AEG LF8E8436BI Support and Manuals
Get Help and Manuals for this AEG item
View All Support Options Below
Free AEG LF8E8436BI manuals!
Problems with AEG LF8E8436BI?
Ask a Question
Free AEG LF8E8436BI manuals!
Problems with AEG LF8E8436BI?
Ask a Question
Popular AEG LF8E8436BI Manual Pages
User Manual - Page 1
LF8E8436BI
EN User Manual Washing Machine
USER MANUAL
User Manual - Page 2
..., trouble shooter, service and repair information: www.aeg.com/support
Register your product for better service: www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance: www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts. PRODUCT DESCRIPTION 7 4. DIAL AND BUTTONS 21 8. BEFORE FIRST USE 29 11.
CONTROL PANEL 19 7. SETTINGS...28...
User Manual - Page 4
...using the new supplied hose sets, or other similar accommodation where such use does not exceed (average) domestic usage levels.
• Do not change the specification of this appliance. •... carpet, mat, or any floor covering. • The appliance must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard. • Before ...
User Manual - Page 6
... suitable for all models. • Concerning the lamp(s) inside this product and spare part lamps sold separately:...firmware including reset software, door, door hinge and seals, other greasy substances. Risk of injury or suffocation.
• Disconnect the appliance from the laundry.
2.5 Service
• To repair the appliance contact the Authorised Service Centre. Contact the Authorised Service...
User Manual - Page 14
...
min. 560 mm
min. 820 mm
16-22 mm
This appliance has been designed to be built into the appliance from the sink.
Contact the service centre for the other drain hose and the extension.
5.7 Building in the spigot and tighten it with the supplied cable tie
L. max.600 mm
To...
User Manual - Page 15
...be : • width min. 595 - ENGLISH 15
The appliance is originally pre set for the assembly of a cupboard door opening from right to the lower hole of the bottom plate.
Factory pre... setting The appliance is also equipped with appliance building in the drawing. Before proceeding with an adhesive...
User Manual - Page 16
....aeg.com
Reversibility of
the hole to countersink the upper hinge.
If the cupboard door has to be at the same
height of the hinge
supports M with magnet is recommended to the furniture
correctly.
Cupboard door preparation
For countersinking the door, it
is on the hinge...
User Manual - Page 17
... the inner side of cupboard door is parallel with the appliance edge and to the hinge supports on the appliance by means of the two supplied screws B.
ENGLISH 17
16-22 mm Ø 35 mm
Set the position of the door. The hinges will be adjusted to the door by means of...
User Manual - Page 18
... in the first
step.
Make sure that your domestic electrical installation can be easily accessible after installing the appliance. Connect the appliance to install this appliance, contact our Authorised Service Centre. The power supply cable must be only installed when the appliance installation is pre set for damage or injury through failure to the mains socket.
Open...
User Manual - Page 20
... Delay time (e. g. ).
• Cycle end (
).
• Warning code (e.g.
).
• Error indicator (
).
• Indication of total operating hours of the selected programme... (e. Steam phase indicator.
This is a recommendation to the
'Operating hours counter' section in the 'Settings' paragraph for
more laundry. Spin phase is still possible to "The ProSense System load de‐...
User Manual - Page 21
...appliance empties the water out automatically after several minutes to reduce the energy consumption, you to set incompatible options/ functions.
7.2 On/Off
Press this option to activate the appliance again. The... option/function can decrease the default spin speed. For more water for more details.
Set this button for use at night time when The washing programme ends with water in the...
User Manual - Page 35
...detergents or We recommend that the items are available. manually redistribute the load so that you wash them separately for...parts.
12.3 Detergent type and quantity
The choice of detergent and use of the water used.
• Follow the instructions...coloured items together.
• Some coloured items can cause balance problems with the spin phase leading to excessive vibration.
Use a ...
User Manual - Page 43
....
• Make sure that the water tap is overloaded, remove some problems, the display shows an alarm code and the
Start / Pause button may flash continuously:
If the appliance is...of the water inlet hose is correct. • Set the drain programme if you set a programme without drain
phase. • Set the drain programme if you set an option which ends with water prop‐
erly....
User Manual - Page 44
...tion". Clean the filter, if
necessary. Refer to "Installation instruc‐
mediately.
The appliance fills with the washing ...problem continues, contact the Authorised Service Centre. Contact the Authorised Service Centre. If the display shows other alarm codes, deactivate and activate the appliance. The mains supply is unstable.
• Wait until mains supply is set, cancel the setting...
User Manual - Page 45
... detergent).
• Make sure you set the correct temperature. • Decrease the laundry load. The necessary data for the service centre are re‐ moved. Refer to open it using the emergency unlock function.
gramme execution. If necessary, wait until they cool down. If you need to "Installation instruction".
• Make sure that you...
AEG LF8E8436BI Reviews
We have not received any reviews for AEG yet.