Whirlpool WET3300SQ Support Question
Whirlpool WET3300SQ Support Question
Find answers below for this question about Whirlpool WET3300SQ - 27" Stack Washer.Need a Whirlpool WET3300SQ manual? We have 2 online manuals for this item!
Question posted by irishk4 on November 5th, 2010
Washer Will Not Wash Or Rinse And Drain Water.
My washer will fill up with water and then once the load is full with water, the process stops. It does not wash, rinse, spin or drain water. What can I do to fix this problem? is it a fuse or belt?
Current Answers
Answer #1: Posted by naptha on November 5th, 2010 2:25 PM
naptha
Member since:
August 20th, 2010 Points: 73,090
Member since:
August 20th, 2010 Points: 73,090
I had one do this once and it was the lid switch that was bad. You can check the switch or the little tab on the lid that hits the switch if your model is set up that way. I unhooked the wires from my switch and connected them together and taped them up very good. If you try this be sure to unplug your unit and turn off the water supply first. This will make washer run with the lid up in any cycle so be careful. Sometimes these switches can be very difficult to get to. Some washers have switches that are not visible but they are there. It could also be in the selector. If you can see the switch try pushing it in with something nonconductive after it fills. Sometimes they get worn and the lid tab won't reach any more, or tab could be broken.
Answer #2: Posted by ambato44 on April 10th, 2011 7:48 AM
ambato44
Member since:
April 10th, 2011 Points: 2,070
Member since:
April 10th, 2011 Points: 2,070
main suspect is the timer. Age of machine has not been stated but normally this component of the unit will cause that symptom. qtl { position: absolute; border: 1px solid #cccccc; -moz-border-radius: 5px; opacity: 0.2; line-height: 100%; z-index: 999; direction: ltr; } qtl:hover,qtl.open { opacity: 1; } qtl,qtlbar { height: 22px; } qtlbar { display: block; width: 100%; background-color: #cccccc; cursor: move; } qtlbar img { border: 0; padding: 3px; height: 16px; width: 16px; cursor: pointer; } qtlbar img:hover { background-color: #aaaaff; } qtl>iframe { border: 0; height: 0; width: 0; } qtl.open { height: auto; } qtl.open>iframe { height: 200px; width: 300px; }
Related Whirlpool WET3300SQ Manual Pages
User Instructions - Page 1
®
WASHER/DRYER USER INSTRUCTIONS
INSTRUCCIONES PARA EL USUARIO DE LA LAVADORA/SECADORA
...provide proof of Contents / Índice / Table des matières
ASSISTANCE OR SERVICE 1 WASHER/DRYER SAFETY 2 WASHER USE 4 DRYER USE 5 WASHER/DRYER CARE 6 TROUBLESHOOTING WASHER 8 TROUBLESHOOTING DRYER 10 WARRANTY 12
AYUDA O SERVICIO TÉCNICO 13
SEGURIDAD DE LA LAVADORA/SECADORA...
User Instructions - Page 2
... all occupants. • Immediately call your gas supplier, call the fire department.
- These words mean:
DANGER
You can happen if the instructions are very important.
WASHER/DRYER SAFETY
Your safety and the safety of others .
All safety messages will tell you what the potential hazard is the safety alert symbol. This...
User Instructions - Page 3
...; Before the washer/dryer is removed from each load.
■ Under certain conditions, hydrogen gas may contribute to a chemical reaction that could ignite or explode.
■ Do not add gasoline, dry-cleaning solvents, or other flammable, or explosive substances as they give off vapors that could cause a load to the wash water.
SAVE THESE INSTRUCTIONS...
User Instructions - Page 4
... oils). Mix large and small items. Items should move easily through the wash water.
Use the straightest path possible when routing the vent.
4. Do not guess. Follow manufacturer's directions for a full load. 3. When cleaning is complete, be removed in a new location. LARGE CAPACITY WASHERS
Heavy Work Clothes
2 pair of pants 3 shirts 3 jeans 1 coverall
Mixed...
