Troy-Bilt TB675 Support Question
Troy-Bilt TB675 Support Question
Find answers below for this question about Troy-Bilt TB675.Need a Troy-Bilt TB675 manual? We have 1 online manual for this item!
Question posted by wsmharp on October 20th, 2015
The Head Will Not Turn.
The unit starts but the head will not rotate....looks as though some sort of drive cable has snappped?
Current Answers
Answer #1: Posted by Odin on October 20th, 2015 6:45 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,670
Member since:
April 10th, 2010 Points: 41,236,670
Replace the head--see https://www.youtube.com/watch?v=NPu2SQWCO4Q.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Troy-Bilt TB675 Manual Pages
Operation Manual - Page 1
... time of printing. Copyright© 2013 MTD SOUTHWEST INC, All Rights Reserved.
01/13 Operator's Manual
Electric Start Capable 4-Cycle Trimmer
TB675 EC
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil and Fuel 8 Starting and Stopping 10 Operation 12 Maintenance 13 Cleaning and Storage 17 Troubleshooting 18 Warranty 20
SAVE THESE...
Operation Manual - Page 2
... tank before filling the tank.
keep these instructions before operating the unit in property damage or injury to yourself or to the head, hands and feet.
• Carefully inspect the area before starting the engine. WARNING: Signals a SERIOUS hazard. All U.S. This unit is highly flammable and its constituents and
certain finished components contain or...
Operation Manual - Page 3
... level.
• The cutting head shield must be in a stable position while starting position whenever pulling the starter rope. Do not operate the unit without both handles or grips.
• Do not overreach. Do not operate the unit before starting . Do not operate the unit with loose or damaged parts.
• Turn the engine to off .
•...
Operation Manual - Page 4
...ear protection when operating this product. Keep away from the rotating rotor.
• KEEP BYSTANDERS AWAY
WARNING: Keep all... operation. SYMBOL MEANING
• ON/OFF STOP CONTROL ON / START / RUN
• ON/OFF STOP CONTROL OFF or STOP
&#...
• DO NOT USE E85 FUEL IN THIS UNIT
WARNING: It has been proven that may get extremely...turned off they remain hot for a short time.
• ...
Operation Manual - Page 5
.... (355 ml) Approximate Unit Weight (No fuel, with this unit. Shaft Grip
Muffler
Spark Plug
Starter Rope Grip Primer Bulb
ASSEMBLY TOOLS REQUIRED:
• #2 Phillips Screwdriver • 3/8" Socket
On/Off Switch
Handle Shaft Housing
Air Filter Cover
Throttle Control
Fuel Cap Choke Lever
Coupler
Oil Fill Plug
Cutting Head
Cutting Head Shield
Line Cutting...
Operation Manual - Page 6
....24 cm) from the end of shaft and shield equipped with the holes in place. ASSEMBLY
INSTALLING THE CUTTING HEAD SHIELD
WARNING: To prevent serious personal injury, never
operate the unit without the cutting head shield in the mount bracket. (Fig. 1)
2. Insert the bolt into the bolt hole and push it through the...
Operation Manual - Page 7
... (Fig. 3).
While firmly holding the attachment, push it straight into the
coupler until the release button snaps firmly into
the primary hole only.
Turn the knob clockwise to the unit. OPERATING THE COUPLER
The coupler enables the use of the coupler (Fig. 5).
90˚ Edging Hole (Trimmer Only)
Coupler
Fig. 3
Knob
Release...
Operation Manual - Page 8
... engine. Wipe up any oil that may have spilled. 7.
Check the oil level before starting the unit. Set the unit on the oil fill plug (Fig. 7). Reinstall the oil fill plug.
Pour the entire... of the correct type can cause premature engine wear and failure. DO NOT
overfill.
NOTE: This unit comes with gasoline. 6. Refer to the fuel tank. Unscrew the top of oil. 1. Unscrew ...
Operation Manual - Page 9
... fill hole on the container. Keep sparks and open flames at least 30 ft. (9.1 m) from the fuel container and
the fueling site before starting the engine.
9
Move the unit at a distance from fuel spray.
Using Fuel Additives Use a fuel additive, such as ethanol, methanol or MTBE (ether). Wipe up any spilled fuel...
Operation Manual - Page 10
...the engine to Position 3. To avoid
serious injury, the operator and the unit must be used during this time. Refer to turn the unit on. NOTE: There is in Position 3, squeeze and hold the On/...no need to Checking the Oil Level.
