JET Tools J-41002 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools J-41002 manuals!
Problems with JET Tools J-41002?
Ask a Question
Free JET Tools J-41002 manuals!
Problems with JET Tools J-41002?
Ask a Question
Popular JET Tools J-41002 Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
Belt (2x42") and Disc (8") Sander
Model J-41002
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-577004 Revision B1 03/2014 Copyright © 2014 JET
User Manual - Page 2
... Period 90 Days -
Heavy-Duty Air Tools; Woodworking Machinery used for commercial or industrial purposes default to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of our tools needs service or repair, please contact Technical Service by JPW Industries, Inc. Hand Tools
NOTE: JET is constantly adding new products. References...
User Manual - Page 4
... State of parts, mounting and any other purposes, JET disclaims any ...specifically designed to cause cancer, birth defects or other part that it on.
15.
Make certain the machine is damaged should be properly repaired or replaced.
18. Provide for the machine to a supporting...manual before attempting assembly or operation.
2. Failure to determine that is properly grounded.
13. Replace...
User Manual - Page 5
...tool will do a job for lubricating the machine and changing accessories.
29. However, combining wood dust and metal filings can tear the disc/belt. Follow instructions..., place the workpiece against the abrasives or other moving parts. Abrasive discs must be used in the proper direction... down to remove chips or debris - do this manual:
This means that can be stored in minor injury...
User Manual - Page 6
... notice, without incurring obligations.
6 Introduction
This manual is provided by JET covering the safe operation and maintenance procedures for a JET 2x42x8 Belt and Disc Sander. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Specifications
Model Number...J-41002 Stock Number...577004 Belt Size (in...
User Manual - Page 8
... with the following parts list to your distributor.
Failure to your container with trunnions 1 Miter Gauge 1 Dust Chute 6 Phillips Pan Hd. Unpacking
Open shipping container and check for assembly, maintenance and safety instructions. Report any damage immediately to comply may cause serious injury.
8 Compare the contents of this manual before attempting set-up or...
User Manual - Page 9
...Installing Belt Table
1. Position the bracket of the sander and from any loose parts... with a soft cloth moistened with a good quality paste wax. Assembly
Tools needed , the sander can be bolted to walk or slide during assembly...all the way into the hole. If the sander has a tendency to a supporting surface. Unscrew the stud. The dust chute for general maintenance. angle
Sander must...
User Manual - Page 11
... 9
11
Check with insulation having an equipment-grounding conductor and a grounding plug.
If repair or replacement of power and overheating. The temporary adapter should only be used to connect this plug to a twopole receptacle, as to whether the tool is green with an electric cord having an outer surface that looks like the...
User Manual - Page 13
...The platen can sand a single angle. Figure 12 Figure 13
13 If slight adjustment is set at 90° (perpendicular to confirm that the miter gauge is needed:
1.
Belt Platen
The belt ... knob.
2.
Tighten the screw to the desired position.
Be sure to re-install the platen to perform operations where support of the Miter Gauge
The miter gauge is flush with the square, and the...
User Manual - Page 15
... Removal
The aluminum disc can be easily removed if needed; Loosen the set screw firmly when the disc has been mounted. Re-install dust cover and table.
9. Unplug sander from the power source.
... non-flammable solvent that will dry film-free.
5. Rotate the disc until the set screw.
4. Abrasive Disc Replacement
1. To remove the disc table, remove the handles then tilt the disc table ...
User Manual - Page 16
... of metals.
Figure 17 demonstrates a basic method of your hands. Set the angle you should check the accuracy of operation using the scale...you wish to start -up to catch and fly out of your setup by sanding a piece of the motor housing. Belt and Disc Movement...and store in OFF position to stop the motor and make repairs before doing any finish sanding on the miter gauge.
16
Figure...
User Manual - Page 17
... of wood in order to position the block as close as a guide. Sand a bevel in tight areas with the platen removed.
See ...the table tilted.
• Sanding aluminum on the disc unit with your JET Sander. • Sharpening a wood chisel on the belt unit with ...as possible to the sanding belt and clamp the block to support the chisel and provide clearance for the chisel handle.
2. ...
User Manual - Page 18
... Do not get paste wax on the tables will allow us to comply may cause serious injury.
Replacement Parts
To order parts or reach our service department, call will help protect them from the electrical supply by pulling out the plug or switching off... commercial detergent (or use 000 steel wool with grease and sealed at the factory. Having the Model Number and Serial Number of rust.
User Manual - Page 21
... Guard 1 47 41002-47 Handle 3 48 J-41002-48 Right Trunnion 1 49 J-41002-49 Disc Guard 1 50 TS-1540061 Hex Nut M8 4 51 41002-51 Aluminum Disc 8 1 52 6291479 Key 5x5x30mm 1 53 5640211 Abrasive Disc, 100 grit 8 1 54 41002-54 Dust Chute 1 55 J-41002-55 Left Trunnion 1 56 TS-1523011 Socket Set Screw M6x6 1
21 Parts List
Index No...
User Manual - Page 22
...-152704 Hex Wrench 3mmx140L 1 92 TS-0680031 Flat Washer 5/16 4 93 41002-93 Pan Head Screw 10-24x1/4 3 94 41002-94 Serrated Washer M5 1 95 41002-95 Cable 18# 100m/m 1 96 41002-96 Terminal A-3 1 97 41002-97 Cable 22# 200m/m 1 98 TS-0267041 Socket Set Screw 1/4-20x3/8 1 99 TS-1550031 Flat Washer M5 1 100........... TS-0680022...
JET Tools J-41002 Reviews
We have not received any reviews for JET Tools yet.