Home » ViewSonic » Computer Monitors » ViewSonic VE910B

ViewSonic VE910B Support Question

Find answers below for this question about ViewSonic VE910B.
Need a ViewSonic VE910B manual? We have 2 online manuals for this item!

ViewSonic Overview Questions Manuals Reviews Videos Research

Question posted by iilka6405 on November 26th, 2022

How To Turn Off Burn In

bought a monitor, accidentally turned it on burn in, I don't know how to turn off this function now, there is nothing about it in the official instructions. help me please

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by rajhbd84 on November 27th, 2022 6:42 AM

This answer was accepted by the poster of the original question.

rajhbd84

Member since:
June 4th, 2022

Points: 3,610

1,100
points

The power button on the monitor wouldn't respond when I tried to follow the steps below to turn it off, so I pulled the power plug and tried again, but nothing happened. Please assist!

* Turn off the monitor while maintaining pressure on the plus and menu buttons

* Press the power button while keeping the other two in place. Release all the buttons after the DVI connector graphic has vanished, then press the minus button. The service menu should appear. Using the minus button, scroll down to Burnin Mode. Pressing the Menu button will activate that setting. Pressing the minus button will change it to off (it should be blue when selected).

* Select Menu from the menu. I recently connected the computer again after it had been unplugged for more than six months (we split up and had to move out). The computer appears to boot up successfully, but my screen is blank. Recently, a blue box with the text "BURN IN MODE" appeared. I am unable to get rid of it and I am unable to use my computer.

Rajkumar Raikwar

Related ViewSonic VE910B Manual Pages

Service Manual - Page 5

... supplied with power that complies with the requirements of Limited Power Source (IEC60950 or UL1950), or an exemption should be taken into an enclosure (LCD monitor housing, for . (14) The LCD module is supplied by a Limited Current Circuit (IEC60950 or UL1950).

Service Manual - Page 6

... of the LCD panel is pressed by fingers and that may cause"Mura" ViewSonic Corporation Confidential - Do Not Copy VE910/b 3 Incorrect Methods: Surface of the monitor. 5.1. That may cause"Mura" Take out the monitor with cushions Taking out the monitor by grasping the LCD panel. Do not touch the surface of the polarizer.

Service Manual - Page 7

Do Not Copy VE910/b 4 Placing the monitor on a clean and soft foam pad. Place the monitor on foreign objects. That may cause "Mura" ViewSonic Corporation Confidential - That could scratch the surface of the panel or cause "Mura" The panel is placed facedown on the lap.

Service Manual - Page 9

...(typ.) 12 ms (Tr= 8.4 ms, Tf =3.6 ms) (maximum) 6. Mechanical Dimensions Width Height Depth Monitor Weight 414 mm 407 mm 219 mm 5.4kg / 11.88 lbs Ergonomics Tilt Up Tilt Down 20 DEGREES ...to do "Auto Adjust" the first time a new mode is no "Auto Adjust" feature. 3) The monitor needs to +12,000 meters ViewSonic Corporation Confidential - Do Not Copy 6 VE910/b Condition: CT = 6500K...

Service Manual - Page 16

...output end of frame short-line. 1,2 Patent Pending PIN DESCRIPTION CPU Interface Pin Name Pin Type Function Pin HWRESET Schmitt Trigger Input w/ 5V-tolerant Hardware reset; The HSYNC input receives a logic signal...direct bus WRZ; It is the 110-220AC input voltage to 12V AND 5V output for LCD monitors with a high-speed integrated triple-ADC/PLL, a high quality display processing engine, and an ...

Service Manual - Page 20

...*480 (H=43.27kHz, V=85Hz) 800*600 (H=53.7kHz, V=85Hz) 1024*768 (H=68.67kHz, V=85Hz) 1280*1024 (H=79.97kHz, V=75Hz) 1.4. Test Condition Before function test and alignment, each LCD Monitor should be run-in and warmed up for at least 30 minutes with SXGA resolution and a sound card) 1.3. Test Display Modes & Pattern 1.4.1 Compatible...

Service Manual - Page 23

..., Press "▲" and " 2 " and turn on power at the same time after power LED is on, release "▲" and " 2 " key, Then press " 1 " key go to 1280x1024 80K/75Hz BURN IN and warm up over 30 minutes. If not, readjust by the following steps: (a) Select and enter "Fine Tune" function on OSD Main Menu...

Service Manual - Page 24

... 9300K Press " 2 " key. Do Not Copy VE910/b 21 Adjust Color Temperature: (1) EEPROM INIT (5 BLOCKS): Press "▼" key move cursor to EEPROM INIT, Press " 2 " key then monitor will INIT ADC value. (2) Press "▲" key move cursor to "White Balance", Press " 2 " key do white balance adjustment. (3) Press "▼" key move cursor to "Color...

