Pfaff Tipmatic 1027 Support Question
Pfaff Tipmatic 1027 Support Question
Find answers below for this question about Pfaff Tipmatic 1027.Need a Pfaff Tipmatic 1027 manual? We have 1 online manual for this item!
Question posted by joannekulesza on July 15th, 2015
Tipmatic 1027 Has Power, The Light Is On , But It Won't Run.
Plugged in. Light on. no movement when foot pedal depressed. fly wheel turns. needle rises and falls
Current Answers
Answer #1: Posted by TommyKervz on July 16th, 2015 12:10 PM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,833
Member since:
January 10th, 2013 Points: 17,776,833
Make sure that the belt is attached to the motor.
Make sure that the needle is not loose not stuck in the hook' if so remove the needle and install a new one.
I find the info on the link below to be helpful in your case.
http://www.ebay.com/gds/HOW-TO-FIX-YOUR-SEWING-MACHINE-IN-5-EASY-STEPS-/10000000004629782/g.html
Related Pfaff Tipmatic 1027 Manual Pages
Owner's Manual - Page 2
...and accessory compartment Electrical connection Foot control Placing spool of thread on pin Upper threading Threading the needle Disengaging the sewing mechanism Bobbin winding Removing ... 1027 Selecting the needle position for straight stitching
Droppingthemachinefeed Changing the needle
Changingthesewingfoot Special sewing feet Buttonhole settings Sewing buttonholes
Sewing feet Changing the light ...
Owner's Manual - Page 4
... the needle when sewing. b) Make sure you unplug the power cord whenever you want to change the needle, sewing foot, bobbin or needle plate, when you want to clean and oil the machine or have to interrupt sewing and leave the machine for entering phone number of customer service
a) Be careful to use only a 15-watt light bulb in the sewing lamp...
Owner's Manual - Page 5
On Model 1027 a stitch chart is found on the inside of this cover (A).
Removing and opening the swing-out arm Reach under the swing-out arm with your ...
Owner's Manual - Page 6
Accessory box and accessory compartment sTliofiltrtyitucpooutmht ep(Aaf)rr.tomTnhet enortfe(aBics)caeunsnsdaoedrrdynietbiaootnxha.4l 6acacneds
Ill.
I;- C shows how the second spool holder
snap-on sewing feet, the and the seam ripper fit
into the box. C
a
0
0 C
2
.
Owner's Manual - Page 7
... plug B into the machine socket and plug C into the wall outlet. Your machine is placed in the machine again as shown in the illustration (A). Press down the pedal, and the machine starts sewing. When you put the machine away, the foot control is now readyfor sewing. The more the pedal is depressed, the faster the machine runs.
3
Press master switch 34. Foot control
Place the foot...
Owner's Manual - Page 8
... guide 50 and into slot Ato the left .
4 For two-needle sewing, draw one thread into the right thread guide Don the needle holder. C Second spool holder:
This is contained in the accessory ...Insert the spool holder in hole F and place a spooi of thread.
Upper threading Raise the sewing foot. Placing spool of thread on pin A Small spools of thread:
Push unreeling disc Don the spool...
Owner's Manual - Page 9
After bobbin winding, tighten the knob again by turning it away from front to back. V
Disengaging the sewing mechanism Before you .
5
Threading the needle Thread the needle from you start winding the bobbin, disen gage the sewing mechanism. Hold the hand wheel steady and turn the stop motion knob toward you.
Owner's Manual - Page 10
... slot D. Draw the needle thread under the sewing foot, up and into slot 54, and from a second spool (A)
Disengage the sewing mechanism. Then wind a few times and push the bobbin toward the left and take it around bobbin tension stud 55. Winding the bobbin from above around the bobbin a few turns of thread on the...
Owner's Manual - Page 12
... upagainandthetake-up lever is up. Release the latch and lightly press against the bobbin case to make sure it has snapped into
place. Drawing up the bobbin thread
Hold the needle thread a little taut. Turn hand wheel 32 toward the left and back under the sewing foot.
8
Inserting the bobbin case Pull out latch K and push...
Owner's Manual - Page 14
... slide down freely by its own weight, but should gradu ally move downwards when you jerk your hand upwards lightly.
4
4- The higher the number, the tighter the tension. Lower tension B = Regulating screw.
E
I
10 Turn it leftfora loosertension, or right for a tighter tension. E Lower tension too loose or upper tension too tight.
C = Both...
