Home » Stihl » Lawn & Garden » Stihl MS 251

Stihl MS 251 Support Question

Find answers below for this question about Stihl MS 251.
Need a Stihl MS 251 manual? We have 1 online manual for this item!

Stihl Overview Questions Manuals Reviews Videos Research

Question posted by Plummerman1 on June 10th, 2022

Is There An Oil Adjustment On Ms271

is there a bar oil adjustment on.stihl ms 271? If so where is it?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on June 10th, 2022 9:42 PM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,621,300

1,100
points

https://editorsvine.com/adjust-the-oiler-on-stihl-ms-251/

Where is the oil adjustment on Stihl ms251 chainsaw?

Image result for Stihl MS 251 Oil Adjustment

The location of the oiler adjustment hole should be pointed on the instruction manual, but if you can't find it, it is usually right beneath the bar. Just look for a hole that has a flat screw-like thing inside.

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Stihl MS 251 Manual Pages

Instruction Manual - Page 2

...Leakage Test 89 RA_737_00_01_01 MS 231, MS 231 C, MS 251, MS 251 C q © ANDREAS STIHL AG & Co. Chain Lubrication 78 11.1 Pickup Body 78 11.2 Oil Suction Hose 78 11.3 Oil Pump 78 11.4... 24 5.4.1 Adjusting the brake cable 26 5.4.2 Brake cable Removing and Installing 27 5.5 Chain Tensioner 29 5.5.1 Quick Chain Tensioner 30 5.5.2 Chain Catcher 30 5.6 Bar Mounting Stud ...

Instruction Manual - Page 3

...Diaphragm 90 12.6.2 Inlet Needle 90 12.6.3 Pump Diaphragm 91 12.6.4 Lever on Throttle Shaft 92 12.6.5 Adjusting Screws 93 12.7 Adjusting the Carburetor 95 12.7.1 Basic Setting 95 12.7.2 Standard setting 96 12.8 Carburetor Carrier 97 12.9 ... Fuel Pump 107 12.11.5 Tank Housing 108 13. Servicing Aids 112 2 MS 231, MS 231 C, MS 251, MS 251 C Special Servicing Tools 110 14.

Instruction Manual - Page 5

... dispose of STIHL press fluid, b 14. The specifications must be tightened to be performed outdoors only. Storing and disposing of oils and fuels Collect fuel or lubricating oil in the ... 4 MS 231, MS 231 C, MS 251, MS 251 C Always perform leakage test after removal. Do not cut open fuel hoses with the connector, preferably by the STIHL part number, the { logo and the STIHL parts ...

Instruction Manual - Page 6

... at gauge pressure: Operation of tank vent at gauge pressure: Fuel: 0.8 bar 0.5 bar as specified in instruction manual Air gap between ignition module and fanwheel: Spark plug (resistor type): Electrode gap: 0.30 (+ 0.05/- 0.10) mm NGK CMR 6 H 0.5 mm Speed-controlled Ematic oil pump Oil delivery rate: 8.0 (+/3.0) cm3/min at 10,000 rpm MS 231, MS 231 C, MS 251, MS 251 C 5 2.

Instruction Manual - Page 7

...to use a torque wrench. 2.5 Tightening Torques DG and P (Plastoform) screws are installed for bar / engine housing 16.0 (repair solution) P 5x18 Cover, chain brake / engine housing 4.0... 6.0 D 4x16 Oil pump 4.0 M 5x16 Muffler / cylinder 10.0 M 8x1 Flywheel / crankshaft 28.0 P 4x10 Retainer 1.0 Q B 2), 3) 2) 1), 3) 1), 3) 1), 3) 2), 3) 4) 6 MS 231, MS 231 C, MS 251, MS 251 C

Instruction Manual - Page 8

...not mix up screws with medium strength Loctite 242 or 243 before reinstalling. MS 231, MS 231 C, MS 251, MS 251 C 7 Fastener Thread size For component Torque Nm Remarks Screw Screw Screw ... 2) Micro-encapsulated screws 3) Waxed screws 4) Degrease crankshaft/flywheel and mount oil-free Q) QuickStop Super B) Quick chain adjuster Use the following procedure when refitting a DG or P screw in an ...

Instruction Manual - Page 11

lockout lever not depressed Brake cable overtensioned Remedy Readjust brake cable Reconnect or replace brake cable Adjust brake cable Adjust brake cable 10 MS 231, MS 231 C, MS 251, MS 251 C Condition Cause QuickStop Super Coasting brake does not disengage even though lockout lever is depressed Brake cable stretched Brake cable disconnected or broken QuickStop Super ...

Instruction Manual - Page 12

... worn Install new oil pump Machine losing chain oil Oil pump damaged or worn Oil suction hose connection damaged Engine housing cracked Install new oil pump Install new oil intake hose Install new engine housing Oil pump delivers insufficient oil Oil pump damaged or worn Worm driver is loose Install new oil pump Install new worm MS 231, MS 231 C, MS 251, MS 251 C 11 rectify...

