Sharp ER-A320 Support Question
Sharp ER-A320 Support Question
Find answers below for this question about Sharp ER-A320.Need a Sharp ER-A320 manual? We have 2 online manuals for this item!
Question posted by Anonymous-174118 on May 17th, 2023
Printing Report
When I try to print the z report it does not print. Don't know if doing it wrong.
Current Answers
Answer #1: Posted by HelpHero on May 17th, 2023 12:03 PM
HelpHero
Member since:
September 3rd, 2022 Points: 523,400
Member since:
September 3rd, 2022 Points: 523,400
There are a few things that could be causing the Z report to not print. Here are a few things to try :
1. Make sure that the printer is turned on and properly connected to the Sharp ER-A320.
2. Check the paper roll and ensure that there is enough paper left for printing the report.
3. Verify that the printer settings are configured to print the Z report. You can check this by accessing the printer settings menu in the Sharp ER-A320.
4. If the above steps don't work, try turning off the Sharp ER-A320 and then turning it back on again. This will sometimes reset any issues that may be causing the Z report to not print.
If none of these steps solve the problem, you may need to contact your local support team for further assistance. They will be able to help you troubleshoot the issue and find a solution.
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers.
Helphero
Answer #2: Posted by SonuKumar on May 17th, 2023 9:55 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,568,330
Member since:
May 9th, 2021 Points: 16,568,330
https://www.manualslib.com/manual/995172/Sharp-Er-A320.html
Service manual available
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Sharp ER-A320 Manual Pages
Programmer Manual - Page 1
...
This document has been published to change without notice. The contents are important for maintaining the safety of the set . SERVICE (SRV) MODE 1 CHAPTER 2. ELECTRONIC CASH REGISTER
MODEL ER-A320
(For "U" & " A " version) SRV KEY: LKGIM7113RCZZ PRINTER: UCR-812A
CONTENTS
CHAPTER 1. OP X/Z X1/Z1, X2/Z2 MODE 22
Parts marked with specified ones for after...
Programmer Manual - Page 2
... operational state after a lockup has occurred. The ER-A320 printer will cycle and print the following on the
journal
2
[JOB# 900...ER-A320 printer will cycle and print the following on the
journal
1
3. CHAPTER 1. Reading of the SRV mode program
List of program report
JOB#
REPORT NAME
900
SRV mode program full item report (Not included the keyboard layout)
950 Keyboard layout report...
Programmer Manual - Page 3
[JOB# 950]
Keyboard layout programming report Key operation
SRV mode
950 @/FOR
CA/AT
PGM mode
9950 @/FOR
CA/AT
Key code / Key position code
Key is not stored.
Programmer Manual - Page 4
... of date Yes No
904-A
0
5
4
#904-B : 1. Tax is zero
2. TAX system
1. Gross Tax 4 and refund Tax 4 total print on X/Z report 1. Nex Tax 4
905-A
Print
Print Skip
Print Skip Print Skip
0
5
1
2
3
Print
4
Print
Skip
Skip
5
Print
6
Skip
Skip
7
#905-B : 1. Taxable 4 SBTL
2. "00"key or "000" selection "00"key
"000"key
2. Service mode programming
The following...
Programmer Manual - Page 5
... totalizer on X report
GT1(NET)
GT2(+)
Skip Skip
Print
Print
Skip Print
GT3(-) Skip Print Skip Print Skip Print Skip Print
908-B
0
1
2
3
4
5
6
7
5
#908-C : 1. Minus Dept./PLU Disable Enable
#907-D : Not used (Fixed at "0")
[JOB#908] MRS = 0700
#908-A : GT print on Z report
GT1 (NET) Print
Skip
GT2(+) Print Skip Print Skip
GT3(-) Print Skip Print Skip Print Skip Print Skip...