2. Move the choke lever to Fueling the Unit. the engine does not start . IF THE UNIT WAS RUN FOR 10-15 MINUTES AND THE ENGINE IS HOT... Slowly press and release...
Operation Manual - Page 11
... in Position 3, squeeze and hold the throttle control, move the choke lever to squeeze the throttle control. Move the choke lever to turn the unit on. Continue to squeeze the throttle control. Run the electric start accessory from the unit.
11. Continue to squeeze the throttle control. Move the choke lever to Fueling the...
Operation Manual - Page 12
...; Stand in the cutting head shield will cut thick vegetation • Forcing the line into objects such as walls or fence posts
DECORATIVE TRIMMING When trimming around trees, posts, fences, etc., rotate the whole unit so that it easily
contacts the grass without stopping the engine. Keep the right arm
slightly bent. •...
Operation Manual - Page 13
...the oil. Turn the bump knob counterclockwise to Changing the Oil. • Have the rocker arm clearance checked by an MTD authorized service dealer. Always allow the unit to the unit. FREQUENCY Every... eyelet (Fig. 16). Push
the line through the cutting head until the ends are unsure about 5 inches (12.7 cm) protrude from starting accidentally. DO NOT push the bump knob down while winding ...
Operation Manual - Page 14
... the crankcase. 4. CHECKING THE OIL LEVEL
WARNING: OVERFILLING THE CRANKCASE MAY
CAUSE SERIOUS PERSONAL INJURY. Look into the holes. NOTE: Make sure the O-ring is too low, add oil. Use a clean... or
table. Remove the spool cover (Fig. 18). 3.
Set the unit on the oil fill plug (Fig. 20). The cutting head shield should fill the window approximately halfway (Fig. 20). NOTE: Failure to...
Operation Manual - Page 15
...filter cover (Fig. 23).
Swing the air filter cover to cool before cleaning or maintaining the unit. Reinstall the air filter in detergent and water. Push the air filter cover back onto the ...left. Remove the air filter from the air filter housing (Fig. 23).
2. NOTE: Operating the unit without the air filter and air filter cover will flow freely and carry away more impurities. 1. Wash...
Operation Manual - Page 16
...turn the idle speed screw counterclockwise, 1/8 of the following conditions are true, take the unit to a qualified service dealer: • the engine will not idle, adjust the idle speed screw as follows: 1. Start... or dirty, replace it with a 5/8-inch socket, turning it from the cylinder head with a 5/8-inch socket, turning counterclockwise. Tighten the spark plug with a replacement part ...
Operation Manual - Page 17
...aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic.
Start the engine and allow it to Changing the Oil. Remove the spark plug and drain all... the engine to cool before cleaning or maintaining the unit.
If this is not possible, store the unit vertically with a soft cloth. Thoroughly clean the unit and inspect it for Use after Long-term Storage...
Operation Manual - Page 18
... Rewind the line Clean the inner reel and outer spool Open the cutting head and remove the welded section Rewind the line Stop the unit, push the bump knob and pull the line until 4 inches (102 mm... bound up The cutting head is dirty The line is welded The line is twisted
Not enough line is required, contact an authorized service dealer.
18 PROBLEM THE ENGINE WILL NOT START The fuel tank is empty...
Operation Manual - Page 20
...territories, except those sold or exported outside of the United States of America, its option, repair or replace,...Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, Guide Bars,
Cultivator Tines, Blades. TROY-...Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses,...
Similar Questions
I Have A Troy Bilt Lawn Tractor That Won't Start.
I've narrowed it down to the shifter ,forward, neutral, reverse mechcanism, when i wiggle it cranks ...
I've narrowed it down to the shifter ,forward, neutral, reverse mechcanism, when i wiggle it cranks ...
(Posted by carptr50 6 years ago)
Head Wont Stay On Shaft
how do u repair the trimmer so the head will stay on the shaft?
how do u repair the trimmer so the head will stay on the shaft?
(Posted by amandatackett29 8 years ago)
Troy-bilt Tb675 Overheating
My Troy-Bilt TB675 overheats after running for a short time. Is this common with these models ?
My Troy-Bilt TB675 overheats after running for a short time. Is this common with these models ?
(Posted by Anonymous-154291 8 years ago)
Oil For Troy-bilt Tb675
what kind of oil should I put in my Troy-Bilt TB675
what kind of oil should I put in my Troy-Bilt TB675
(Posted by herjeac 10 years ago)
