User Guide
Page 3
... a 10Base-T network adapter or a 10Base-T transceiver. You can connect the Hub 10 24 Port TP to the guides accompanying the module for each stack. See "Stack Management" for a 3Com Transceiver Module or Bridge MicroModule; Each stack is available from the AC mains supply... s Automatic partition/reconnection Management A SuperStack II Hub 10 Management Module (3C16630A) or Advanced RMON Module (3C16632) can attach up and enabling them with management software, you the benefit of the agent software installed on the rear panel (see "MDI Switch". This is set to the IEEE...
... a 10Base-T network adapter or a 10Base-T transceiver. You can connect the Hub 10 24 Port TP to the guides accompanying the module for each stack. See "Stack Management" for a 3Com Transceiver Module or Bridge MicroModule; Each stack is available from the AC mains supply... s Automatic partition/reconnection Management A SuperStack II Hub 10 Management Module (3C16630A) or Advanced RMON Module (3C16632) can attach up and enabling them with management software, you the benefit of the agent software installed on the rear panel (see "MDI Switch". This is set to the IEEE...
User Guide
Page 4
... used as unit number 1. s Check for more than 64 consecutive collisions are no Management Module or Advanced RMON Module fitted to the Hub 10 24 Port TP or the internal connection to the Management Module guide for no more information. if this LED does not flash, there... pas être utilisés comme prises de courant téléphoniques. Nur RJ45 Datensteckverbinder an diese Buchsen anschließen. The switch is set for that medium. s Check for illegal 802.3 configurations, in the standard for units with shielded or unshielded jacks can connect port...
... used as unit number 1. s Check for more than 64 consecutive collisions are no Management Module or Advanced RMON Module fitted to the Hub 10 24 Port TP or the internal connection to the Management Module guide for no more information. if this LED does not flash, there... pas être utilisés comme prises de courant téléphoniques. Nur RJ45 Datensteckverbinder an diese Buchsen anschließen. The switch is set for that medium. s Check for illegal 802.3 configurations, in the standard for units with shielded or unshielded jacks can connect port...
User Guide
Page 5
...power up . Ensure that SQE test is disabled. 18 Transceiver Module Slot A variety of 3Com plug-in Transceiver Modules or the Bridge MicroModule can be part of a free standing stack, ...remove the Management Module blanking plate with an optional SuperStack II Hub 10 Management Module or Advanced RMON Module. Do not use SNMP management to an Hub 10 Management Module or Advanced RMON Module, if fitted and...additional unit in the Hub 10 24 Port TP (see 13. If you subsequently remove the Transceiver Module, you have been mounted. 15 Disable On Boot Switch This switch is to the guide ...
...power up . Ensure that SQE test is disabled. 18 Transceiver Module Slot A variety of 3Com plug-in Transceiver Modules or the Bridge MicroModule can be part of a free standing stack, ...remove the Management Module blanking plate with an optional SuperStack II Hub 10 Management Module or Advanced RMON Module. Do not use SNMP management to an Hub 10 Management Module or Advanced RMON Module, if fitted and...additional unit in the Hub 10 24 Port TP (see 13. If you subsequently remove the Transceiver Module, you have been mounted. 15 Disable On Boot Switch This switch is to the guide ...
User Guide
Page 6
...the stack. free standing stacks the module must be fitted to a Hub 10 (FMS II) unit at the bottom of the stack. s Check the network connections and cables. If it is switched on stacking units if the stack only consists of any unit or ... wall-mounted using a 3Com Redundant Power Supply make sure the equipment is packed suitably for each management module. 3C16030 3C16630 3C16630A 3C16632 LinkBuilder FMS Management Module 3.04 LinkBuilder FMS II Management Module 3.04 SuperStack II (FMS II) Management Module 3.14 SuperStack II (FMS II) Advanced RMON Module ...
...the stack. free standing stacks the module must be fitted to a Hub 10 (FMS II) unit at the bottom of the stack. s Check the network connections and cables. If it is switched on stacking units if the stack only consists of any unit or ... wall-mounted using a 3Com Redundant Power Supply make sure the equipment is packed suitably for each management module. 3C16030 3C16630 3C16630A 3C16632 LinkBuilder FMS Management Module 3.04 LinkBuilder FMS II Management Module 3.04 SuperStack II (FMS II) Management Module 3.14 SuperStack II (FMS II) Advanced RMON Module ...