Instruction Manual - Page 14

... Cause Remedy Starter mechanism is very dirty Thoroughly clean complete starter mechanism At very low outside temperatures: Lubricating oil on rewind spring becomes viscous (spring windings stick together) or moisture has got onto the rewind spring (spring...halogenated hydrocarbons), then pull rope carefully several times until normal action is restored MS 231, MS 231 C, MS 251, MS 251 C 13

Instruction Manual - Page 15

... necessary. too much oil Use correct mixture of fuel and oil Incorrect air gap between... new flywheel Irregular spark Check operation of adjustment - If sooting keeps recurring, check air filter Fuel/oil mixture - key in flywheel has sheared ... and fit new spring if necessary Spark plug sooted, smeared with oil Clean the spark plug or replace if necessary. 3.5 Ignition System Condition...

Instruction Manual - Page 17

... opened too wide by Reset idle speed screw (LA) high idle speed screw (LA) correctly Oil seals/engine pan leaking Seal or replace oil seals/engine pan Throttle shutter does not close Install new carburetor Engine stops while idling Idle jet bores... the clutch springs or install new clutch Clutch spring hooks broken Replace the clutch springs 16 MS 231, MS 231 C, MS 251, MS 251 C

Instruction Manual - Page 18

...carburetor Pump diaphragm damaged or fatigued Fit new pump diaphragm Ignition timing wrong, flywheel out of adjustment - low power Remedy Clean air filter or replace if necessary Throttle shutter not opened fully Tank... and choke shaft, service or replace if necessary MS 231, MS 231 C, MS 251, MS 251 C 17 Condition Cause Engine speed drops quickly under Air filter dirty load -

Instruction Manual - Page 19

... system Condition Cause Engine does not start easily, stalls Oil seals in fan housing dirty Clean air inlet on the...oil seals Inspect engine pan, re-seal or replace if necessary. Clean bore or install new manifold. Air filter - Fuel system - 3.7 Engine Always check and, if necessary, repair the following parts before looking for faults on fan housing 18 MS 231, MS 231 C, MS 251, MS 251...

Instruction Manual - Page 21

...one side and disconnect it . - The braking time is in terms of the machine. 20 MS 231, MS 231 C, MS 251, MS 251 C Troubleshooting, b 3.2 - the chain must come areas on inside diameter and/or parts of.... : Take out the screws (1). : Remove the cover (2). 219RA049 TG Machines with chain oil, chips, fine particles of abrasion, etc.) and smoothing of the friction surfaces of the brake...

Instruction Manual - Page 27

... operation of the coasting brake. - Troubleshooting, b 3.2 TOP 2310RA043 TG : Attach the spring (1) to the brake lever (arrow). 26 MS 231, MS 231 C, MS 251, MS 251 C Reassemble all other parts in the reverse sequence. 1 2310RA028 TG a 0001RA456 TG 5.4.1 Adjusting the brake cable The turns of the brake spring must rotate freely. - Press down the lockout lever (1) and...

Instruction Manual - Page 28

Reassemble all other parts in that position. Disconnect the brake spring, b 5.4 1 - Turn adjusting screw counter- Remove the carburetor, b 12.5 - Check the brake cable (1) and retainer (2), replace if necessary MS 231, MS 231 C, MS 251, MS 251 C 27 Take care not to reduce free travel . 1 1 - The brake band (1) must locate snugly against engine housing (arrows) and the ...

Instruction Manual - Page 29

... cable (2) into its offset is next to the recess (arrow) and then remove it from the retainer (4). : Fit the adjusting screw (1) and wind it home until the gap between the tank housing and engine housing to the right of the fuel hose ... hook (4) first, through the bore (arrow) in the engine housing. 1 2 : Push the insert (1) with the housing ribs. 28 MS 231, MS 231 C, MS 251, MS 251 C

Instruction Manual - Page 34

This makes adjustment of leaks. Moreover, the transition from idle speed to part or full throttle is ... exhaust port. : Fit the screws (2) - 2310RA072 TG 2310RA074 TG 6.2 Leakage Test Defective oil seals and gaskets or cracks in place. 2310RA079 TG a 2710RA164 TG 2310RA073 TG MS 231, MS 231 C, MS 251, MS 251 C 33 The engine can be checked thoroughly for leaks with the pump 0000 850 1300....

Instruction Manual - Page 111

... piston pin Adjusting air gap between the ignition module and flywheel Installing rewind spring Attaching springs Leakage Test Protecting the oil seal (clutch side) Installing oil seal (clutch side/ignition side) Spark plug 1) Protecting the oil seal (ignition side) Clamping machine to assembly stand Testing ignition system Testing ignition system 110 MS 231, MS 231 C, MS 251, MS 251...

Instruction Manual - Page 112

...Adjusting the carburetor IS-P screws Detaching springs on for screwdriver (adjusting carburetor) Removing pickup body Remarks: 1) Use for repairs Removing oil seals Removing oil seals Removing oil seals Pull off the limiter cap. No. Jaws (No. 3.1) - Removing bar... 893 8800 Application Rem. MS 231, MS 231 C, MS 251, MS 251 C 111 Sleeve 23 Screwdriver 24 Screwdriver bit, T 27 x ...