Programmer Manual - Page 6
...Content of VP
NOTE : Must turn to MGR mode and depress
PRINT keys to escape validation
2. SBTL Print SBTL print
No No
Yes
No Yes
Yes
3. off 2sec. Key catch sound... mode Enable Disable
914-C
0
5
2
#914-D : 1. Non-add code entry Disable/Enable
1. CHECK CASHING
Enable
Disable Enable
Disable
Disable Enable
3. ST%, ST(-) as many times needed /operation only once Unlimited Once only...
Programmer Manual - Page 7
... total on 916-D
general report general report
general report
Print
Print Skip
Print Skip Print Skip
05 1 2 3
Print
Print
4
Skip
Skip
5
Print
6
Skip
Skip
7
[JOB#917] MRS = 0000
#917-A : 1. Print CHK
PLU's on
SBTL (NET1) on CHANGE on X/Z report
917-D
Print
Print Skip
Print Skip Print Skip
0
5
1
2
3
Skip
Print Skip
Print
4
Skip
5
Print
6
Skip
7
[JOB#918...
Programmer Manual - Page 8
... TAX3 SHIFT TAX4 SHIFT (Reserved) PRINT RCPT VOID REFUND %1 %2 (-)1 (-)2 TAX AUTO AUTO2 (Reserved) (Reserved) CHECK CHARGE1 CHARGE2 CONV1 CONV2 CONV3 CONV4 (Reserved) RA PO (Reserved) DEPT# NS ESCP DEPT...930 ~ 931] MRS = 0000
RESET REPORT COUNTER
919-D
0
5
1
Job#
@/FOR
"0000" ABCD CA/AT
Initial value of Z counter
JOB# 930 931
Z1 report counter Z2 report counter
Function
[JOB#942, 943, ...
Programmer Manual - Page 10
...
JOB# 1100 1200 1300 2700 2900
REPORT NAME Department program report PLU program report Other program report Tax program report Auto key program report
Direct key entry
JOB# CA/AT PLU
REPORT NAME PGM mode program report (Not included the PLU program report and Auto key program report) PLU program report
[JOB#1100] : Department program report
Key operation
1100
@/FOR
XX
Start...
Programmer Manual - Page 11
...Till timer CA/AT
[JOB#1300] : Other program report
Key operation
1300 @/FOR
CA/AT
PLU code / Dept...Limitation of entry digit for RA (JOB#2312) Limitation of entry digit for PO (JOB#2312) Programming for CA (JOB#2320) Limitation of entry digit for...2322) Programming for CH (JOB#2320)
Limitation of entry digit for CHECK CASHING (JOB#2321)
Limitation of entry digit for CHECK CHANGE (JOB#2321)
...
Programmer Manual - Page 12
[JOB#2700] : Tax program report
Key operation
2700 @/FOR
CA/AT
[JOB#2900] : Tax program report
Key operation
2900 @/FOR
CA/AT
Tax table
Tax rate Lower taxable amount
Auto key No. (JOB#2900) No./ Stored key position code
Marks the end of the key sequence
Programmer Manual - Page 13
...
Conversion rate(JOB#1310) Limitation of entry digit for RA (JOB#2312) Limitation of entry digit for PO (JOB#2312) Programming for CA (JOB#2320) Limitation of entry digit for CK (JOB#2322) Programming ... digit for CH2 (JOB#2322) Programming for CH2 (JOB#2320)
Limitation of entry digit for CHECK CASHING (JOB#2321)
Limitation of entry digit for CHECK CHANGE (JOB#2321)
Limitation of entry digit for CID...
Programmer Manual - Page 14
ALL Single item
@/FOR
XXX End No. code(JOB#1200) Tax status (JOB#2210-B,C,D,E,F) Amount entry type(JOB#2210-G) Unit price(JOB#1210)
Sign(JOB#2210-A) / Unit price(JOB#1210) PLU
Tax rate Lower taxable amount
PLU code / Dept. Tax table
[PLU] : PGM mode program report
Key operation
XXX Start No.
Programmer Manual - Page 15
... (limit) preset
2112
No change
@/FOR
XX
@/FOR
DEPT.
CODE
YYYYYYY price
#/TM/ SBTL
For the next DEPT.
A : ltem validation printing
A
Non compulsory
0
Compulsory
1
B : SICS Function
B
Normal
0
Single item cash sale
1
C : Dept. CODE
#/TM/ SBTL
For the next DEPT. type
C
Normal
0
HASH
1
D : AmDunt entry type
D
Inhibited
0
Open
1
Preset
2
Open and...
