AEG LF7C8636BI Support and Manuals
Get Help and Manuals for this AEG item
View All Support Options Below
Free AEG LF7C8636BI manuals!
Problems with AEG LF7C8636BI?
Ask a Question
Free AEG LF7C8636BI manuals!
Problems with AEG LF7C8636BI?
Ask a Question
Popular AEG LF7C8636BI Manual Pages
User Manual - Page 1
LF7C8636BI
EN User Manual Washing Machine
USER MANUAL
User Manual - Page 2
... USE...32 12. TROUBLESHOOTING 44 15. When contacting our Authorised Service Centre, ensure that help make life simpler - INSTALLATION...8 6. features you for choosing this AEG product. Please spend a few minutes reading to :
Get usage advice, brochures, trouble shooter, service and repair information: www.aeg.com/support
Register your product for better service: www.registeraeg.com...
User Manual - Page 4
... new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. • Old hose sets must be connected...environment.
• This appliance may be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an...) domestic usage levels.
• Do not change the specification of this appliance. • The appliance maximum load is...
User Manual - Page 6
... and sensors, software and firmware including reset software, door, door hinge and seals, other drain hose and the extension.
• Make sure that not all spare parts are relevant for 10 years after the installation.
2.4 Use
WARNING! It can damage rubber parts of these spare parts are only available to professional repairers, and that there is...
User Manual - Page 14
... pipe in
min.600 mm
min. 560 mm
min. 820 mm
16-22 mm
This appliance has been designed to maximum 400 cm. Contact the service centre for the other drain hose and the extension.
5.7 Building in the room
L
wall and tighten it with the measures 50 x 50 mm.
Make sure...
User Manual - Page 16
... the cupboard door Carry out the cupboard door reversibility before the appliance is originally pre set for the assembly of a cupboard door opening from the counter is 10mm. max.... it.
5.9 Preparation and assembly of the cupboard door
The dimensions of the bottom plate. Factory pre setting The appliance is built in completely.
16 www.aeg.com
~10mm
2. Adjust the anti-tilting device so...
User Manual - Page 17
...call a professional. Countersink the holes.
449 mm
12,5 - 14 mm
22±1,5 mm
595-598 mm Set the position of the hole Y should be opened from
N
left to the furniture correctly.
y
x y
16...-22 mm Ø 35 mm
Cupboard door preparation
For countersinking the door, it is on the hinge support. O
M N
O
Make sure that the plate with the magnetic plate N and
M
lower plate O.
The ...
User Manual - Page 18
... in the first
step. Open the cupboard door and screw the
counter-magnet D (steel disk + rubber
ring E) with the appliance edge and to the hinge supports on the appliance by means
A
of the four supplied screws A.
N
For a correct closure:
1.
Position the screw C and the counter- Counter-magnet
The appliance is pre...
User Manual - Page 19
... the furniture, near the front panel taking into account any responsibility for damage or injury through failure to install this appliance, contact our Authorised Service Centre. The power supply cable must be only installed when the appliance installation is complete, to an earthed socket. Check that they are compatible with the above safety precaution.
User Manual - Page 21
...Spin phase is still possible to the
'Operating hours counter' section in the 'Settings' paragraph for
more laundry. Anti-crease phase indicator.
The spin area: Spin ...Temperature indicator . Drum clean indicator. g. ).
• Cycle end (
).
• Warning code (e.g.
).
• Error indicator (
).
• Indication of total operating hours of the selected programme. The digital ...
User Manual - Page 22
... can decrease the default spin speed.
When the display shows the indicators , the appliance does not heat the
water.
7.5 Spin
When you may need to set incompatible options/ functions.
7.2 On/Off
Press this option you can exclude another one, in Daily Use chapter.
7.3 Programme dial
For selecting the desired washing programme...
User Manual - Page 37
...instructions on garments near the appliance as it is corrosive to the plastic parts.... Remove the
hooks and put the items in the appliance. b. press the Start / Pause button. Do not spray stain remover on the laundry care labels.
• Do not wash white and coloured items together.
• Some coloured items can cause balance problems... sufficient. manually redistribute the... you set a...
User Manual - Page 45
...connection of the drain hose is correct. • Set the drain programme if you set a programme without drain
phase. • Set the drain programme if you set an option which ends with water prop‐ ...and cleaning'.
Problem
Possible solution
•
The appliance does •
not fill with
water in the tub. WARNING! Refer to the tables).
ENGLISH 45
14.1 Alarm Codes and Possible ...
User Manual - Page 46
the appliance. Contact the Authorised Service Centre. If the display shows other alarm codes, deactivate and activate the appliance. In case of the knob on the selected programme.
This problem may be caused by balance problems. Switch the appliance off and on again.
The
water and drains im‐
hose may be positioned too low...
User Manual - Page 47
... special products to "Installation instruction".
• Make sure that the packaging and/or the transit bolts are not satisfactory.
• Increase the detergent quantity or use the correct detergent and the correct quantity of the appliance. The washing results are re‐ moved.
If the problem occurs again, contact the Authorised Service Centre. If...
AEG LF7C8636BI Reviews
We have not received any reviews for AEG yet.