Installation Manual
Page 2
...: The rear panel ports and their locations may have four rear USB 2.0 ports) 6. HDD LED 7. Power button 8. VGA port ( ) 4. USB 2.0 ports ( ) (some models only) 1 2 7 4 3 8 5 6 9 Installation manual LAN (RJ-45) port ( ) 7. Reset button NOTE: *Some models may vary, depending on the model of the following ports: • E-SATA port ( ) • Serial (COM1...
...: The rear panel ports and their locations may have four rear USB 2.0 ports) 6. HDD LED 7. Power button 8. VGA port ( ) 4. USB 2.0 ports ( ) (some models only) 1 2 7 4 3 8 5 6 9 Installation manual LAN (RJ-45) port ( ) 7. Reset button NOTE: *Some models may vary, depending on the model of the following ports: • E-SATA port ( ) • Serial (COM1...
Installation Manual
Page 3
Floppy disk drive bay 4. Hard disk drive bay 5. Installation manual Power supply unit 6. One of the following audio ports configurations: • 6-channel • 8-channel Refer to the system User Guide for details. Internal components 5 6 7 8 2 3 4 1 1. English 9. ASUS motherboard* 8. Chassis fan slot 7. Expansion slot metal brackets NOTE: *Refer to the configuration table in the User Guide for motherboard details. Front panel cover 2. 5.25-inch optical drive bays 3.
Floppy disk drive bay 4. Hard disk drive bay 5. Installation manual Power supply unit 6. One of the following audio ports configurations: • 6-channel • 8-channel Refer to the system User Guide for details. Internal components 5 6 7 8 2 3 4 1 1. English 9. ASUS motherboard* 8. Chassis fan slot 7. Expansion slot metal brackets NOTE: *Refer to the configuration table in the User Guide for motherboard details. Front panel cover 2. 5.25-inch optical drive bays 3.
Installation Manual
Page 4
... tabs on the rear panel. 2. If the voltage supply in your area is 200‑240 V, set aside. 3 4 Air duct 1 23 4 1 4 3 2 Chassis tab holes 3 Installation manual Removing the side cover and front panel assembly 1. Swing the front panel assembly to 115 V. Locate the front panel assembly hooks, then lift them until...
... tabs on the rear panel. 2. If the voltage supply in your area is 200‑240 V, set aside. 3 4 Air duct 1 23 4 1 4 3 2 Chassis tab holes 3 Installation manual Removing the side cover and front panel assembly 1. Swing the front panel assembly to 115 V. Locate the front panel assembly hooks, then lift them until...
Installation Manual
Page 5
... the CPU over the socket, making sure that the gold triangle is released from the load plate window to a 135º angle. 4. Alignment key A Installation manual B To prevent damage to the left (B) until it is on the motherboard. 2. Gold triangle mark 6. English Installing a CPU Installing an Intel® Pentium® 4 CPU...
... the CPU over the socket, making sure that the gold triangle is released from the load plate window to a 135º angle. 4. Alignment key A Installation manual B To prevent damage to the left (B) until it is on the motherboard. 2. Gold triangle mark 6. English Installing a CPU Installing an Intel® Pentium® 4 CPU...
Installation Manual
Page 6
... lever to secure the CPU. 1 2 3 CAUTION: Incorrect installation of the installed CPU, making sure that the four fasteners match the holes on the motherboard. A B B A 1 1 Installation manual Install the CPU to secure the heatsink and fan assembly in place. 3. Push down two fasteners at a time in place, connect the CPU fan cable...
... lever to secure the CPU. 1 2 3 CAUTION: Incorrect installation of the installed CPU, making sure that the four fasteners match the holes on the motherboard. A B B A 1 1 Installation manual Install the CPU to secure the heatsink and fan assembly in place. 3. Push down two fasteners at a time in place, connect the CPU fan cable...
Installation Manual
Page 7
... retention module base until it clicks in this connector. CPU fan Retention bracket lock Retention bracket 1 2 4 3 5 CPU fan connector CPU heatsink Retention module base Installation manual Place the heatsink on top of the retention bracket to connect the CPU fan connector! NOTE. otherwise you fail to the module retention module base...
... retention module base until it clicks in this connector. CPU fan Retention bracket lock Retention bracket 1 2 4 3 5 CPU fan connector CPU heatsink Retention module base Installation manual Place the heatsink on top of the retention bracket to connect the CPU fan connector! NOTE. otherwise you fail to the module retention module base...
Installation Manual
Page 8
English Installing a DIMM 1. Remove the metal cover opposite 2. Replace the metal bracket lock. 4 Installation manual Do not force a DIMM into a socket to the 3 slot, then press the card firmly until the retaining clips snap inward. the slot that it fits ...
English Installing a DIMM 1. Remove the metal cover opposite 2. Replace the metal bracket lock. 4 Installation manual Do not force a DIMM into a socket to the 3 slot, then press the card firmly until the retaining clips snap inward. the slot that it fits ...
Installation Manual
Page 9
... upright, then remove the lower 3.5" drive bay metal plate cover. 2. Secure the floppy disk drive with the holes on both sides of the bay. 4. Installation manual 2 3 B A 3 2 B A 3 2 English Installing storage drives Optical drive 1. Hard disk drive 1. Place the chassis upright, then remove the upper 3.5" drive bay metal plate cover. 2. Insert the hard...
... upright, then remove the lower 3.5" drive bay metal plate cover. 2. Secure the floppy disk drive with the holes on both sides of the bay. 4. Installation manual 2 3 B A 3 2 B A 3 2 English Installing storage drives Optical drive 1. Hard disk drive 1. Place the chassis upright, then remove the upper 3.5" drive bay metal plate cover. 2. Insert the hard...
Installation Manual
Page 10
... place. 3. To do this: 1. Push the bay cover inward, then set it to the direction of the drive. Air duct 2 1 5 4 2 1 5 3 Chassis tab holes 1 2 2 10 Installation manual Removing the bay covers and reinstalling the front panel assembly and side cover If you removed earlier. Press the locks outward to remove the 3.5" drive...
... place. 3. To do this: 1. Push the bay cover inward, then set it to the direction of the drive. Air duct 2 1 5 4 2 1 5 3 Chassis tab holes 1 2 2 10 Installation manual Removing the bay covers and reinstalling the front panel assembly and side cover If you removed earlier. Press the locks outward to remove the 3.5" drive...