3Com 3C16371 - LinkBuilder FMS - Hub Support and Manuals
Get Help and Manuals for this 3Com item
View All Support Options Below
Free 3Com 3C16371 manuals!
Problems with 3Com 3C16371?
Ask a Question
Free 3Com 3C16371 manuals!
Problems with 3Com 3C16371?
Ask a Question
Popular 3Com 3C16371 Manual Pages
User Guide - Page 5
... and Memory A-2 Cable Pin-Outs A-3 Protocol Addresses A-5
IPX Addresses A-5 IP Addresses A-5 Obtaining a Network Number A-6
B TECHNICAL SUPPORT
On-line Technical Services B-1 3Com Bulletin Board Service B-1 World Wide Web Site B-2 ThreeComForum on CompuServe B-2 3ComFacts Automated Fax Service B-3
Support from Your Network Supplier B-3 Support from 3Com B-4 Returning Products for Repair B-5
User Guide - Page 8
...from 3Com's bulletin board services if required. This guide does not:
s Show you how to other manuals for this guide, follow the release notes.
See "Other Useful Publications" on page ix. s How to install SuperStack ... such as
Transcend WorkGroup Manager for reference purposes. viii ABOUT THIS GUIDE
situations. s How to set up and use the information given for Windows. If you will...
User Guide - Page 9
...management products called Transcend.
Appendix A
Information about interpreting statistics. Troubleshooting information.
Appendix C
Information about obtaining technical support and 3Com repair Appendix B services. Chapter 2
Information about RMON Support.
DUA2785-0AAA0X). Appendix D
Information about how to install the Module into your Chapter 3 SuperStack II Hub 10...
User Guide - Page 25
...set the character size (8), stop bit (1) and parity (none) settings of the emulator to work with the VT100 management interface. Consult the operator manuals ...running SLIP (Serial Line Internet Protocol). The section "Setup" on its baud rate to that of the terminal ...manufacturer and model. Refer to "IP Addresses" on page 3-6 for terminals will depend on page 3-10 explains how to set up the ...
User Guide - Page 27
...update it. Check the user manual supplied with your BootP server and "Setup" on page 3-10 for details of how to get the best out of the stack, and the Default Router address if necessary, if you know them.
The use of 3Com...you may use the VT100 interface to set up parameters including trap addresses, perform ... on your Telnet application is installed correctly at the management station....
User Guide - Page 28
.... Refer to the manual accompanying your chosen network manager for the SuperStack II Hub 10 Series is available free on page 3-13). Use the VT100 interface to set up parameters including trap...or IPX address of the stack, and the Default Router address if necessary, or use the appropriate MIB file. 2-12 CHAPTER 2: INSTALLATION AND SETUP FOR MANAGEMENT
To manage the stack with an SNMP ...
User Guide - Page 40
... is not installed before sending out requests for data until one of the network for IPX addressing. For a class C address, 255.255.255.0 (the default setting) is received, s or, you enter the address manually. If you...IP address, the SubNet Mask, and the Router IP address from the stack that Flow Control is not set to XON/XOFF (see "Serial Port Setup" on sending requests for the data.
User Guide - Page 47
... implementation, Specialist has the same rights as Transcend WorkGroup Manager for Windows. This level of problems on your network, we suggest that you require, then move the cursor to the system ...it is important or secret data on your network. DUA1663-0BAA03
Remember that you change the default password (see "Edit User" on page 3-21) for the security access level. You may wish...
User Guide - Page 61
... need to quote this number to your supplier's technical support service in the event of the unit. DUA1663-0BAA03 Unit Type This field displays the product name or specification of the unit at the time you have selected.
It shows how the unit has been set up, and the physical configuration of the chosen...
User Guide - Page 62
...the Port Setup screen) is currently set to a unit at the same time.
For an existing unit, or replacement unit ...support service. s All Ports Disabled -
the built-in the Port Setup screen is active. At power up . You must NOT connect both the redundant backup power supply and mains power to Enabled. The boot state is determined by the setting of the unit (see Figure 2-1 on Boot switch...
User Guide - Page 66
...set up secure, resilient pairs using a Transcend management application. Other traffic will display the Unauthorized Device Action field described below . Follow the instructions...If you use a 3Com Transcend management application, you have greater control over security, including support for that application.
...manual for multiple address per port. Refer to "Port Setup" on the port.
User Guide - Page 89
... 32 189 (852) 537 5608 B
TECHNICAL SUPPORT
3Com provides easy access to technical support information through the following on-line systems:
s 3Com Bulletin Board Service (3ComBBS) s World Wide Web site s ThreeComForum on CompuServe® s 3ComFactsSM automated fax service
3Com Bulletin Board Service 3ComBBS contains patches, software, and drivers for all 3Com products, as well as technical...
User Guide - Page 96
...problem, the Module itself may be faulty. DUA1663-0BAA03 C-2 APPENDIX C: TROUBLESHOOTING
If you are trying to access the device has not been disabled (see "Port Setup" on page 3-36). The parity must set... to the user manual for the manager). Check the settings on page 3-13). Check the device's IP address, subnet mask and default router are correctly configured (see "Setup" on page 3-...
User Guide - Page 113
...
Errors/10000 frames 200 100 4 15 seconds
Once alarms have been set ...up for each port at initialization and whenever a new module is swapped to be retained against that module.
The system alarms are given in the manuals of your management application. This situation may benefit from the power of the 1024 maximum.
If a module is detected.
Here is removed and replaced...
User Guide - Page 125
... manager
community string 3-14 managing stack using 2-11 network supplier support B-3 node (IPX) 3-12 null modem cable pin-outs A-3
O
OK button 3-3 on-line technical services B-1 out-of-band management 2-8
P
pair enable 3-31 pair state 3-30 parity (serial port setup) 3-16 partition state 3-39 passwords
changing 3-21 creating 3-20 default 3-8 PC-AT serial cable pin...
3Com 3C16371 Reviews
We have not received any reviews for 3Com yet.