Ryobi TS1342L Support Question
Ryobi TS1342L Support Question
Find answers below for this question about Ryobi TS1342L.Need a Ryobi TS1342L manual? We have 4 online manuals for this item!
Question posted by Anonymous-52168 on February 25th, 2012
Does It Slide?
The person who posted this question about this Ryobi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Ryobi TS1342L Manual Pages
English Manual - Page 1
.... OPERATOR'S MANUAL
10 in.
Thank you years of rugged, trouble-free performance. WARNING: To reduce the risk of operation, and operator safety.
Compound Miter Saw
TS1342L -
English Manual - Page 2
... and exclusions may not be covered by the limited warranty for the balance of batteries, power tool accessories are warranted for ninety (90) days. This warranty only covers defects arising under state ...Box 1207, Anderson, SC 29622-1207, by calling 1-800-525-2579 or by returning the power tool to you may either repair or replace any charge to the dealer from misuse, abuse, neglect,...
English Manual - Page 3
...and benches invite accidents. All visitors should be carefully checked to determine that it to this tool.
GUARD AGAINST ELECTRICAL SHOCK by the cord or yank it will do a job... injury.
USE THE RIGHT DIRECTION OF FEED. READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Keep the work into moving parts. Feed work area well lit.
KEEP CHILDREN AND VISITORS...
English Manual - Page 4
...oil and grease.
Do not stack more than the other parts may slip, walk or slide while cutting long or heavy boards.
Always use blade washers or blade bolts ... connect the equipment-grounding conductor to install the proper outlet. GENERAL SAFETY RULES
Inspect TOOL CORDS periodically. Repair or replace a damaged or worn cord immediately. Always use common sense. ...
English Manual - Page 5
...Do not perform any use of the saw) to instruct other users. g) Disconnect power (or unplug tool as applicable)
before changing blade or servicing. If you have damaged, missing, or failed parts replaced before... freehand. NEVER leave the saw unattended while connected to a power source.
TURN OFF TOOL and wait for saw blade to come to a complete stop. f) Turn off the power switch...
English Manual - Page 6
...injury or damage, avoid contact with side shields and, as necessary, a full face shield when operating this tool. SYMBOLS
Some of the following symbols may be used on this product.
Safety Alert No Hands Symbol Hot ...that involve your hands away from the blade will allow you to operate the tool better and safer. To reduce the risk of injury, user must read and understand operator's manual before ...
English Manual - Page 7
... signal words and meanings are intended to explain the levels of any power tool can result in foreign objects being thrown into your eyes, which can result...we suggest you do not understand the warnings and instructions in minor or moderate injury. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields. Always use eye protection which , if...
English Manual - Page 9
...the front of a workpiece usually caused by cutter blades when the workpiece is being dropped into the tool first. A metal piece, slightly thinner than the saw blade during a ripping operation. Set The ... by the workpiece being done.
Workpiece or Material The item on which a blade or cutting tool is bent (or set) outward from being kicked back toward operator.
Non-Through Cuts Any ...
English Manual - Page 11
....
14 AMP MOTOR
The saw at which the cut materials up to move the miter saw
See Figure 2. MITER FENCE
The miter fence on the tool and in . thick or 6 in .
Use the hex key end when installing or removing blade and the phillips end when removing or loosening screws.
The...
English Manual - Page 12
... key in the switch trigger. The miter lock handle securely locks the saw at 0°, 15°, 22-1/2°, 30°, and 45°.
TOOLS NEEDED
The following tools (not included) are needed for making adjustments or installing the blade:
Combination Wrench (2) 10 mm ,12 mm
hex key 5 mm
FRAMING SQUARE
COMBINATION...
English Manual - Page 13
... WRENCH
WORK CLAMP
Fig. 6
WARNING:
The use of the tie wrap.
Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
Do not discard the packing...or accessories not listed might be hazardous and could cause serious personal injury. NOTE: This tool is factory set for accurate cutting. LOOSE PARTS
The following items are damaged or missing, ...
English Manual - Page 14
... check the workbench after mounting to make sure the compound miter saw is not secured to a work surface before any tipping, sliding, or walking is securely mounted to heed this tool until assembly is shown in serious personal injury. Failure to a workbench or an approved workstand. WARNING:
Always make sure that no...