Programmer Manual - Page 17
... No. 1 2 3 4
Function (-) 1 (-) 2 %1 %2
A : Sign
A
+
0
-
1
Not available for (-)1 and (-) 2
B : Not used (Fixed at "00000")
H : Entry of amount tended
H
Non compulsory (Cash,
Check) Inhibit (CH1 to 8. Entry range, system :A x 10B
MRS = 17 ((-) 1, (-) 2, TAX) 18 (RA, PO, CA2, CK, CH1, CH2)
[JOB#2320]
MEDIA KEY PROGRAMMING
2320
@/FOR
No change
XX
@/FOR
ABCDEFGH
#/TM/ SBTL
CA...
Programmer Manual - Page 18
... (Fixed at "000")
D : Zero skip in Transaction report
D
Yes
0
No
1
E : Zero skip in REG mode
G
Enable
0
Disable
1
H : Not used (Fixed at "0") X : 2
MRS = 00000000
A, B, C : Not used (Fixed at "000")
D : Printing of the number of purchases D
No
0
Yes
1
E : Time print
E
Yes
0
No
1
F : Printing of journal
F
Full print
0
Journal Select
1
G, H : Not used (Fixed at "00...
Programmer Manual - Page 23
... reports.
Print report
In the table below those reports marked with a circle "O" can be printed by the standard machine and those marked with an asterisk " " can be printed by entering the start number has only to be specified by the ECR. 1) OP X/Z reports (individual clerk reports) 2) X1/Z1 reports (Daily sales total X and Z reports) 3) X2/Z2 reports (Periodic total X and Z reports...
Programmer Manual - Page 24
... reach the maximum amount. This means that when the totalizer overflows once. code
DEPT#
To read respective reports, it is printed. the overllow mark (for the totalizer concerned.
The overflow mark may be printed on X or Z reports exceeds a programmed limit, the indication mark (overflow mark) is necessary to follow the procedure below. This occurs...
Service Manual - Page 1
... OPTIONS 4 CHAPTER 3.
SHARP CORPORATION
This document has been published to change without notice. SPECIFICATIONS 1 CHAPTER 2. RESET AND MASTER RESET 5 CHAPTER 4. SERVICE MANUAL
ELECTRONIC CASH REGISTER
MODEL ER-A320
SRV Key : LKGIM7113RCZZ PRINTER : CR-812A (For "U" version)
CONTENTS
CHAPTER 1. SRV. CIRCUIT DIAGRAM & PWB LAYOUT 13 PARTS GUIDE
Parts marked with specified ones...
Service Manual - Page 2
This is a "Table of cash register and scale manuals on the net
http://the-checkout-tech.com : the biggest supplier of Contents preview" for quality assurance
The full manual can be found at http://the-checkout-tech.com/estore/catalog/
We also offer free downloads, a free keyboard layout designer, cable diagrams, free help and support.
Similar Questions
How To Fix The Problem Of Over Limit Sign Of Sharp Cash Register Model No. Er-a5
how to fix a problem of over limit sign on cash register of sharp of model no.ER-A520
how to fix a problem of over limit sign on cash register of sharp of model no.ER-A520
(Posted by parinpatel0033 5 years ago)
Cash Register Keys.
which key opens the cash register drawer? We only have one key which cuts it on and off but it doesn...
which key opens the cash register drawer? We only have one key which cuts it on and off but it doesn...
(Posted by Ajklove22 7 years ago)
Sharp Cash Registers Pos Er-a750
two cash registers the master reads ram error the second register blank screan key boards do nothing...
two cash registers the master reads ram error the second register blank screan key boards do nothing...
(Posted by Dearl001 8 years ago)
How To Get Daily Reports On A Sharp Er-a320 Cash Register
(Posted by bartbAnu 10 years ago)
My Sharp Er-a410 Cash Register Is Frozen With Error Message Tend Compel. Help
my Sharp ER-A410 cash register is frozen with error message tend compel. It is totally froze and I e...
my Sharp ER-A410 cash register is frozen with error message tend compel. It is totally froze and I e...
(Posted by lhasatrade 11 years ago)