Whirlpool WTW5500XW Support Question
Whirlpool WTW5500XW Support Question
Find answers below for this question about Whirlpool WTW5500XW.Need a Whirlpool WTW5500XW manual? We have 5 online manuals for this item!
Question posted by MzMirafa on August 8th, 2014
Cabrio Washer Wtw5500xw Wont Start
The person who posted this question about this Whirlpool product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Whirlpool WTW5500XW Manual Pages
Dimension Guide - Page 1
....
For complete details, see Installation Instructions packed with spacing of 0" (0 mm) clearance on all sides of 1" (25 mm) on the sides. It is required. This washer has been tested for planning purposes only. Top of laundry tub must be inside standpipe or below the top of the door are required.
Top-Loading...
Installation Instructions - Page 2
...installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686 mm)
42" (1067 mm)
2 Install your washer to 19⁄16" (39.5 mm).... INSTALLATION REQUIREMENTS
Tools and Parts Gather required tools and parts before starting installation. Tools needed:
Parts needed: (Not supplied with washer)
Adjustable or open end wrench 9/16" (14 mm)
4" ...
Installation Instructions - Page 3
... 96" (2.44 m) from bottom of washer. Top of washer. Secure drain hose with maximum slope of washer to weather or in door are minimum required. Water remaining in washer after use may be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Top of wash tub. This washer has been tested for installation with...
Installation Instructions - Page 4
...with a qualified electrician if you start: remove shipping materials It is necessary to have a fuse in the neutral or ground circuit.
48" (1.2 m)
Move washer to within 4 ft (1.2 m)...separate circuit breaker serving only this time.
4 n Check with local codes and ordinances. Set washer upright. n Do not have the properly grounded outlet installed by a qualified electrician. IMPORTANT: ...
Installation Instructions - Page 5
...form as shown. Drain hose form must be inside standpipe; For a laundry tub or standpipe drain, go to drain port
Remove tape from washer lid, open lid and remove cardboard packing tray from tub
Connect Drain ...Hose
5. IMPORTANT: 4.5" (113 mm) of laundry tub. Be sure to back of washer.
4.5" (113 mm)
Place hose into standpipe or lay on elbow end of ...
Installation Instructions - Page 6
...Check for leaks
Turn on valve when attaching to prevent clogs. Connect inlet hoses to washer
Attach hose to water faucets
Run water for cold water faucet. IMPORTANT: Do not overtighten...additional parts with second hose for a few seconds through hoses into a laundry tub, drainpipe, or bucket to faucets or washer. Clear water lines
For floor drain installations, you must be connected ...
Installation Instructions - Page 7
..., use a 9/16" or 14 mm open -end or adjustable wrench to check levelness of washer. Use side seam as shown. Rock washer back and forth to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with floor. If washer is level, use a 9/16" or 14 mm open -end or adjustable wrench to...
Installation Instructions - Page 8
... are on some models). q Remove protective film from back of your tools.
Start washer and allow to see what was skipped.
q Check that washer is an extra part, go back through steps to complete full cycle.
8 q To test and clean your Washer User Instructions. q Check that yellow shipping materials were completely
removed from console...
Owners Manual - Page 3
... of the wash cycle, you may hear nothing at the beginning of water as with dirty laundry, fill it evenly around the basket wall. For example, you may hear sounds and noises ...performance.
Rather than diluting detergent as the washer determines the correct water level for the load. And sometimes, you start the cycle, the lid will lock, and the washer will settle in the "Cycle Status ...
Owners Manual - Page 4
...is restarted. The washer will help reduce...washer provided.
• Even in an agitator-style washer, this washer...but will start over when the washer is added ...based on , the washer is on the type...SPIN SPEED This washer automatically selects the ...washer rinses and moves the load.
Unlike traditional washers... added to the washer to maintain a minimum...washer. This is not... washers....
Owners Manual - Page 5
...lid will not spin.
CYCLE GUIDE
Settings and options shown in washer
Clean Washer
with enough water to open the lid, press START/PAUSE/ UNLOCK.
Use this cycle to wash lightly soiled garments...Extra Rinse
Cycle Details:
Use this light will come on. Use this cycle to drain washer after cancelling a cycle or completing a cycle after power interruption.
This cycle features a ...
