Question posted by tangooch on December 15th, 2014
Whirlpool Quite Partner I... F6 Error
I have a Quite Partner I (DU1030XTXS1) dishwasher. The diagnostic test indicates an F6 error, after some research I found that F6 is in an intake error. I thought this odd because the dishwasher fills on the prewash cycle, and then hits an error around the time the detergent door opens. The machine then cancels and drains out the water. So I replaced the water inlet valve, and in case there was a blockage in the water line, I have replaced the inlet hose and the shut off valve on the water line under the sink. These replacements have not solved my problem. Is there a water flow sensor (not included on the water inlet valve) on a Quite Partner I (DU1030XTXS1) that I might need to replace? Or could this be an electrical/computer error? Thanks!
Current Answers
Answer #1: Posted by TechSupport101 on December 16th, 2014 3:15 AM
Hi. This is model is said to have been launched with a very sensitive control board- read more here
http://www.applianceblog.com/mainforums/threads/23324-Quiet-Partner-I-randomly-cancels-and-drains
http://www.applianceblog.com/mainforums/threads/23324-Quiet-Partner-I-randomly-cancels-and-drains
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Washer will not fill or start - Cabrio® washer with agitator
... continue. Are the water inlet valve screens on the Cycle control knob properly lined up with agitator. Cabrio® Do not add detergent. Use cold water. Guides: /shared.whirlpoolcorp.com/service/modelnumber.jsp','modelnumber',500,480);return false;" href="#"> Lookup Model # Answers others found helpful Washer will not fill or start - Is the indicator on the washer clogged... -
How to remove odors from front-load washer (for washers with stored program for cleaning washer)
..." (Remove Load) in the Estimated Time Remaining display, an error tone will sound. Always do I clean my front-load washer door seal? Use warm or hot water in the detergent dispenser. Clean the door seal of buttons will fill and run a maintenance cycle. This will be pressed. Replace the detergent compartment divider. When the cycle is rinsed from a front-load washer... -
Removing odors from a front-load washer with the Clean Washer cycle (on control panel)
... Care Guide for washers with Clean Washer cycle Affresh washer cleaner method (recommended) NOTE: Completely read these instructions before using the correct amount of washer interior. For additional information on my Duet® If an error code, ("rL" or "F-34") is complete, leave the door open after a few minutes, see , If odor...
Similar Questions
Dishwasher Fills And Drains But Does Not Wash
my whirlpool dishwasher fills and appears to go through the cycle, and drains but does not actually ...
my whirlpool dishwasher fills and appears to go through the cycle, and drains but does not actually ...
(Posted by mdillow13 6 years ago)
The Braided Water Inlet Hose Doesn't Fit The Water Valve Of My Condo.
The braided water inlet hose doesn't fit the water valve of my condo. I was told to buy an adapter w...
The braided water inlet hose doesn't fit the water valve of my condo. I was told to buy an adapter w...
(Posted by NATALIEJOHNSON 7 years ago)
Machine Full If Water
machine full of water didnt spin..is their a reset botton
machine full of water didnt spin..is their a reset botton
(Posted by dejesusmerle 8 years ago)
Whirlpool Quiet Partner 1 Dishwasher, Leaves A Brown, Smearable Film
My Whirlpool Quiet Partner 1 dishwasher is less than a year old. Almost immediately it began to leav...
My Whirlpool Quiet Partner 1 dishwasher is less than a year old. Almost immediately it began to leav...
(Posted by patbruner57 8 years ago)
Washer Will Not Wash Or Rinse And Drain Water.
My washer will fill up with water and then once the load is full with water, the process stops. It d...
My washer will fill up with water and then once the load is full with water, the process stops. It d...
(Posted by irishk4 13 years ago)