Owner's Manual
Page 209
... of its clip and insert the end into its holding clip. After closing the hood, make sure it to about a foot (30 cm) above the fender, then press down firmly with your hands. After closing the hood, make sure it up. SUPPORT ROD 4-cylinder models 6-cylinder models 3. Lift the hood up... slightly to about a foot (30 cm) above the fender, then let it drop. CONTINUED Before Driving 207 Put the support rod back into the hole on the front of the way and hold it...
... of its clip and insert the end into its holding clip. After closing the hood, make sure it to about a foot (30 cm) above the fender, then press down firmly with your hands. After closing the hood, make sure it up. SUPPORT ROD 4-cylinder models 6-cylinder models 3. Lift the hood up... slightly to about a foot (30 cm) above the fender, then let it drop. CONTINUED Before Driving 207 Put the support rod back into the hole on the front of the way and hold it...
Owner's Manual
Page 318
... the driver's side, turn the steering wheel all the way. 6. Remove the bulb by squeezing the connector to remove the two holding clips from the fender and bumper. 4. Lights Low Beam Headlight BULB HOLDING CLIPS TAB 6-cylinder models 5. If you are changing the bulb on the headlights to test the new... the two fasteners and secure them by pushing on the heads until they lock. 1. Push the electrical connector back onto the bulb. Pull the inner fender cover away from the inner...
... the driver's side, turn the steering wheel all the way. 6. Remove the bulb by squeezing the connector to remove the two holding clips from the fender and bumper. 4. Lights Low Beam Headlight BULB HOLDING CLIPS TAB 6-cylinder models 5. If you are changing the bulb on the headlights to test the new... the two fasteners and secure them by pushing on the heads until they lock. 1. Push the electrical connector back onto the bulb. Pull the inner fender cover away from the inner...
Owner's Manual
Page 319
...CONTINUED Maintenance 315 Lock each one in place. If you are changing the bulb on the center. 1. Make sure it in place. 7. Put the inner fender cover in place by turning it one -quarter turn clockwise to test the new bulb. 9. Insert the new bulb into the hole and turn it... one -quarter turn counterclockwise. Install the two holding clips from the fender and bumper. 4. Remove the socket from the headlight assembly by pushing on the driver's side, turn off the engine. Push the electrical connector back onto...
...CONTINUED Maintenance 315 Lock each one in place. If you are changing the bulb on the center. 1. Make sure it in place. 7. Put the inner fender cover in place by turning it one -quarter turn clockwise to test the new bulb. 9. Insert the new bulb into the hole and turn it... one -quarter turn counterclockwise. Install the two holding clips from the fender and bumper. 4. Remove the socket from the headlight assembly by pushing on the driver's side, turn off the engine. Push the electrical connector back onto...
Owner's Manual
Page 320
Turn it clockwise to lock it in the socket. Test the lights to lock it in place. Lock each one in place by pushing it in and turning the bulb counterclockwise until it clockwise to make sure the new bulb is working. 9. Put the inner fender cover in place. 7. Remove the burned out bulb from the socket by pushing on the center. 316 Maintenance Lights 5. Turn it unlocks. 6. Insert the socket back into the headlight assembly. Install the holding clips. Install the new bulb in place. 8.
Turn it clockwise to lock it in the socket. Test the lights to lock it in place. Lock each one in place by pushing it in and turning the bulb counterclockwise until it clockwise to make sure the new bulb is working. 9. Put the inner fender cover in place. 7. Remove the burned out bulb from the socket by pushing on the center. 316 Maintenance Lights 5. Turn it unlocks. 6. Insert the socket back into the headlight assembly. Install the holding clips. Install the new bulb in place. 8.
Owner's Manual
Page 321
Lights Replacing Rear Bulbs (in Fenders) BULBS 2. Pull the bulb straight out of the two bulbs is working. Reinstall the socket into the light assembly by turning it clockwise until it ...
Lights Replacing Rear Bulbs (in Fenders) BULBS 2. Pull the bulb straight out of the two bulbs is working. Reinstall the socket into the light assembly by turning it clockwise until it ...
Owner's Manual
Page 339
Loosen the five wheel nuts 1/2 turn with the wheel wrench. 336 Taking Care of the Unexpected Changing a Flat Tire WHEEL NUTS JACK 6. Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. 8. Remove the cover by turning the handle counterclockwise, then pulling on the cover. 7. The jack is behind a cover in the right fender.
Loosen the five wheel nuts 1/2 turn with the wheel wrench. 336 Taking Care of the Unexpected Changing a Flat Tire WHEEL NUTS JACK 6. Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. 8. Remove the cover by turning the handle counterclockwise, then pulling on the cover. 7. The jack is behind a cover in the right fender.