User Instructions - Page 5
... automatically during the rinse portion of the cycle. Turn the Start button to start the washer. Press the PUSH...stop or restart your washer:
■ To stop the washer at any fabric softener onto the clothes. Your dryer may not have all of fabric being washed. Load... load size or water level selection after washing).
The signal is set to On.
5. The signal will not agitate or spin with...
User Instructions - Page 6
... Hoses
Replace inlet hoses after 5 years of replacement on the label with your washer and run the dryer with hot water and liquid detergent. Do not rinse or wash
screen to dry the drum. As Needed Cleaning
Laundry detergent and fabric softener residue can build up . 2. Dry unstable dye items inside the dryer on some...
User Instructions - Page 7
... 2 years, or more often, depending on a drain and spin setting for about 30 seconds
to secure the washer lid and dryer door. Non-use an adapter.
Put 1 qt (1 L) of detergent to mix the antifreeze and water. 4.
To transport the washer/dryer 1. Disconnect the drain from the drain system. 5. Run the washer through a complete cycle with 1 scoop or
capful...
User Instructions - Page 8
... rinses can contribute to move freely.
Washer Operation
Washer won't run, fill, rinse or agitate;
The drain hose should be able to follow the manufacturer's directions when adding fabric softener to the drainpipe or laundry tub. Replace the fuse, or reset the circuit breaker. Washer and Components
Noisy, vibrating, off the tub ring?
Turn off the load. Turn on water...
User Instructions - Page 9
...? Wash water colder than 96" (244 cm) above average iron (rust) in water? Check to the right faucets. Do not seal the drain hose with a higher spin speed (if available).
■ Did you might need to the rinse portion of basket holes. Washer will cause wrinkling. Follow manufacturer's directions. As your water colder than the control knobs on load...
User Instructions - Page 10
...solutions suggested here and possibly avoid the cost of load.
■ Were strings and sashes tied to Timed or Air Dry? Use a time-delay fuse.
■ Is the dryer door firmly closed... entangled in seams before washing.
■ Did you overload the washer? Do not place load items on the supply line? The drum may not have not tripped. If a problem continues, call an electrician...
User Instructions - Page 1
... / Índice / Table des matières
WASHER/DRYER SAFETY 1
INSTALLATION INSTRUCTIONS 2 Tools and Parts 2 Alternate Parts 2 Location Requirements 3 Drain System 4 Electrical Requirements -
27" (69 CM) ELECTRIC WASHER/DRYER INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACIÓN DE LA LAVADORA/ SECADORA ELÉCTRICA DE 27" (69 CM)
INSTRUCTIONS D'INSTALLATION LAVEUSE/SÉCHEUSE...
User Instructions - Page 2
.... If You Have
You Will Need to Buy
Laundry tub or standpipe taller than 96" (2.4 m)
...drain
Siphon break, Part Number 285320, additional drain hose, Part Number 285702 and connector kit, Part Number 285442
Drain hose too short Drain hose, Part Number 285664 and connector kit, Part Number 285442
Lint clogged drain
Drain protector, Part Number 367031
Water faucets beyond reach of the Washer...
User Instructions - Page 3
...Washer/Dryer Care" in low temperatures. This washer/dryer has been tested for mobile home installations. Additional Installation Requirements
This washer/dryer is suitable for spacing of the washer/dryer in .2 (155 cm2)
1" 27..., mobile homes or sleeping quarters. The washer/dryer must conform to support the washer/dryer weight (washer/ dryer, water and load) of 5-100 psi (34.5-689.6 kPa...
User Instructions - Page 4
... 30-amp circuit, fused on both sides of the line. Standpipe drain system - The top...drain system (floor or wall), the laundry tub drain system, or the floor drain system.
The opening (such as the dryer exhaust opening. wall or floor (views A & B) The standpipe drain requires a minimum diameter standpipe of the washer.
39" (99 cm)
A
B
Laundry tub drain system (view C) The laundry...
User Instructions - Page 5
...washer/dryer is recommended. The plug must be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.
