Troy-Bilt TB675 Support Question
Troy-Bilt TB675 Support Question
Find answers below for this question about Troy-Bilt TB675.Need a Troy-Bilt TB675 manual? We have 1 online manual for this item!
Question posted by bcooley500 on July 2nd, 2013
Remove Head
How do I remove the head so I can replsce it?
Current Answers
Related Troy-Bilt TB675 Manual Pages
Operation Manual - Page 1
... the warranty period, should only be found on the latest product information available at the time of printing. Operator's Manual
Electric Start Capable 4-Cycle Trimmer
TB675 EC
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil and Fuel 8 Starting and Stopping 10 Operation 12 Maintenance 13 Cleaning and Storage...
Operation Manual - Page 2
...and
certain finished components contain or emit chemicals known to the State of California to the head, hands and feet.
• Carefully inspect the area before fueling.
• Always ...spark arrestor, maintained in serious injury to yourself or to others .
Wash hands after handling. Remove rocks, broken glass, nails, wire, string and other reproductive harm. Failure to obey a ...
Operation Manual - Page 3
...unit. Refer to Cleaning and Storage. • Keep these instructions. SAVE THESE INSTRUCTIONS
3 The cutting head remains stationary when the engine is dusty.
• Wear heavy long pants, boots, gloves and ... muffler and spark arrestor. Make sure all moving parts. It will do the job. Carefully remove vegetation and other users. Keep a firm grip on both handles or grips.
• Do...
Operation Manual - Page 5
...; #2 Phillips Screwdriver • 3/8" Socket
On/Off Switch
Handle Shaft Housing
Air Filter Cover
Throttle Control
Fuel Cap Choke Lever
Coupler
Oil Fill Plug
Cutting Head
Cutting Head Shield
Line Cutting Blade
SPECIFICATIONS*
Engine Type Air-Cooled, 4-Cycle Displacement 30 cc (1.83 cu. We reserve the right to make changes at the time...
Operation Manual - Page 6
... and push it a minimum of 6 inches (15.24 cm) from the end of the shaft grip (Fig. 2).
4. Screws (2)
Use the following instructions if the cutting head shield is firmly in the operating position (Fig. 13), move
the handle to the type of the shaft grip (Fig. 2). 3.
Place it a minimum of 6 inches...
Operation Manual - Page 7
... and
damage to loosen (Fig. 3). 2. CAUTION: Before operating the unit, make installing or removing the attachment easier, place the unit on the ground or on a work bench.
NOTE: To...Primary Hole
Guide Recess
Upper Shaft Housing
Lower Shaft Housing
Fig. 5
7 Installing the Attachment
NOTE: Remove the protective cap and gray spacer from the upper and lower shafts prior to loosen (Fig. 3)....
Operation Manual - Page 8
...OVERFILLING THE CRANKCASE MAY
CAUSE SERIOUS PERSONAL INJURY. Change the oil according to Checking the Oil Level.
Remove the cap from the oil bottle. Set the unit on the oil fill plug (Fig. 7). ...to use clean oil of maintaining the proper oil level cannot be added before each use dirty oil. Remove the paper seal. This unit has a four- Use the bottle to measure the
correct amount of ...
Operation Manual - Page 9
... unit at a distance from the fuel container and
the fueling site before starting the engine.
9 Alcohol-blended fuel absorbs water. WARNING: Remove the fuel cap slowly to the unit's fuel tank.
Remove the fuel cap. 3. Definition of Blended Fuels Today's fuels are often a blend of gasoline and oxygenates such as 1% water in...
Operation Manual - Page 11
... stop (Fig. 8).
11 USING THE ELECTRIC START ACCESSORY
This unit can be started with step 3. NOTE: SQUEEZE and HOLD the throttle control for more information. Remove the electric start port (Fig. 12). The engine should start accessory for 2-5 minutes, or as needed .
The unit may be used during this time. Refer...
Operation Manual - Page 12
... ground while the unit is released. TIPS FOR BEST TRIMMING RESULTS • Keep the cutting head parallel to the ground. • Cut from the operator. • Do not trim wet grass or weeds.
