Pioneer GM-5500T Support Question
Pioneer GM-5500T Support Question
Find answers below for this question about Pioneer GM-5500T.Need a Pioneer GM-5500T manual? We have 1 online manual for this item!
Question posted by Dennisoquain2 on November 23rd, 2014
I Have A Gm 5500 T And It Was Working Fine Few Weeks I Lost Power How Ever If I
if i tap the power terminal lightly it powers up then back off where should i look at for the problem
Current Answers
Related Pioneer GM-5500T Manual Pages
Owner's Manual - Page 3
...amplifier and any abnormality, the power supply to prevent equipment malfunction. Electrical shock could result in overheating and smoke, damage to the product and injury, including burns.
! The surfaces of the car stereo... of an improper fuse could result. If the temperature inside the amplifier gets too
high. ! put terminal. If you to chemicals listed on this unit to the illustration ...
Owner's Manual - Page 4
...hear too much noise when using the speaker input terminals, turn the gain control to higher level.
5 Power indicator The power indicator lights up , turn controls to lower level. When the...LPF select switch is set amplifier gain control to a level appropriate for a few seconds as a normal function, but output is turned down.
! If distortion occurs when the car stereo volume is connected: Select...
Owner's Manual - Page 5
Setting the unit
Relationship between amplifier gain and head unit output power
If amplifier gain is raised improperly, this will simply increase distortion, with high output, if you raise the gain of the amplifier the power changes only slightly. English
Section
02
En 5
Signal waveform when outputting at high volume using amplifier gain control
Signal waveform distorted...
Owner's Manual - Page 6
... connection instructions. Before connecting the amplifier
WARNING !
Never cut the insulation of the power supply to feed power to other amplifier connections, finally connect the battery wire terminal of the wire is at rest or idling. !
If the car stereo lacks a system remote control terminal, connect the male terminal to metal body or chassis.
3 Car stereo with RCA output jacks (sold...
Owner's Manual - Page 7
...to the following standards, otherwise there is 2 W to 8 W for stereo connection, or 4 W to 8 W for monaural and other amplifiers, please follow the speaker output connection diagram for a 4 W load or a ... to the amplifier may result in malfunction or personal injury due to the figures shown below. Subwoofer
Speaker channel Two-channel output One-channel output
Power
Nominal input:...
Owner's Manual - Page 8
....
8 En
Use pliers, etc., to crimp lugs to the terminal. of the amplifier to the amplifier using the supplied speaker input wire. ! Section
03 Connecting the units
Connections when using the speaker input wire
Connect the car stereo speaker output wires to the positive (+) battery terminal.
1 Car Stereo 2 Speaker output 3 White/black: Left * 4 White: Left + 5 Gray/black: Right...
Owner's Manual - Page 9
... (3/8 in.) of wire and then twist the wire. En 9 Connecting the units
Section
03
English
1 System remote control terminal 2 Ground terminal 3 Power terminal 4 Terminal screws 5 Battery wire 6 Ground wire 7 System remote control wire
Connecting the speaker output terminals
1 Use wire cutters or a utility knife to strip the end of the speaker wires to the speaker output...
Owner's Manual - Page 10
... wires from damage. Insert the supplied tapping screws (4 mm × 18 mm) into the screw holes and push on the chassis. 3 Install the amplifier with the dri- To ensure proper installation...wiring) from being cut by vibration of the car, which can be dissipated, continuous use the supplied
parts in front of supplied tapping screws (4 mm × 18 mm).
1 Tapping-screws (4 mm × 18 mm) 2 ...
Owner's Manual - Page 11
... current drawn by multiple power amplifiers.
Additional information
Appendix
English
Specifications
Power source 14.4 V DC (10.8 V to 15.1 V allowable)
Grounding system Negative type Current consumption 29 A (at continuous power,
4 W) Average current... 0.8 V to
modifications without notice. ! Use this value when working out total current drawn by this unit when an audio signal is...
Similar Questions
My Pioneer Gm-5500t Audio Inputs Are Not Working Help
My amplifier inputs are not working because I screwed up and took it apart to clean the inputs becau...
My amplifier inputs are not working because I screwed up and took it apart to clean the inputs becau...
(Posted by jddubray 4 years ago)
Powering Up A Gm-a5602 Amp
The amp and Subs were working fine for a couple of months and then one day the blue power light woul...
The amp and Subs were working fine for a couple of months and then one day the blue power light woul...
(Posted by Mayojd74 6 years ago)
Power Light Flashing
My power light is flashing. It was working fine and now it doesnt i checked the connections, they se...
My power light is flashing. It was working fine and now it doesnt i checked the connections, they se...
(Posted by ntl1993 12 years ago)