Uniden BC244CLT Support Question
Uniden BC244CLT Support Question
Find answers below for this question about Uniden BC244CLT.Need a Uniden BC244CLT manual? We have 1 online manual for this item!
Question posted by wvcrazy1990 on April 8th, 2016
Uniden Bc244clt Factory Reset
The squelch stays on and gets stuck wwon't scan.I have moved to different. Area in house and still won't scan anything to do a way to factory reset it maybe
Current Answers
Answer #1: Posted by TechSupport101 on April 8th, 2016 8:07 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Hi. See the manual here https://www.helpowl.com/manuals/Uniden/BC244CLT/95085 for assistance with the reset.
Related Uniden BC244CLT Manual Pages
English Owners Manual - Page 2
... operation of this scanning radio in a motor vehicle may be able to provide you read anything else, please observe the following:
Uniden DOES NOT represent this unit to rain or moisture. Your local law enforcement officials should be prohibited, regulated, or require a permit in any way other than as detailed by this Reference...
English Owners Manual - Page 3
... Proper Care of Your Scanner 2 Unpacking 2
Getting Started 3 Installing the BC244CLT 3
Operation 4 Controls and Functions 4 Scanning Overview 6
Clock Set-Up 7 Initial Clock Set-up 7 Reset the Clock Time 8 Set the Alarm Time 9 Turn the Alarm On or Off 10
Using the Scanner 11 Set the Squelch 11 Programming Tips 13 Programming Frequencies 14 Deleting a Stored...
English Owners Manual - Page 4
...BC244CLT 30-Channel Base Scanner. The BC244CLT scans programmed channels at a rate of Communication You can scan in the 29-54MHz, 137-174MHz, and
406-512MHz ranges 1 When the transmission ends, the scanner stays...radio stations, most 2-way communications do not transmit continuously (see Types of Communication below). If no responding transmission is detected, the scanning cycle resumes until ...
English Owners Manual - Page 5
... not use . s Avoid placing the unit in high-moisture environments such as
it could cause clock reset. to program, a Uniden representative should be reached at (800) 554-3988.
Monday through your Registration Form immediately. Read this list: s BC244CLT Base Scanner s Telescopic Antenna s AC Adapter (Model AC-144U) s This Reference Guide s Registration Form s Frequency...
English Owners Manual - Page 6
... ANT. it could cause clock reset.
3. Plug the Telescopic Antenna into any standard 120VAC wall outlet. Plug an optional external speaker (8-ohm) into an outlet controlled by a wall switch; Do not plug into the EXT. jack. If you are operating the scanner in . GETTING STARTED
Installing the BC244CLT
1. If your scanner receives strong...
English Owners Manual - Page 7
... Lockout is retained in the frequency. Press LOCKOUT again to view and set time.
6. Decimal Key Press to start scanning.
4 SCAN Key Press to enter the decimal point in memory. M Key
Steps down through the minutes in the clock mode, channels... for time entries and direct channel access with MANUAL key.
3. LOCKOUT Key Prevents scanning of the displayed channel. Also, use for...
English Owners Manual - Page 8
.... SQUELCH
Adjusts the squelch threshold. In Priority mode, the scanner samples the designated Priority Channel every 2 seconds. while in the weather mode.
14. MANUAL Key Stops scanning. VOLUME
Turn clockwise to scan the... Clock mode is still active when scanner is present.
12. Or, use for the factory setting.
5 ON/OFF Key Turns scanner on or off .
16. Turn counterclockwise to ...
English Owners Manual - Page 9
... press SCAN, the BC244CLT scans each programmed frequency for a.m.
When the scanning stops ...stays on that has been assigned as the transmission continues. If no responding transmission is active. L/O Indicator 24. Represents the current channel 01 through 30. 7-digit display that are locked out) at the rate of about 12 channels per second. As the unit scans, the word SCAN moves...
English Owners Manual - Page 11
... time directly by pressing the L/Mkeys.
3. Press AM/PM to complete the entry. The display stops flashing.
8 After the scanner has been turned on, to reset
the clock time, simply press and hold the TIME SET key. The display digits flash.
2. OR Enter the time by pressing the numeric keys...
English Owners Manual - Page 14
USING THE SCANNER
Set the Squelch 1. Turn SQUELCH fully clockwise to turn on the scanner.