CAUTION: Do not remove or alter the line cutting blade
assembly. NOTE: Some line breakage will make the unit...
Operation Manual - Page 13
...Fig. 16). 4. Turn the bump knob counterclockwise to Removing Old Trimming Line and Obstructions.
2. Push
the line through the cutting head until about these required maintenance procedures at 38 hours
MAINTENANCE...service dealer. • Check the spark plug condition and gap. Other types of the cutting head (Fig. 17). WARNING: Never use metal-reinforced line, wire, chain or
rope. These...
Operation Manual - Page 14
... fill plug (Fig. 20). Use a clean cloth to prevent debris
from the cutting head. 1. Push the spool cover onto the outer spool until the oil level is approximately...3. Removing Old Trimming Line and Obstructions If necessary, remove any old trimming line and/or obstructions from entering the oil fill hole. 2. Remove any old trimming line and/or obstructions. 4.
The cutting head shield...
Operation Manual - Page 15
... filter can result in the air filter housing (Fig. 23). Unscrew the cover screw completely. Remove the air filter from the air filter housing (Fig. 23).
2. NOTE: Operating the unit ... engine is not covered by the product warranty. NOTE: DO NOT overfill. Refer to spread and remove excess oil. 6. Cleaning the Air Filter
1. Reinstall the air filter in poor performance or can cause...
Operation Manual - Page 16
... (Fig. 24). 3. Refer to set the air gap at a time (as needed ) until snug. Reattach the spark plug boot. Remove the spark plug from the spark plug.
2.
ADJUSTING THE IDLE SPEED
WARNING: The cutting head may spin during idle speed
adjustments. Idle Speed Screw Fig. 24
0.025 in . (0.635 mm) (Fig. 25).
5.
Operation Manual - Page 17
... of the reach of the unit. Start the engine and allow it to Changing the Oil. Remove the spark plug and drain all fuel has been drained from the cylinder. 2. Dispose of any...engine to cool before cleaning or maintaining the unit.
Long-term Storage
1. Reinstall the fuel cap.
2. Remove the spark plug and put 5 drops of old fuel according to prevent unauthorized use or damage. •...
Operation Manual - Page 18
... line is twisted
Not enough line is extended
Stop the engine and clean the cutting head Refill the cutting head with new line Rewind the line Clean the inner reel and outer spool Open the cutting head and remove the welded section Rewind the line Stop the unit, push the bump knob and pull...
Operation Manual - Page 20
... SERVICE DEALER. TROY-BILT LLC
P.O. Tune-ups - Alteration of the safety features of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for rental expenses to modify any product previously manufactured. Box 361131, Cleveland, OH 44136-0019. MANUFACTURER...
Similar Questions
The Head Will Not Turn.
The unit starts but the head will not rotate....looks as though some sort of drive cable has snapppe...
The unit starts but the head will not rotate....looks as though some sort of drive cable has snapppe...
(Posted by wsmharp 8 years ago)
Troy-bilt Tb675 Overheating
My Troy-Bilt TB675 overheats after running for a short time. Is this common with these models ?
My Troy-Bilt TB675 overheats after running for a short time. Is this common with these models ?
(Posted by Anonymous-154291 8 years ago)
Remove Head On Tb575 Ec
I want to replace the head on my TB575 EC because it's broken. I have already taken the gear box off...
I want to replace the head on my TB575 EC because it's broken. I have already taken the gear box off...
(Posted by tamtmnguyen 9 years ago)
Head Quit Spinning. Found Out Gear Is Stripped Out But Cannot Find The Part.
Found out gear is stripped out but searched parts for this trimmer but could find no replacement par...
Found out gear is stripped out but searched parts for this trimmer but could find no replacement par...
(Posted by jamesbacon239 9 years ago)
Remove The Cutting Head
I want to know how to remove the cutting head of TB2044XP trimmer
I want to know how to remove the cutting head of TB2044XP trimmer
(Posted by jthannikary 10 years ago)