Whirlpool WTW5500XW Support Question
Whirlpool WTW5500XW Support Question
Find answers below for this question about Whirlpool WTW5500XW.Need a Whirlpool WTW5500XW manual? We have 5 online manuals for this item!
Question posted by Mdmar on December 24th, 2013
Whirlpool Cabrio Washer Wtw5500xw Wont Start
The person who posted this question about this Whirlpool product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Whirlpool WTW5500XW Manual Pages
Dimension Guide - Page 1
... of drain hose should be at least 39" (990 mm) above floor;
This washer has been tested for floor standpipe drain system.
Dimensions are minimum required. Specifications subject ...parts. Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Top of laundry tub must ...
Installation Instructions - Page 2
...REQUIREMENTS
Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686... diameter to improve performance and minimize noise and possible "washer walk". INSTALLATION REQUIREMENTS
Tools and Parts Gather required tools and parts before starting installation.
Install your Use and Care Guide. n 8212656RP ...
Installation Instructions - Page 3
... kgs).
If a closet door or louvered door is not recommended. Top of installation and servicing, and spacing for companion appliances and clearances for ease of laundry tub must support washer's total weight (with beaded tie strap.
3 Installing on the sides.
Floor standpipe drain system
IMPORTANT: Do not install, store, or operate...
Installation Instructions - Page 4
...start: remove shipping materials It is necessary to remove all shipping materials for proper operation.
n Do not have the properly grounded outlet installed by a qualified electrician. Tip washer back and place on floor behind washer. Set washer..., it must be in the neutral or ground circuit.
48" (1.2 m)
Move washer to a gas pipe. n If codes permit and a separate ground wire is used...
Installation Instructions - Page 5
... drain hose should be used.
5 Squeeze clamp with pliers and slide black elbow end of laundry tub. For a laundry tub or standpipe drain, go to remove all parts from rear panel. See "Tools and... Be sure to step 6.
IMPORTANT: 4.5" (113 mm) of laundry tub. You may need to free from tray.
Attach drain hose to back of washer.
4.5" (113 mm)
Place hose into standpipe or lay on ...
Installation Instructions - Page 6
...to check for a few seconds through hoses into a laundry tub, drainpipe, or bucket to water faucets with new inlet hoses with flat washers (not provided). Damage can result. In most standard configurations...: To reduce risk of which hose is snug. A small amount of water may need to washer correctly. IMPORTANT: Do not overtighten or use old hoses. Use pliers to hot water inlet valve...
Installation Instructions - Page 7
... level, use a 9/16" or 14 mm open -end or adjustable wrench to turn the leveling foot clockwise to lower the washer or counterclockwise to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with floor. Not Level
LEVEL
Not Level
7 Adjust leveling feet
Jam nut
Secure drain hose ...
Installation Instructions - Page 8
... correct electrical supply and recommended grounding method.
Close lid. Start washer and allow to see what was skipped. q Check that you have all of /recycle all parts are on washer. q Dispose of your tools. q Read "Washer Use" in your washer, measure 1/2 of normal
recommended amount of washer.
q Remove protective film from back of powdered or liquid...
Owners Manual - Page 3
... of the cycle, as the lid lock goes through a self-test.
And sometimes, you start the cycle, the lid will lock, and the washer will be different kinds of your load or allows time for your previous washer. This low-water wash method uses less water and energy compared to use. HE detergents...
Owners Manual - Page 4
.... This is working properly. You may be changed. Lighter soil level setting will start over when the washer is added at different stages in short pulses to the load.
You will hear the... heavily soiled and sturdy fabrics, press Soil Level to select more damp.
Rather than what your laundry load. At each wash cycle.
SOIL LEVEL Soil level (wash time) is preset for your ...
Owners Manual - Page 5
... they will not spin.
When this cycle is complete, this cycle to open the lid, press START/PAUSE/ UNLOCK. This cycle uses a higher, preset water level.
Use this cycle to wash lightly...small items in a hurry. DONE
Once the cycle is used, the wash cycle will unlock once the washer movement has stopped.
Use once a month to the Normal cycle. Quick Wash
Normal
Eco Normal
No-...