3. Press ON/OFF to
the highest setting. 2. Adjust the VOLUME control until you can hear a steady noise.
11
English Owners Manual - Page 15
..., manually set squelch as follows: s Think of squelch as a gate. This raises the "Squelch Gate" so high that everything gets through - Now the "Squelch Gate" allows only strong signals through . 4.
This lowers the "Squelch Gate" so that only very strong signals can get through .
12 Set the SQUELCH control to AUTO for the factory setting. Turn SQUELCH fully counter clockwise...
English Owners Manual - Page 17
...), press 1, then 2 on the numeric keypad. Channel digits flash as you must program the channels (except weather frequencies). Programming Frequencies Before you can use your BC244CLT scanner, you make the entry.
14 Follow these steps: Example: Program 420.150 MHz into Channel 12. 1. Then press MANUAL again.
3. Type in the frequency...
English Owners Manual - Page 19
... next channel.
Channel information is automatically in non-volatile memory. If desired, you can press MANUAL repeatedly to stop scanning. About Memory Back-up Your BC244CLT has a convenient memory back-up to start scanning again.
16 Manual Mode Press MANUAL any active channel, except those channels locked out. To scroll through the channels...
English Owners Manual - Page 21
... country, you may not be able to find the active weather channel in low-lying areas.
Normally a higher location improves the reception. Weather Channel Scan The BC244CLT allows you to avoid this occurrence.
18
All weather channels transmit continuous broadcasts. Once the Weather Scan stops on a transmission, it remains on that channel, disrupting the...
English Owners Manual - Page 22
... like a dual watch function. If the signal stops for activity. Every two seconds, the scanner checks the priority channel for more than two seconds, normal scan operation resumes. To Set the Priority Channel Your BC244CLT has a default Priority Channel, set Channel 5 as the priority channel. 1. Press MANUAL to you activate Priority...
English Owners Manual - Page 26
.... Cleaning
s Disconnect the power to reset. Repairs s Do not attempt any repair...hear the entry tone for
that key. Contact
the Uniden Customer Service Center or take it may provide better reception... s Birdies are internally-generated signals inherent in the electronics of the receiver. If your scanner receives strong interference... Scan mode and no serviceable parts. A higher elevation may be ...
English Owners Manual - Page 27
... s Scan won 't power up.
s Press the SCAN key again. s Check to another wall outlet.
This could be in a fringe area.
You could require an optional multi-band antenna. s Move the ... Squelch control.
TROUBLESHOOTING
If your dealer or local electronics store. s Move the AC Adapter to see if 30 channels are locked out. s Check antenna connection. Check with your BC244CLT ...
English Owners Manual - Page 28
... it is correct and no active stations within range.
At Uniden, we'll take care of you with this unit, available accessories, or any matters regarding the
operation of finding an active channel.
Solution
s Adjust squelch to the threshold (Page 11).
Our Uniden representatives will be happy to return the unit for service, please...
English Owners Manual - Page 29
Band Coverage: Frequency Coverage:
Sensitivity (nominal) 12dB SINAD:
Channels: Scan Rate: Audio Output (nominal): Power Requirements: Antenna: External Jacks:
... Band
Above bands in accordance with FCC Rules and Regulations Part 15 Sub-part C as of date of optional accessories are all subject to change without notice.
26
TECHNICAL SPECIFICATIONS
Certified in 12.5kHz steps 0.3 µV 29-54 ...
English Owners Manual - Page 30
... be free from state to return it to you to state. Warrantor, at :
Uniden America Corporation Parts and Service Division 4700 Amon Carter Blvd Fort Worth, TX 76155 (800) 297-1023, 8 a.m. The Product should include all parts and accessories originally packaged with a new or refurbished unit. STATEMENT OF REMEDY: In the event...
Similar Questions
How Can I Factory Reset My Bc248clt Where There Is No Codes In It
(Posted by jamesallenholbrook1215 1 year ago)
My Squelch Does Not Work And I Can Not Program It Can You Tell Me Whats Wrong Wi
MY SQUELCH DOES NOT WORK AT ALL. I CAN NOT GET IT TO SCAN THROUGH THE CHANNELS OR PROGRAM IT.
MY SQUELCH DOES NOT WORK AT ALL. I CAN NOT GET IT TO SCAN THROUGH THE CHANNELS OR PROGRAM IT.
(Posted by nelllemaster 12 years ago)