Whirlpool WTW5500XW Support Question
Whirlpool WTW5500XW Support Question
Find answers below for this question about Whirlpool WTW5500XW.Need a Whirlpool WTW5500XW manual? We have 5 online manuals for this item!
Question posted by torJdma on August 18th, 2014
Fill Light On Washer Flashing Wont Start
The person who posted this question about this Whirlpool product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Whirlpool WTW5500XW Manual Pages
Dimension Guide - Page 1
... from bottom of washer.
This washer has been tested for walls, doors, and floor moldings.
Top of laundry tub must install higher than 96" (2.44 m) from bottom of washer. Dimensions are for...(126 mm)
17" (432 mm)
48 in.2 (310 cm2)
24 in door are minimum required.
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Louvered doors with spacing of 0" (0 mm) clearance...
Installation Instructions - Page 2
...LOCATION REQUIREMENTS
Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686 mm... tools and parts before starting installation.
Tools needed:
Parts needed: (Not supplied with flat washers
To order, please refer to improve performance and minimize noise and possible "washer walk". n 8212656RP n...
Installation Instructions - Page 3
... on back of
power cord on carpet is installed, top and bottom air openings in washer after use may be needed.)
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Water remaining in door are minimum required. This washer has been tested for a standpipe drain: 2" (51 mm).
Proper installation is your responsibility. Recessed...
Installation Instructions - Page 4
...start: remove shipping materials It is necessary to avoid excessive noise from shipping carton on cardboard supports. Remove shipping base
To avoid damaging floor, place cardboard supports from washer.
1. Set washer upright. If your washer...of its final location; it at this appliance be provided. n This washer is recommended.
n To minimize possible shock hazard, the cord must be...
Installation Instructions - Page 5
... to remove all parts from rear panel. IMPORTANT: 4.5" (113 mm) of drain hose, slide it over side of laundry tub. For a laundry tub or standpipe drain, go to drain port
Remove tape from washer lid, open lid and remove cardboard packing tray from tub
Connect Drain Hose
5. Place drain hose in Step 7. do...
Installation Instructions - Page 6
... until it is snug. Repeat this step with second hose for a few seconds through hoses into a laundry tub, drainpipe, or bucket to a cold water faucet, you must use a Y-adapter (not provided)....bulges, kinks, cuts, wear, or leaks are only connecting to prevent clogs. You may enter washer. Connect inlet hoses to tighten couplings an additional two-thirds turn . Use pliers to water ...
Installation Instructions - Page 7
... counterclockwise on top edges of front using lid, as needed. If washer is level, use a 9/16" or 14 mm open -end or adjustable wrench to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with floor.
Check levelness of washer.
HELPFUL TIP: You may want to step 14.
Secure drain hose...
Installation Instructions - Page 8
...Complete Installation CHECKLIST
q Check electrical requirements. Select any tape
remaining on . Plug into washer basket or detergent dispenser (on some models). q Check that you have all packaging ...
q Check that all parts are on washer. Be sure you have correct electrical supply and recommended grounding method. Close lid. Start washer and allow to see what was skipped....
Owners Manual - Page 3
...washer, this washer delivers the detergent directly to produce the right amount of the wash cycle, you start the cycle, the lid will lock, and the washer...washer is needed. The washer automatically adjusts the water level to a traditional agitator-style washer. You will likely result in the "Cycle Status Lights...excessive sudsing with dirty laundry, fill it evenly around the basket wall....
Owners Manual - Page 4
...rinse to most loads, use the warmest wash water safe for the load. SENSING
When the Start/Pause/Unlock button is normal. You will first perform a self-test on the lid lock ...cycles on your laundry load. SOIL LEVEL Soil level (wash time) is working properly.
For lightly soiled and delicate fabrics, press Soil Level to select more damp. SPIN SPEED This washer automatically selects ...
Owners Manual - Page 5
... items than for loads requiring an additional rinse cycle or to thoroughly clean the washer interior.
5 Use this light will use for normally soiled cottons and mixed fabric loads. Spin speed is high... and select a cycle based on the care label.
Use this cycle to open the lid, press START/PAUSE/ UNLOCK. Use once a month to shorten drying times for that best fits the load being ...
Owners Manual - Page 6
...by recommended cycle, water temperature, and colorfastness.
• Separate heavily soiled items from lightly soiled.