Owner's Manual - Page 15
... 44. B shows how to set the stitch length control for sewing stretch stitches (red stitch symbols on push buttons). As long as you keep this button depressed, the machine sews back wards.
11
Stitch length range: Model 1025: 0-4 Model 1027: 0-6 Ill. Regulating the stitch length Turn the control so that the number indi cating the stitch...
Owner's Manual - Page 16
Finger-tip controls of model 1027 10 Elastic triple straight stitch
Straight stitch 11 Pullover stitch
Blindstitch 1 2 Closed overlock stitch
Joining stitch 1 3 Overlock stitch
Shell-edge stitch 14 Feather stitch
Elastic ...
Owner's Manual - Page 18
Selecting utility stitches (white symbols) Push the desired button and turn the stitch length control as far as it will go (red symbol). Selecting stretch stitches
(red symbols) Push the desired button and turn the stitch length control to the number indicating the desired stitch length (1 -6 on model 1027, or 1-4 on model 1025).
Owner's Manual - Page 19
... sew an elastic blindstitch, push buttons 1 5 and 1 6, select a stitch length between 1 and 4. This stitch can also be sewn with model 1025.
and stretch-stitch combinations, model 1027
The various stitch combinations are shown in the chart on the inside of the hinged top cover. L ri J
6
L Selecting the needle position for straight stitching
Left needle...
Owner's Manual - Page 21
... slot C. Lower presser bar lifter 42 and at the same time reposition the sewing foot so that stud B fits in place with your left hand.
Screw F serves to secure the sewing foot holder on the presser bar.
17 Place the sewing foot under the sewing foot holder and hold it in slot C. Hole E and screw Dare used for...
Owner's Manual - Page 22
... the stitch length control (B). Regulate the stitch density in the buttonhole range of the foot, pull it taut and clamp it in position with screw H. Special sewing feet A Blindstitch foot
Blindstich guide E is adjusted by turning screw D. Attach the buttonhole foot. B Zipper foot First insert its rear pin into groove F, then push its front pin into...
Owner's Manual - Page 23
... keep it depressed
until the machine has sewn 4 to 6 bartacking stitches. Remove the fabric, pull the filler cord taut and trim.
6 Cut the buttonhole open.
4
19 Turn the hand wheel toward you to 6 bartacking stitches. Turn hand
wheel torward you until the machine has sewn 4 to raise the needle. 2 Push button 20 and keep it will go. 1 Sew first...
Owner's Manual - Page 25
... oiling Tilt needle plate 38 up at the back (A) and take it out (B). Clean the machine feed and the parts in slots C. Do not oil the machine because it is put a drop of the sewing hook with a sàft brush.
Push it up and turn it toward B. Changing the light bulb
Push the light bulb up, turn it...
Owner's Manual - Page 26
... knotty thread used, or thread that has become too dry by excessive storage.
3. Machine skips stitches Needle not inserted correctly. Needle bent and strikes needle plate because work alone.
Only guide the material lightly. Insert new needle. Select needle according to Needle and Thread Chart. Let machine feed the work is pushed or pulled. Trouble shooting
rCa use:
1. Insert...
Owner's Manual - Page 27
....)
Flick reverse-feed control to the right.
6. Remove needle plate and clean out lint. Feed dog dropped. (Reverse-feed control is not uniform Tension out of material.
Seam is at all
Lint has accumulated between tooth rows of oil into hook raceway.
23
Machine runs with difficulty Thread ends in hand, but pass...
Similar Questions
Pfaff 259 Sewing Machine Won't Run With Foot Petal
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
(Posted by Aemazing 8 years ago)
Pfaff Tipmatic 1027 -emitting Smoke
My Pfaff 1027, while not being used, started to emitt smoke from various openings. I unplugged and l...
My Pfaff 1027, while not being used, started to emitt smoke from various openings. I unplugged and l...
(Posted by Clingwood 9 years ago)
Pfaff Tipmatic 1027 Bobbin Winder
I cannot get the bobbin winder on Pfaff Tipmatic 1027 to run and wind the thread on. I have had to w...
I cannot get the bobbin winder on Pfaff Tipmatic 1027 to run and wind the thread on. I have had to w...
(Posted by gdhulbert 9 years ago)
No Power From Foot Pedal
I have a 1975 PFAFF Synchromatic machine. Works great, but I have had intermittent problems with lac...
I have a 1975 PFAFF Synchromatic machine. Works great, but I have had intermittent problems with lac...
(Posted by mlmcham 10 years ago)