Service Manual - Page 25

..., RGB, Black, & Grey Test Tool: 8% ND Filter - The total numbers and distance of dead pixels should do "All Mode Reset" again. 1.5.15 Power Off Monitor Turn off the monitor by pressing "Power" button. Check if the Mura can pass 8% ND Filter. 1.5.13 Check for Secondary Display Modes Test Signal: Analog: 640*350@70Hz...

Service Manual - Page 26

... Firmware Upgrade - Equipment Needed - LPT Cable - Firmware Upgrade Program - PC (Personal Computer) - Do Not Copy VE910/b 23 Firmware Upgrade Procedure When you receive the returned monitor, please check whether the firmware version is the latest. If not, please do the following procedures to upgrade it to the latest version. 2.1. VGA Cable - 2.

Service Manual - Page 27

... Procedure 2.2.1 Connect P2 of Fixture with printer port of PC by LPT Cable. 2.2.2 Connect P1 of Fixture with Q190mb Monitor by VGA Cable. 2.2.4 Connect Power Cord to Q190mb Monitor. 2.2.5 Connect PC to the additional monitor. 2.3. ISP Download program procedure 2.3.1 Hardware Connect status: 2.3.2 Down load isp program Step 1: Execute ISP.exe ViewSonic Corporation Confidential...

Service Manual - Page 30

...find the status like the follow picture. To connect the D-Sub connector and then turn on the power of monitor (AC plug off ) and disconnect the D-Sub connector . If not (failed), ...between PC and ISP board. ViewSonic Corporation Confidential - The connecting status between ISP status and Monitor. b. Step 6: Download program finish Pressing the OK Button to do the firmware upgrade....

User Guide - Page 4

... standards for the time being, permitted in the back light system of flat panel monitors as substances which accumulate in living organisms. **Lead, Cadmium and Mercury are heavy ...rechargeable batteries and in batteries, relays and switches. Mercury is, for disposal. ViewSonic VE910/VE910b ii The complete ecological criteria document can consist of flame retardant substances. Up to delay the...

User Guide - Page 5

... to radio communications. ViewSonic VE910/VE910b 1 This equipment has been tested and found to comply with the limits for help. Also, any unauthorized changes or modifications not expressly approved by turning the equipment off and on a circuit different from that interference will not occur in accordance with the instructions, may cause harmful interference to...

User Guide - Page 9

...LCD display and computer Turn ON the LCD display, then turn ON the computer. NOTE: Windows users may mail or fax to ViewSonic. Follow the on -screen instructions. 5. For instructions on changing the resolution... into the adapter. AC IN AC Outlet (Wall Socket) Computer Power Cord ViewSonic VE910/VE910b D-SUB 5 The ViewSonic Wizard CD-ROM also provides an opportunity for any future customer ...

User Guide - Page 10

Refer to the instructions that the Power button is turned Off, then disconnect the power cord. 2. Attach the LCD display to a wall-mounted display, do the following the instructions in the wallmounting kit. ViewSonic VE910/VE910b 6 To convert your local dealer. Lay the LCD display face down flat against the base as shown. Four screw...

User Guide - Page 11

... down arrow T again for instructions. With or without this setting, after a power failure, your LCD display's power will display for 10 seconds. ViewSonic VE910/VE910b 7 For the best picture ... Timing Mode: 1. If the power button is pressed the message Power Button Locked will automatically turn ON when power is important for maximizing the quality of the resolution (example 1280 x 1024...

User Guide - Page 16

... the menu shown below: Language Select allows the user to turn the OSD background On or Off. For example, with a "15 second" setting, if a control is operating in a factory Preset Timing Mode listed in the menus and control screens. ViewSonic VE910/VE910b 12 OSD Timeout sets the length of this manual. OSD...

User Guide - Page 20

..., non-alcohol based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen. ViewSonic VE910/VE910b 16 If the screen still not clean, apply a small amount of a non-ammonia, non-alcohol based, mild non... screen or case. Cleaning the LCD Display • MAKE SURE THE LCD DISPLAY IS TURNED OFF. • NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE. Use a soft...

User Guide - Page 21

... nature, unauthorized product modification, or failure to follow instructions supplied with a like product. Who the warranty protects.... Causes external to the product, such as "image burn-in material and workmanship during the warranty period, ViewSonic ... Limitation of 1 Release Date: 03-31-05 ViewSonic VE910/VE910b 17 Warranty_VSLCD 4.3: ViewSonic LCD Warranty Rev. 1c 1 of ...