• Separate delicate items from sturdy fabrics.
• Do not dry garments if... because heat can set stains into washer
• Empty pockets.
NOTE: Always read and follow fabric care label instructions to avoid damage to your laundry
2.
Do not wrap large items ...
Owners Manual - Page 7
...into the last rinse. Select cycle
Turn cycle knob to turn on the washer.
7. Using Laundry Product Dispensers
3. Close dispenser drawer, then select Fabric Softener option.
Make ...
information, see "Control Panel".
7 Add fabric softener to immediately dispense into detergent tray.
Starting Your Washer
6. This tray holds 3 oz. (89 mL). Do not overfill or dilute. If...
Owners Manual - Page 8
.... Unlocking the lid to add garments If you need to open for that bleed or fade Light soils
Press the START/PAUSE/UNLOCK button to add, if not previously set. This is added to your previous washer provided. NOTE: Not all options are available with all cycles.
8
brights/darks Warm water is sensed...
Owners Manual - Page 9
...washer. Close washer lid.
4. Press START/PAUSE/UNLOCK. Water will pour into slot. To clean exterior:
1.
Turn off both water faucets; WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer...your dispenser trays. WASHER MAINTENANCE
WATER INLET HOSES
Replace inlet hoses after 5 years of use abrasive products. Because some water may find laundry product residue in ...
Owners Manual - Page 11
... hear metal items on . Washer not performing as expected
Not enough water in washer
Load not completely covered in washer drain system.
Humming
The sensing light is normal to be in ...be unbalanced. Wash smaller loads to drainpipe or laundry tub. Empty pockets before water is added to the washer. Gurgling or humming
Washer may not be draining water.
This is not...
Owners Manual - Page 12
...become clogged.
Normal washer operation.
You may be turned on (indicating that the washer was unable to run or fill, washer stops working or wash light remains on . Washer may take 2...slow or stop the washer. Do not add more than 1 or 2 additional items after cycle has started.
NOTE: If problems continue, contact an electrician. Press START/PAUSE/UNLOCK.
Only use...
Owners Manual - Page 13
...clogs from operating correctly.
Always measure and follow detergent directions based on washer may be on load after washer has started.
13 Check for proper water supply.
Energy saving controlled wash temperatures.... are still wet or spin light remains on (indicating that inlet valve screens are not reversed. Both hoses must be attached to both washer and faucet, and have both...
Owners Manual - Page 14
... started. Do not add products directly onto load.
See the "Cycle Guide" to avoid chlorine bleach and fabric softener staining.
Avoid overfilling. If you experience
Possible Causes
Solution
Washer not performing as recommended. Added water lifts the laundry off the washplate, resulting in water.
Use dispensers to match your load with the best...
Owners Manual - Page 15
...directions. Button sounds can occur in seams before starting wash load. Monthly maintenance not done as cycle is flashing.
The washer will not unlock until the basket has stopped ...Washer" in the dispenser. Unload washer as soon as recommended.
If you experience
Possible Causes
Washer not performing as expected (cont.)
Incorrect dispenser operation
Clogged dispensers or laundry...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Lights flashing on the dishwasher
... that the dishes inside it necessary to use a rinse agent in my dishwasher? You should call for service if the Clean light is flashing and the machine is complete, the light will not start Is it are flashing. The Clean light is locked Dishwasher shuts off . Once the door is opened after the cycle is complete. -
Lights flashing on the dishwasher
Once the door is opened after the cycle is complete. My is locked shuts off . Lights flashing on the dishwasher The lights on after the cycle is complete, the light will not start Is it are flashing. The Clean light is an indication that the has been run and that the dishes inside it necessary to use a rinse... -
Lid lock light is flashing - Top Load HE with Dispenser Drawer
... has stopped spinning.This may still be spinning. The lid will not fill or start or fill with Dispensers in Corners Spin light remains on my washer. Lid lock light is flashing on - Was a cycle stopped or paused using the Start/Pause/Unlock button? Top Load HE with Dispenser Drawer - Find Manuals & Is the...
Similar Questions
Wfw94hexw Timer Light Blinks, Cycle Wont Start
When we load clothes, the door locks, unlocks and the timer number blink and cycle wont start What i...
When we load clothes, the door locks, unlocks and the timer number blink and cycle wont start What i...
(Posted by brmom 12 years ago)