Owners Manual - Page 6
Loose change, buttons, or any small object can set stains into washer
• Empty pockets. Helpful Tips:
• When washing water-...Try mixing different sized items to items during washing. USING YOUR WASHER
1. NOTE: Always read and follow fabric care label instructions to avoid damage to your laundry
2.
Load laundry into fabric.
• Treat stains promptly.
• Close ...
Owners Manual - Page 7
...dispense into the last rinse. Pour a measured amount of fabric softener based on the washer.
7. Starting Your Washer
6. This tray holds 3 oz. (89 mL). Using regular detergent will cause fabric... knob to dispenser
Fabric softener tray
Add a measured amount of the washer basket before adding clothes.
Using Laundry Product Dispensers
3. Add fabric softener to choose your load size. If...
Owners Manual - Page 8
... to assist in soil removal and to save energy. Some cycles will unlock once the washer movement has stopped. Select cycle settings
10. Press START/Pause/Unlock
to check for that bleed or fade Light soils
Press the START/PAUSE/UNLOCK button to restart the cycle. brights/darks Warm water is delayed for...
Owners Manual - Page 9
... recommended monthly cleaning procedure:
1. Do not use to reduce the risk of hose failure. Press START/PAUSE/UNLOCK. To clean exterior:
1. IMPORTANT: To avoid damaging the washer's finish, do not interrupt cycle. Because some water may find laundry product residue in basket and run a RINSE AND SPIN cycle to ensure cleaner or bleach...
Owners Manual - Page 11
.... Water Leaks
Check the following for proper installation:
Washer not level.
Check all four fill hose flat washers are removed during the spin/drain cycles. Washer may block pump.
If you have started the washer.
The washer senses load sizes and adds correct amount of water for leaks (laundry tubs, drain pipe, water pipes, and faucets.)
Unbalanced...
Owners Manual - Page 12
... Hot and Cold water faucets must be tightly packed.
Ensure there is power to the washer.
Close lid and press START/PAUSE/UNLOCK. Do not add more detergent.
12
Check that the washer was unable to inlet valve.
Replace any kinks in basket. NOTE: If problems continue, contact an electrician. Do not add...
Owners Manual - Page 13
...DRAIN & SPIN. Load garments in pump or between basket and tub, which can keep washer from regular detergent can slow draining.
Check plumbing for proper installation. Check drain hose for...correct drain
hose installation. Always measure and follow detergent directions based on load after washer has started.
13
Make sure hot and cold inlet hoses are not reversed.
Be sure to...
Owners Manual - Page 14
... water.
Do not add products directly onto load. See the "Cycle Guide" to move. Added water lifts the laundry off the washplate, resulting in water.
Not washing like colors together and remove promptly after washer has started. Add an Extra Rinse to possibly avoid a service call. The suds from regular detergent can keep...
Owners Manual - Page 15
... and follow the manufacturer's directions. Monthly maintenance not done as expected (cont.)
Incorrect dispenser operation
Clogged dispensers or laundry products dispensing too soon. Unload washer as soon as cycle is started.
The washer will not start or fill with low water pressure may result in residual powder in a tightly packed load. This may have been...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
The water temperature is not correct - Cabrio® washer with Dispensers in Corners
... and cold water inlet hoses were reversed during start-up the available hot water faster than I expect - The distance from the washer? Top-load washer Warm or hot wash temperatures are in a ...in my Cabrio washer is not correct - Do you have an Energy Star® qualified washer? Check that there are reversed, the washer will display an "HC" error code at the end of laundry. You ... -
Display shows LF - Top-load washer with Dispensers in Corners
...source of water. The washer will start to flow out of the drain is below 39" (99 cm), the water will not properly operate with Dispensers in Corners My Cabrio washer display shows LF. Do...must be too far inside the drainpipe (standpipe) or laundry tub. Turn off the water and remove inlet hoses from the screens. How the washer drains Is the drain hose taped onto the drainpipe? ... -
Washer is not cleaning laundry - Top-load HE washer with Dispensers in Corners
... only. Regular detergent creates too many suds for temperature recommendations. Sort loads before starting the washer. Use more rinsing. Use only High Efficiency (HE) detergent. Check your... connected to the hot faucet and the cold-water fill hose is not cleaning laundry - My Cabrio HE washer is automatically added during the rinse portion of the cycle. See also: ...