Owners Manual - Page 6
... items, load evenly. Separate lint-takers from towels, rugs, and chenille fabrics. Try mixing different sized items to your laundry
2. NOTE: Always read and follow fabric care label instructions to avoid damage to reduce tangling.
Do not wrap large items...
• Do not dry garments if stains remain after washing, because heat can set stains into washer
• Empty pockets.
Owners Manual - Page 7
...distribution at the end of water to the bottom of cleaning washer dispenser trays. Starting Your Washer
6. Do not use more
information, see "Control Panel"....
7 Low-water washing creates excessive sudsing with liquid chlorine bleach. Using Oxi or color-safe bleach: If using an Oxi or color-safe bleach laundry...
Owners Manual - Page 8
...9. Filling is delayed for more than 10 minutes, water will be cooler than what your previous washer provided. Promptly remove garments after cycle has completed to avoid odor, reduce wrinkling, and rusting of... Moderate to restart the cycle.
the lid will light. Then close the lid and press START/PAUSE/UNLOCK again to light soils
Cool - Delay in soil removal and to open for several...
Owners Manual - Page 9
... your clothes. Close washer lid.
4. Press START/PAUSE/UNLOCK. Turn off both water faucets; To winterize washer: 1. Shut off water supply to washer, to avoid flooding due
to washer. 2. Periodically inspect ...in your washer. Pull tray out until you are not dishwasher safe.
Because some water may find laundry product residue in hoses, freezing can damage washer.
If ...
Owners Manual - Page 11
...our website at www.whirlpool.com/help
Clicking or metallic noises
Objects caught in washer drain system.
Water Leaks
Check the following for assistance and to washer.
Water may be ...hose flat washers are removed during the spin/drain cycles. Wash smaller loads to drainpipe or laundry tub.
Loose items such as final amounts of water for leaks (laundry tubs, ...
Owners Manual - Page 12
...try the solutions suggested here or visit our website at www.whirlpool.com/help for washer to run or fill, washer stops working or wash light remains on (indicating that may hear... water supply.
Washer will pause during certain phases of the spins. Do not add more than 1 or 2 additional items after cycle has started. Select RINSE & SPIN. Press START/PAUSE/UNLOCK.
Do...
Owners Manual - Page 13
...proper water supply. The washer may be on load after washer has started.
13 To remove extra water in the basket. Tightly packed or unbalanced loads may have both washer and faucet, and ...light remains on (indicating that inlet valve screens are not clogged.
The washer is less efficient at www.whirlpool.com/help for assistance and to inlet valve. TROUBLESHOOTING
First try the ...
Owners Manual - Page 14
...Washer" section.
Added water lifts the laundry off the washplate, resulting in water.
on load size and soil level. Added more water to measure correctly.
Washer is less efficient at www.whirlpool...
Always measure detergent and follow manufacturer's directions based on load after washer has started.
Use Whites and Heavy Duty cycle for fabric type. Avoid overfilling.
Load...
Owners Manual - Page 15
... or laundry products dispensing too soon.
Close the lid.
If you experience
Possible Causes
Washer not performing as recommended.
The washer may have tangled. Tie all strings and straps before starting a .... TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/help for assistance and to avoid snags and tears. Garment care instructions ...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
The water temperature is not correct - Cabrio® washer with Dispensers in Corners
...start-up the available hot water faster than your previous washer...Cabrio washer is not correct - video Display shows HC - washer with Dispensers in Corners The water temperature in a short amount of time may use up operation. Top-load HE washer...washer? The water temperature is not correct. Check to the washer..., the washer will display...distance from the washer? You may ... -
Display shows LF - Top-load washer with Dispensers in Corners
... - Click the following to learn more about proper drain systems for Cabrio washers. The example shown is for service. How the washer drains Is the drain hose taped onto the drainpipe? The drain hose... drainpipe or laundry tub. If the water pressure is at least 39" (99 cm) high (as measured from the screens. Drained water can create suction, (siphon) and the water will start to flow... -
Washer is not cleaning laundry - Top-load HE washer with Dispensers in Corners
... Dispensers in your water. Items should move easily for details. Sort loads before starting the washer. Use hot or warm washes, if the warmer temperatures are safe for details.... that the wash load is not cleaning laundry - Use your product model number in my washer? Check the garment fabric care labels for the Cabrio washer. Measure fabric softener to the cold...
