Pfaff Varimatic 6091 Support Question
Pfaff Varimatic 6091 Support Question
Find answers below for this question about Pfaff Varimatic 6091.Need a Pfaff Varimatic 6091 manual? We have 1 online manual for this item!
Question posted by Chelemquilter on September 20th, 2014
Presser Foot Doesnt Seat On The Needle Plate When I Lower The Presser Bar Lifter
When I lower the presser bar lifter, the rod holding the foot takes a long time to decend and then does not firmly sit on the needle plate. So, the fabric does not move properly when stitching because there is not good contact with the feeddogs.
Current Answers
Related Pfaff Varimatic 6091 Manual Pages
Owner's Manual - Page 6
Lift off the cover and fold down the carrying handle. Take foot control and instruction book Out of compartment P. De voetpedaal en de gebruiksaanwijzing ...und den Tragegriff umklappen.
So wie die Abbildung oben zeigt, beides wieder einräumen. De koffer van de machine nemen en de handgreep achterwaarts kantelen. Enlever le couvercle de Ia valisette et rabattre a poignée.
Retirer le...
Owner's Manual - Page 8
... herausnehmen.
Raise latch P and pull out the bobbin case.
Release latch P and take out the bobbin. Klepje P oslaten, dan valt de spoel eruit Klappe P anheben und... for bobbin winding: Lift detachable work support and remove it. Open free arm cover 19.
a • Mettre Ia machine hors circuit I'm
terrupteur gdnéral 8. Lever le loquet P
et retirer a boite a canette.
• De ...
Owner's Manual - Page 15
Accessoiresbox in
terrupteur general 8. To insert extrathick fabric plies raise lever 15.
Werkstuk onder de naai voet leggen.
Hauptschalter einschalten.
Is het werkstuk erg dik, dan stofaan drukker 1 5 hoger duwen. Stoffdrückerhebel 15 senken,
Switch on master switch, Lower presser bar lifter 1 5.
Descendre le levier 1 5. Stoff unter den NhhfuB legen. • Switch off ...
Owner's Manual - Page 19
...u de stand van steeklengtewiel voor het naaien van stretchsteken.
Regulating the stitch length The numbers on stitch length control 9 indicate the stitch length in mm aan.
La longueur du point est reglable entre 0...Der Einstellbereich st 0 bis 6 mm. Turn the control to set the stitch length control for sewing the stretch stitches.
La longueur de point choisie est mdi quée face au rep...
Owner's Manual - Page 25
... 0 (sewing position). le déplacer vers 0 pour Ia couture. Schraube N lösen. Take out the needle. Lowering the feed dog Open free arm cover 1 9. Remplacement de laiguille (système
• 130/705 H): Mettre Is machine hors
circuità linterrupteur gdndral 8. Schroef N Iosdraaien. Schroef A vastdraaien,
Transporteur versenken Klappe 19 hffnen. Changing the needle...
Owner's Manual - Page 52
...90
130/705 H-M 60-90
--
e knitte- Coars- Medium ball point
i Heavy -
Sharp
For processing of microfibers. 01 /19/2(J08 Using the correct needle ensures better results.
Fabric weight: light
Needle size 60 70 75
Needle points
System and No.
d fabrics, Lastex, double- ball point
Stretch fabric needle. Light ball point Seams topstitched with
plastic sheeting and oilcloth.
Owner's Manual - Page 53
...
Mediumwide cording
Wide cording Extra wide cording Extra wide cording
Decorative designs sewn with twin needles
Before you start sewing, turn the handwheel and check to make sure the needles stitch into the fabric properly.
Heavily dressed fabrics are par ticularly suitable.
Stitch length
1
• 130/705 HZWl 2.5mm
80
2.5 mm
130/705 H-ZWI
80
2.5 mm
•
90...
Owner's Manual - Page 60
... fully upwards. Needle bent and strikes needle plate because fabric is not uniform Tension out of fabric. Check upper and lower tensions. Check threading. See par agraph 1 above reasons. Needle too small for thread used . Thread too thick, knotty or hard. Thread machine properly and check both tensions. Use topquality thread only, During bobbin winding, do not hold thread in...
Owner's Manual - Page 61
...
Lint has accumulated between tooth rows of feed dog. Machine feeds irregularly or not at right.l
Set feed-lowering control to switch off master switch 8. Remove needle plate and clean out lint.
01/29/2008
Cause:
Remedy:
5. Remove thread ends and put a drop of fabric under the sewing foot. Machine runs with difficulty Thread ends in hook raceway.
Owner's Manual - Page 68
...-91
Important) Only for Duel Feed)
98-694823-00 For hemming edges
Knit edge foot
93-042957-91
For sewing knitted fabrics For sewino plastic,
Straight stitch needle plate with round needle hole
- Single-needle cording foot
93-036915-91 For single-needle cording
Eyelet plate
93-036976-45 For eyelet embroidery
Roll hemmer 2mm
98-694873-00 For hemming edges...
Owner's Manual - Page 69
...
19, 20
13
.
26, 27
9
.
25
38, 39 Notes on buttons
Sewing straight stitches
Special accessories
Stitch pattern knob .
Operating the foot control
Presser bar lifter
.
Checking the bobbin thrpad tension
Checking the needle thread tension
Cleaning and oiling
Darning w th straight stitches
Ddrning with wool
. Reverse sewing
Safety rules lUnited Kingdom onlyl
Setting the...
Similar Questions
I'm Trying To Make A Button Hole, The Sewing Machine Is Not Advancing The Fabric
(Posted by paulinegp22 4 years ago)
Presser Bar Lifter.
The presser bar lifter moves up and down but the sewing foot does not lower onto the fabric.
The presser bar lifter moves up and down but the sewing foot does not lower onto the fabric.
(Posted by hemamohan6 4 years ago)
Pfaff 259 Sewing Machine Won't Run With Foot Petal
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
(Posted by Aemazing 8 years ago)
