User Guide
Page 26
... manually after the Windows installation is Already Installed on the Device Manager tab. 4-4 Double- During a normal Windows 95/98 installation, the SCSI Card 2930CU is detected in either Installing the Driver When Windows 95 is Already Installed on page 4-4 or Installing the Driver When Windows 98... is complete. click System, then click on page 4-7. Installing Drivers Installing the Driver When Installing Windows 95/98 The Ultra SCSI driver is Already Installed To update or install the driver 1 Start Windows 95. 2 Click Start, point to Settings, then click Control Panel.
... manually after the Windows installation is Already Installed on the Device Manager tab. 4-4 Double- During a normal Windows 95/98 installation, the SCSI Card 2930CU is detected in either Installing the Driver When Windows 95 is Already Installed on page 4-4 or Installing the Driver When Windows 98... is complete. click System, then click on page 4-7. Installing Drivers Installing the Driver When Installing Windows 95/98 The Ultra SCSI driver is Already Installed To update or install the driver 1 Start Windows 95. 2 Click Start, point to Settings, then click Control Panel.
User Guide
Page 58
...transfer rate the SCSI card supports. If one SCSI device does not support SCSI parity, change this setting enabled unless any SCSI device connected to Disabled. Configuring the SCSI Card 2930CU with SCSISelect I SCSI Parity Checking-...When set to Enabled, initiates synchronous data transfer negotiation (Sync Negotiation) between the ends of the SCSI bus.) You can also disable the terminators by setting Host Adapter Termination to Disable. Leave this setting to the SCSI card does not support synchronous negotiation. Adaptec recommends that you have an Ultra...
...transfer rate the SCSI card supports. If one SCSI device does not support SCSI parity, change this setting enabled unless any SCSI device connected to Disabled. Configuring the SCSI Card 2930CU with SCSISelect I SCSI Parity Checking-...When set to Enabled, initiates synchronous data transfer negotiation (Sync Negotiation) between the ends of the SCSI bus.) You can also disable the terminators by setting Host Adapter Termination to Disable. Leave this setting to the SCSI card does not support synchronous negotiation. Adaptec recommends that you have an Ultra...
User Guide
Page 59
... that has multiple LUNs is supported. I Boot Only-Only the removable-media drive designated as the boot drive is not Ultra SCSI, select a transfer rate of 20.0. I Send Start Unit Command-When set it to No for example, CD-ROM drives) are supported by software drivers and do ... Disconnection-When set to Enabled if you can set to Yes, sends the Start Unit Command to disconnect from the SCSI bus. Determines which removable-media drives are controlled by the SCSI card BIOS. I Support Removable Disks Under BIOS as a hard disk drive. Advanced Configuration Options Note: Do not ...
... that has multiple LUNs is supported. I Boot Only-Only the removable-media drive designated as the boot drive is not Ultra SCSI, select a transfer rate of 20.0. I Send Start Unit Command-When set it to No for example, CD-ROM drives) are supported by software drivers and do ... Disconnection-When set to Enabled if you can set to Yes, sends the Start Unit Command to disconnect from the SCSI bus. Determines which removable-media drives are controlled by the SCSI card BIOS. I Support Removable Disks Under BIOS as a hard disk drive. Advanced Configuration Options Note: Do not ...
User Guide
Page 69
... connector. Maximum Cable Length Data Transfer Rate Maximum Devices Supported1 3 m (9.8 ft) Fast SCSI 8 (10 MB/sec) 3 m (9.8 ft) Ultra SCSI 4 (20 MB/sec for 8 bit, 40 MB/sec for 16-bit) 1.5 m (4.9 ft) Ultra SCSI2 6 m (19.7 ft) 5 MB/sec 8 (asynchronous or synchronous) 1 Including the SCSI card. 2 Ultra SCSI data transfer rates do not currently support more than eight peripherals per...
... connector. Maximum Cable Length Data Transfer Rate Maximum Devices Supported1 3 m (9.8 ft) Fast SCSI 8 (10 MB/sec) 3 m (9.8 ft) Ultra SCSI 4 (20 MB/sec for 8 bit, 40 MB/sec for 16-bit) 1.5 m (4.9 ft) Ultra SCSI2 6 m (19.7 ft) 5 MB/sec 8 (asynchronous or synchronous) 1 Including the SCSI card. 2 Ultra SCSI data transfer rates do not currently support more than eight peripherals per...