Pioneer GM-D9500F Support Question
Pioneer GM-D9500F Support Question
Find answers below for this question about Pioneer GM-D9500F.Need a Pioneer GM-D9500F manual? We have 1 online manual for this item!
Question posted by Liamg on September 2nd, 2017
Speakers And Sub Cutting Out
hi just wondering if you could help I have the GM D9500F amp and when I turn the volume up the front speakers and sub are cutting out? I have the rear speakers running off the head unit there fine and the front speakers and sub running off the amp, it's been good for a few years and help would be appreciated thank
Current Answers
Related Pioneer GM-D9500F Manual Pages
Owner's Manual - Page 2
... After-sales service for Pioneer products 3 Visit our website 3 Before connecting/installing the amplifier 4 Setting the Unit What's what 5 Setting gain properly 5 Connecting the units Connection diagram 7 Before connecting the amplifier 7 About bridged mode 8 About suitable specification of speaker 8 Connecting the speakers 8 Connections when using the RCA input
jack 10 Connections when using the...
Owner's Manual - Page 3
... insurance claim such as loss or theft. 2 Receive updates on file to help you refer to operate the equipment. After-sales service for Pioneer products
Please contact the dealer or... is designed to the companies at the following site: http://www.pioneerelectronics.com 1 Register your unit to give you many years of enjoyment. Before you start
Section
01
English
Thank you for after...
Owner's Manual - Page 4
The use of the car stereo while the en- This unit is at rest or idling may also heat up and cause minor burns.
! When installing this unit, smoke, and overheating could result from contact with liquids. Always install the amplifier on the bottom of any attached speakers may exhaust the battery. Electrical shock could cause malfunction...
Owner's Manual - Page 5
... output is restored when the volume of the head unit is connected:
Select LPF. When outputting high volume sound etc., this function cuts off frequency selectable from 40 Hz to 500 Hz if the LPF/HPF select switch is turned up, turn these controls to the same position. ! When the full range speaker is the NORMAL position. Protective...
Owner's Manual - Page 6
Despite correct volume and gain settings, the unit sound still cuts out periodically. Relationship between amplifier gain and head unit output power
If amplifier gain is raised improperly, this unit
Signal waveform when outputting at a high volume, set amplifier gain control to a level appropriate for the preout maximum output level of the gain control. In such cases, please contact the ...
Owner's Manual - Page 7
... metal parts in adhesive tape. ! Never wire the speaker negative cable directly-
If the car stereo lacks a system remote control terminal, connect the male terminal to ground. To protect the wiring, wrap sections in contact with cable clamps or adhe- Never cut the insulation of the car stereo. Never shorten any wires, the protection circuit
may...
Owner's Manual - Page 8
...-channel amplifier, with the ignition whether the car stereo is at rest or idling.
! Connect the speaker leads based on or off, which may result in parallel for two-channel and other bridge connections. Never band together multiple speaker'snegative cables.
! For other amplifiers, please follow the speaker output connection diagram for bridging shown on rear: two 8 W speakers in...
Owner's Manual - Page 9
Connecting the units
Four-channel output
Section
03
Two-channel output (Stereo)
English
1 Left 2 Right 3 Speaker out A 4 Speaker out B
Three-channel output
1 Speaker (Left) 2 Speaker (Right)
Two-channel output (Mono)
1 Left 2 Right 3 Speaker out A 4 Speaker out B (Mono)
1 Speaker (Mono) En 9
Owner's Manual - Page 10
... (RCA output), connect the plug to the amplifier using the RCA input jack
Connect the car stereo RCA output jack and the RCA input jack of the amplifier. ! Two-channel output (Stereo) / (Mono) ! Section
03 Connecting the units
Connections when using the supplied speaker input wire with RCA pin cord.
1 Car Stereo 2 Speaker output 3 Red: Right + 4 Black: Right * 5 Black: Left...
Owner's Manual - Page 11
... the car stereo, not the amplifier.
! Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car body.
3 Attach lugs to wires. After completing all amplifiers via the system remote control wire.
! If speaker wires with an RCA pin cord from a headunit are to be connected together synchronously, connect the head unit...
Owner's Manual - Page 12
... terminals
2 Attach lugs to wires.
12 En Connecting the speaker output terminals
1 Expose the end of the speaker wires using nippers or a cutter by about 10 mm (3/8 in.) and twist. Section
03 Connecting the units
1 System remote control terminal 2 GND terminal 3 Power terminal 4 Terminal screws 5 Battery wire 6 Ground wire 7 System remote control wire...
Owner's Manual - Page 13
... installation holes are to install the amplifier, always confirm no parts are behind the panel and protect all cables away from being cut by vibration of supplied tapping screws ...
Section
04
English
Before installing the amplifier
WARNING !
Do not cover the amplifier with the use unauthorized parts as a result of installation on the car model. fier, ensure the following during...
Owner's Manual - Page 14
Use this unit when an audio signal is nearly the maxi- The average current drawn is input.
mum current drawn by this value when working out total current drawn by multiple power amplifiers.
14 En Appendix
... Cut off frequency 40 Hz to 500 Hz Cut off slope 12 dB/oct High pass filter: Cut off frequency 40 Hz to 500 Hz Cut off slope 12 dB/oct Gain control: RCA 200 mV to 6.5 V Speaker ...
Similar Questions
Powering Up A Gm-a5602 Amp
The amp and Subs were working fine for a couple of months and then one day the blue power light woul...
The amp and Subs were working fine for a couple of months and then one day the blue power light woul...
(Posted by Mayojd74 6 years ago)
If You Are Using A Pioneer Gm-5500t Amp With A Single Channel Input Will It Run
full power mono?
full power mono?
(Posted by Chanpjkae 9 years ago)
How To Find Out Whats Stoping My Pioneer Gm-100t Amp
cant git any sound from pioneer GM-5100T amplifier to sub
cant git any sound from pioneer GM-5100T amplifier to sub
(Posted by davidriggs 13 years ago)