Instruments. Warranty and Copyright information
Limited warranty
BenQ warrants this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included...
User Manual - Page 3
... the menus ...24 Securing the projector ...25 Switching input signal...25 Shutting down the projector 25 Upgrading firmware ...26 Menu operation ...27 Menu system...27 Basic menu ...32 Advanced menu ...34 Maintenance ...45 Care of the projector...45 Light source information 45 Troubleshooting ...48 Specifications ...49 Projector specifications 49 Dimensions...50 Timing chart ...50
Table of...
User Manual - Page 16
...
• The setup wizard during the projector initial setup
P
• The Screen Adjustment menu in the Basic settings
menu
• The Installation > Screen Adjustment menu in the
Advanced settings menu.
To correct... correct keystoning at the right side of the image, use / to open the Manual Focus menu and
then use .
16 Positioning your eyes. Adjusting the projected image
...
User Manual - Page 26
...from the Information > Firmware Upgrade menu. 2. Go to BenQ website and enter Product page > Support > Software to the Advanced menu > System > Firmware Upgrade menu, and press OK.
5. Call BenQ service center to provide the version number and verify the projector is finished.
26 Operation
Check and write down your firmware version from firmware compatibility problem.Avoid turning on the...
User Manual - Page 27
.... If there is no equipment connected to the signal type selected and the projector model you are available when the projector detects at least one valid signal.
Basic Menu
Main... Auto Screen Fit Manual Screen Fit
Detected Resolution Source Picture Mode Light Source Mode 3D Format Color System Dynamic Range Light Source Usage Time Firmware Version 3D Format Service Code
Options Bright Living ...
User Manual - Page 32
...is available for selection.
• HDR10+: This mode is only available when HDR10+ content is set to Game, it will automatically switch to HDR Game.
• FILMMAKER MODE (HDR): Delivers...a small amount of the projected image.
In game mode, the projector automatically optimizes the input lag to bring up 3D effects when watching 3D content. This mode is
suitable for environments where...
User Manual - Page 33
...Recalls the settings customized based...firmware version of the
screen and adjusts the image to the input source. YUV444-16bit-BT2020. • Dynamic Range: Shows the picture dynamic range, e.g.
Menu operation 33 This menu allows you to use the , , , and buttons on how to display better picture quality. Adjusts the level of your projector. • Service Code...also manually select ...
User Manual - Page 39
...contents. to save
This projector supports playing three-dimensional (3D) ... (with 3D Blu-ray discs), and so on your input signal source.
• Auto: Scales an image proportionally ... video devices to the projector, wear the BenQ 3D glasses and make sure the power is...default setting is on to set the image's aspect ratio depending on .
however, this function to light, heart problems,...
User Manual - Page 52
...model
• XXXX: Support auto-detect 3D and manually set 3D format (HDMI receiver or scaler down scaling 4K content to EDID file and VGA graphics card limitations. It is also workable.
• XXX: Support manually set 3D format.
• XX: Support manually set...
XXXX XXXX
XXXX XXXX
XXXX
52 Specifications
3D sideby-side
3D overunder
3D Field Sequential
Resolution
Mode
Refresh
H-
User Manual - Page 53
Specifications 53
If source can output CEA861 720p/1080p and color space is RGB with 3D info frame then 3D auto detect function is also workable.
• XXX: Support manually set 3D format. • XX: Support manually set 3D format. • XXXX: Support auto-detect 3D and manually set 3D format (HDMI receiver or scaler down scaling 4K content to 1080p).
BenQ V5000i Reviews
We have not received any reviews for BenQ yet.