Pioneer GM-5500T Support Question
Pioneer GM-5500T Support Question
Find answers below for this question about Pioneer GM-5500T.Need a Pioneer GM-5500T manual? We have 1 online manual for this item!
Question posted by Anonymous-65926 on July 9th, 2012
Overheating
how do i fix my amp from overheating and cutting out?
Current Answers
Related Pioneer GM-5500T Manual Pages
Owner's Manual - Page 3
... removed (screws etc.) when installing the unit in overheating and smoke, damage to this number on this unit to the car body.
! This unit is recommended. Always disconnect ...the car stereo while the en- Always keep the volume low enough to prevent equipment malfunction. Extended use the parts you start
Section
01
English
Before connecting/ installing the amplifier
WARNING
...
Owner's Manual - Page 4
... function cuts off frequency selectable from 0 dB, 6 dB and 12 dB.
4 GAIN (gain) control If output remains low, even when the car stereo volume is turned up to indicate power ON. To ensure continuous sound output with max. For use with an RCA equipped Pioneer car stereo, with the head unit at a high volume, set amplifier...
Owner's Manual - Page 5
Signal waveform when outputting at high volume using amplifier gain control
Signal waveform distorted with little increase in power.
English
Section
02
En 5 Setting the unit
Relationship between amplifier gain and head unit output power
If amplifier gain is raised improperly, this will simply increase distortion, with high output, if you raise the gain...
Owner's Manual - Page 6
... (use a connector in adhesive tape. !
Before connecting the amplifier
WARNING ! Never cut the insulation of the amplifier is on page 8. Never ground speaker wire directly or band ...sections in contact with the ignition whether the car stereo is connected to other amplifier connections, finally connect the battery wire terminal of the amplifier to the positive (+) battery terminal.
2 ...
Owner's Manual - Page 7
...-channel (stereo) or one-channel (mono). About suitable specification of fire, smoke or damage. Speaker impedance is 2 W to 8 W for stereo connection, or...amplifier may result in parallel, Left + and Right * (Diagram A) or use a single 4 W speaker. For any further enquiries, contact your local authorized Pioneer dealer or customer service.
Improper connection to burns from overheating...
Owner's Manual - Page 8
... input wire
Connect the car stereo speaker output wires to the terminal.
Twist
Connecting the power terminal
The use of overheating, malfunction and injury, including minor burns.
1 Route battery wire from engine compartment to the vehicle interior. Fix the wires securely with the terminal screws.
8 En
After completing all other amplifier connections, finally connect the...
Owner's Manual - Page 9
Twist
1 Lug (sold separately) 2 Speaker wire 3 Connect the speaker wires to wire ends. Fix the speaker wires securely with the terminal screws.
1 Terminal screws 2 Speaker wires 3 Speaker output terminals
2 Attach lugs to the speaker output terminals.
En 9
Use pliers, ...
Owner's Manual - Page 10
...equipment (e.
When drilling to install the amplifier, always confirm no parts are to a certain designated temperature. ! fuel/brake lines, wiring) from being cut by vibration of a person in locations... the legs of the car, which can be dissipated, continuous use the supplied
parts in : - Heat may activate to protect the
amplifier against overheating due to prevent wires from...
Owner's Manual - Page 11
...8806; 1 % THD+N)
S/N ratio 78 dBA (reference: 1 W into 4 W)
Notes ! mum current drawn by multiple power amplifiers.
Use this value when working out total current drawn by this unit when an audio signal is nearly the maxi- The average current...) Distortion 0.05 % (10 W, 1 kHz) Low pass filter: Cut off frequency 40 Hz to 500 Hz Cut off slope 12 dB/oct Bass boost: Frequency 50 Hz Level 0 ...
Similar Questions
Amp Impedence
was wondering how you would ever run the pioneer gm-xgm-x542 2 channel amp at a 1ohm load and if you...
was wondering how you would ever run the pioneer gm-xgm-x542 2 channel amp at a 1ohm load and if you...
(Posted by truckss415 2 years ago)
My Pioneer Gm-5500t Audio Inputs Are Not Working Help
My amplifier inputs are not working because I screwed up and took it apart to clean the inputs becau...
My amplifier inputs are not working because I screwed up and took it apart to clean the inputs becau...
(Posted by jddubray 4 years ago)
Pioneer Gm- X924
how many watt is the pionner gm-x924? i want to buy two speacers for him
how many watt is the pionner gm-x924? i want to buy two speacers for him
(Posted by johnnymd98 10 years ago)
Gm-5500t 820 Watt Amp....not Turning On Even With Everything Connected Properly?
(Posted by coolmikepwnsu 12 years ago)