■ To supply the required 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply on a separate 30-amp circuit, fused...INSTRUCTIONS
■ For a grounded, cord-connected washer/dryer: This washer/dryer must be grounded. The cord is ...
User Instructions - Page 12
...the straight end of the silver, double-wire clamp with tap
water. Twist hose back and forth while pushing onto drain connector on the cabinet.
2. Release clamp. Screw the feet ...drain hose with pliers to the following instructions: IMPORTANT: To ensure proper installation, this procedure must be at the front corner of the washer/dryer. 2. Housecleaning problems and health problems...
User Instructions - Page 13
... amount
of the inlet hoses. Screw on coupling by hand until it is seated on the washer. 6. Insert a new flat washer into laundry tub or standpipe. A. To keep drain water from under "Tools and Parts."
Put hooked end of drain hose into each end of water might clog the inlet valve screens.
■ Check the temperature of...
User Instructions - Page 14
.... To cover the hole in many varieties. Tightly wrap the shipping strap around the water inlet hoses and the drain hose (C above ).
Rigid metal or flexible metal vent C. Clamps D. Loop system with one offset and one of the Washer/Dryer User Instructions. ■ Over-the-Top Installation:
Part Number 4396028
■ Periscope Installation...
User Instructions - Page 15
...Special provisions for mobile home installations
The exhaust vent must be necessary to level the washer/dryer again after it is secured to exhaust hood with 4" (10.2 cm) clamp... ft (11.3 m) 35 ft (10.7 m)
Flexible metal 25 ft (7.6 m) 20 ft (6.1 m)
1
Rigid metal
32 ft (9.7 m) 27 ft (8.2 m)
Flexible metal 21 ft (6.4 m) 16 ft (4.9 m)
2
Rigid metal
24 ft (7.3 m) 19 ft (5.8 m)
Flexible metal ...
User Instructions - Page 16
...an extra part, go away.
16 Keep the plastic foam for use if the washer/dryer should be 2 household fuses or circuit breakers for heat. For direct wire installation, turn off the dryer and... check the following :
■ Controls are intact and tight, or that the water faucets are tight...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
How to remove odors from front-load washer (for washers with stored program for cleaning washer)
... door will unlock, lock again, and then the cycle will be necessary if this cleaning process. Select the Rinse/Spin setting. The water in your washer. Remove any clothing or items from a front-load washer with several rinse and drain steps to this cleaning process. Add liquid chlorine bleach to Step 6. Use of more than one or two... -
My load-sensing Energy Star top-load washer with agitator is using too much water.
... cycle, sends a signal to drain - Did you lift the lid after fill or during the wash cycle? Washer continues to fill or continues to the control that you stop . When restarted, the washer fills to properly rinse the load using too much water. My load-sensing Energy Star top-load washer with agitator is using the spray... -
How do I remove odors from my Top-loading HE washer?
... once. If the Clean Washer cycle is cancelled, run a Rinse or Rinse & Spin cycle to ensure that all remaining washer cleaner or bleach is recommended that you are using liquid chlorine bleach: Add 1 cup (250 mL) liquid chlorine bleach to use a dehumidifier. If your drain hose installation, usage and water conditions for better ventilation...
Similar Questions
Washer Ywet3300sq1 Stops Mid Cycle And Wont Fill Water To Rinse?
How do I repair it?
How do I repair it?
(Posted by Kfomai 8 years ago)
Washer Is Filling With Hot Instead Of Cold Water And Rinsing In Hot.
Unit is 3 years old
Unit is 3 years old
(Posted by daneyrich 11 years ago)
Age Of This Stack Washer Is???
(Posted by PHILJBRO 11 years ago)
Whirlpool Washer Wet3300sq1 Has A Leak Unde R Machince During Empting Wash Tub A
(Posted by japoksr 12 years ago)
Won't Drain
What would cause the washer to not drain during the spin cycle?
What would cause the washer to not drain during the spin cycle?
(Posted by asuppo 12 years ago)