English Manual - Page 15
...
See Figure 10. Depending on the miter saw blade. The work clamp to secure the workpiece prior to open the mouth of the bag and slide it , squeeze the two metal clips to making the cut.
A dust bag is provided for emptying, simply reverse the above procedure. To remove the dust...
English Manual - Page 19
...
Fig. 17
Miter lock plate
MITER TABLE
FRAMING SQUARE
Miter lock Handle
VIEW OF Blade NOT SQUARE WITH FENCE, ADJUSTMENTS ARE REQUIRED Fig. 20
19 Slide the other leg of the square against the fence. After squaring adjustments have been made, it may be parallel as shown in transport position. ...
English Manual - Page 32
...
Now that you have purchased your nearest Authorized Service Center. The model number of this tool will be found on how often you call 1-800-525-2579 for your nearest Authorized Service Center. Compound Miter Saw
TS1342L - Your risk from chemically-treated lumber. Please call or visit. You can also check our...
Repair Sheet - Page 2
COMPOUND MITER SAW - MODEL NUMBER TS1342L
11 8
12 13 14
15 16 17
18
21
19
20
69
70 76 68
75 67
74
71
73
72 77 66
22
23
27 24
29 30
65
25
26
33
28
35
34 36
31 32
52 51
37
46 45 44 43 42
41
38
40
50
53
49
39
48
47
78 64 63
62
59 54
55
FIGURE A
61 60
56
57 58 10 9 7 6 5 34
2 1
RYOBI 10 in.
Repair Sheet - Page 3
... Nut (M10 1 * Fixed Screw (M10 x 20 mm 1 * Lock Nut (M12 2 * Washer (M12 1 Arm 1 Spindle Lock Pin 1 E-Ring 1 Compression Spring 1 Output Spindle Assembly (Inc. MODEL NUMBER TS1342L
The model number will be found on a plate attached to the motor housing. Key Nos. 59-61 1 No Hands Warning Label 1 Retaining Ring 1 Roller 1 Torsion...
Repair Sheet - Page 4
COMPOUND MITER SAW - MODEL NUMBER TS1342L
8
10
7
9
5
6
11
43
5
14
12
9
15
4
16
3
13 7
18 17
19
5
20
6
2
5
1
22
21
23
24
42
25
26
40
39
38
11
37
44
41
36
27
7
5 28
FIGURE B
34 35 34
33
29
32
30
31 RYOBI 10 in.
Repair Sheet - Page 5
... (M10 1
* Washer (M10 2
* Spring Washer (M10 1
Base 1
Miter Scale 1
Wear Pad 5
"No Hands Zone" Label 2
"No Hands Zone" Boundary Line 2
Base Assembly (Inc. MODEL NUMBER TS1342L
The model number will be found on a plate attached to the motor housing.
Hd 4
25 503118000
Bevel Lock Knob 1
26 089100212700
* Washer (M10 1
27 518105400...
Repair Sheet - Page 6
RYOBI 10 in. MODEL NUMBER TS1342L YELLOW LEAD
BRUSHES
SWITCH
YELLOW LEAD
YELLOW LEAD BLACK LEAD
BROWN LEAD
MOTOR
POWER CORD
WHITE LEAD
WIRING DIAGRAM
WHITE LEAD COMPOUND MITER SAW -
Similar Questions
Ryobi Ts1342l
I am searching for a price on lower guard for my Ryobi TS1342L
I am searching for a price on lower guard for my Ryobi TS1342L
(Posted by maristegui 4 years ago)
How Do I Replace The Spring On My Ts1342l 10 Lower Blade Guard
(Posted by golfesxu 10 years ago)
How To Operate The Slide Bar.
I loosened the Slide Lock Knob.Bevel lock lever is opened. The Slide Bar seems to be stuck. No slidi...
I loosened the Slide Lock Knob.Bevel lock lever is opened. The Slide Bar seems to be stuck. No slidi...
(Posted by billgovan45 12 years ago)
Lower Blade Guard Ts1342l Miter Saw
How do I replace the spring on my TS1342L 10" lower blade guard?
How do I replace the spring on my TS1342L 10" lower blade guard?
(Posted by MRELVIS 12 years ago)