JET Tools JAT-405 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JAT-405 manuals!
Problems with JET Tools JAT-405?
Ask a Question
Free JET Tools JAT-405 manuals!
Problems with JET Tools JAT-405?
Ask a Question
Popular JET Tools JAT-405 Manual Pages
User Manual - Page 1
Pneumatic Angled Die Grinder
#505405, JAT-405 #505406, JAT-406
JAT-406
JAT-405
Operation & Parts Manual
M-505405 Edition 2 06/2015
JET 427 New Sanford Road
LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com
Copyright © 2015 JET
User Manual - Page 2
...Service
JET warrants every product it sells against manufacturer's defects. Please note that you specific legal rights, subject to the JET brand.
2 JAT-405,406 Angled Die Grinders Manual Hoist Accessories; Warehouse & Dock products; Air Tools
NOTE: JET...failures due directly or indirectly to Get Technical Support Please contact Technical Service by a 90 day limited warranty against ...
User Manual - Page 3
... defects or other purposes, JET disclaims any real or implied warranty and holds itself harmless from chemically treated lumber. Confine long hair.
16. Repair or replace damaged air hose immediately. ... floor strips are specifically designed to comply with approved safety equipment, such as face or dust masks that are recommended.
15. Never start a percussion type air tool (chipper, breaker,...
User Manual - Page 4
...fatigue.
29. Do not use power tools in minor injury and/or possible tool damage.
4 JAT-405,406 Angled Die Grinders If you are ... of the air tool into collet and collet nut is designed for the collet size of this manual:
fatal, injury...kerosene, diesel or jet fuel.
34.
Do not dispose of die grinder. 20. Give your hand.
39. Specific warnings for best...
User Manual - Page 5
... for quick access. If the tool transfers ownership, the manual should be reached at our web site: www.jettools.com. The instructions and warnings in this document. As with the instructions set forth in this manual for a JET Model JAT-405 and JAT-406 Pneumatic Angled Die Grinder. JET can also be first priority. This manual contains instructions on the cover of operator and...
User Manual - Page 6
... at any time and without prior notice, without incurring obligations.
6 JAT-405,406 Angled Die Grinders As workplace conditions vary, this information is intended to allow the user to change specifications at time of publication, but because of our policy of continuous improvement, JET reserves the right to make a better estimation of angle Collet...
User Manual - Page 7
.... Disconnect air. However, should the tool require future servicing, a grease fitting is available at low throttle without load for a few seconds to your JET® distributor. Use Lithium Complex Moly 2 grease or equivalent.
Setup and Assembly
Any missing parts or damage should be done with an in-line oiler, or manually. See "Lubrication" section.
Remove protective...
User Manual - Page 8
... dry air at a specialized facility.
8 JAT-405,406 Angled Die Grinders Air-line pressure may enter the tool and cause damage.
5. Use safety shut-...specifications, the following are not used for the job.
• Poor maintenance practices, such as SAE #10.
Inside diameter of a line break. Use anti-whip devices across hose couplings to serve the working area. Set tool to tool specifications...
User Manual - Page 10
...Flush tool with gum solvent. For problems not addressed below, contact JET technical service at air inlet, o-rings, etc. erratic action. Air valve obstructed or damaged. Improper lubrication. Disassemble and inspect bearing. Problem
Possible cause
Remedy
Tool will not start.
Open valve;
Replace vanes (entire set air pressure to instructions in this manual.
10 JAT-405,406...
User Manual - Page 11
JET 11 To order parts or reach our service department, call , so that we may serve you call 1-800274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Please have the stock number and serial number of your tool available when you quickly and accurately. Replacement parts
Service parts are listed on the following pages.
User Manual - Page 13
...
1
20 BB-608ZZ Ball bearing 608ZZ
3
46 JSM5252-46 Washer
1
21 JSM5252-21 Spring pin 2x15L
1
51 JSM5252-51 Damping material
1
22 52222
Pinion gear
1
JAT405-RPK, Repair Kit, contains 7(3),8,9,11,16(4),35,46 JAT405-RBK, Rebuild Kit, contains 18,24,25
JET 13 Description
Qty Index Part No. #505405, JAT-405, Right Angled Die Grinder -
User Manual - Page 15
parts list
Index Part No.
Description
Qty
1 JAT405-01 Motor housing
1
24 51224
Collet 1/4in.
1
2 40337
Lever pin 3x18L
1
25 ...JSM5252-51 Damping material
1
23 JSM5252-23 Front coupling
1
JAT406-RPK, Repair Kit, contains 7(3),8,9,11,16(4),35,46 JAT405-RBK, Rebuild Kit, contains 18,24,25
JET 15 Description
Qty Index Part No.
#505406, JAT-406, 115° Angled Die Grinder -
JET Tools JAT-405 Reviews
We have not received any reviews for JET Tools yet.