Question posted by burunghantu25 on July 2nd, 2021
Start Button
Current Answers
Answer #1: Posted by SonuKumar on July 2nd, 2021 8:55 PM
Common solutions for: Washer won't start
01 - Main Control Board
The main control board might be defective. However, the main control board is rarely at fault for this symptom. Before replacing the main control board, first check all of the more commonly defective parts.
02 - Incoming Power Problem
The electrical outlet may not be getting power. To determine if the outlet is getting power, try plugging something else into the outlet. If the outlet is not getting power, check the home circuit breakers or fuses.
03 - Power Cord
First ensure that power is getting to the electrical outlet. If the electrical outlet is receiving power, but the washer won't start, the power cord might be defective. However, this is very rare. To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.
04 - Door Lock
The door lock secures the washer door shut during operation. Once the washer door is closed, the washer can begin operating. If the washer door is not latched shut, the door switch will prevent the washer from operating. If the door lock is defective, the washer will not spin or start. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it. To determine if the door lock has failed electrical Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it. To determine if the door lock has failed electrically, consult your washer's wiring diagram and use a multimeter to test each of the door lock switches for continuity.
https://www.youtube.com/watch?v=ol_sukAhSTw
https://www.youtube.com/watch?v=ol_sukAhSTw&t=40s
https://www.youtube.com/watch?v=ol_sukAhSTw&t=47s
https://www.youtube.com/watch?v=ol_sukAhSTw&t=140s
https://www.youtube.com/watch?v=ol_sukAhSTw&t=263s
https://www.youtube.com/watch?v=ol_sukAhSTw&t=337s
https://www.youtube.com/watch?v=WbbjCRUAPXQ
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Samsung Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
General Support
... without Newsletter Registration. Beginning Installation A Pop-Up box should automatically start and detect if both ActiveSync and Outlook are already installed on Microsoft...installed. On the License Agreement window, check the button "I Install Microsoft's ActiveSync For My SGH-i607? ... How Do I accept the terms..." (This is just for reference and will not affect any settings.) Choose... -
General Support
... the categories below : 1. Press and hold down the Voice Command button until a beep is it . Speak the contact name, command or phone number digits in a ...off Calendar What are not sure which number to call, say "one number for the beep before starting to call . What's my next appointment? Voice Command software automatically voice activates all contacts ... -
General Support
...) into the red reset hole, located just below the left soft key Note: This... From the Today screen, tap on Start Tap on Settings Tap on the Phone ... All Data Enter the lock code into the Password field Tap ...'s internal memory by using the Reset button in conjunction with the Action key. ...factory default settings (which only restarts the machine while maintaining all information and settings from...
Similar Questions
start button just beeps machine does not start. no error codes lid switch was replaced
my machine is about 3 years old and is throwing me a te error code. This would indicate a thirmister...
gas dryer will not start; control panel comes on but that is all. main control box replcad is there ...
I paused my washing machine and left the house for a few hours forgetting to restart the machine. Wh...