Onkyo TX-8050 Support Question
Onkyo TX-8050 Support Question
Find answers below for this question about Onkyo TX-8050.Need a Onkyo TX-8050 manual? We have 1 online manual for this item!
Question posted by wijnhuis on September 15th, 2012
Automatic Standby
when my i-pod shuffle is connected in the usb-connection and in the ipod(std) mode afther half an hour or 40 min my tx-8050 goes automaticly into standby
Current Answers
Related Onkyo TX-8050 Manual Pages
Owner Manual - Page 1
Network Stereo Receiver
TX-8050
Instruction Manual
Contents
Introduction En-2
Connections En-10
Thank you to obtain optimum performance and listening enjoyment from your new Stereo Receiver. Please retain this manual for purchasing an Onkyo Network Stereo Receiver.
En-18
Appendix Troubleshooting En-51 Specifications En-54
En Please read this manual will enable you for future...
Owner Manual - Page 3
... used in a residential installation.
NOTE: This equipment has been tested and found to select Standby mode does not fully disconnect from the AC power source.
En-3
For U.S. AC Fuse-The ...measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and
receiver. • Connect the equipment into an outlet on the unit, contact your...
Owner Manual - Page 4
... nano, iPod shuffle, and iPod touch are trademarks of theMicrosoft group of iBiquity Digital Corporation.
For European Models
Declaration of the fuse. MIYAGI ONKYO EUROPE ELECTRONICS GmbH
Features
❑ Clean Design Aluminum Front Panel ❑ Network Capability
• Internet Radio • DLNA (Digital Living Network Alliance) ❑ iPod/iPhone*1 Digital Direct Connection via USB...
Owner Manual - Page 5
... 34 Server Requirements 34 USB Device Requirements 35 Supported Audio File Formats 35 About DLNA 35
iPod/iPhone Playback via Onkyo Dock ..........36 Using the Onkyo Dock 36 Controlling Your iPod/iPhone 37
Controlling Other Components 39
Advanced Setup 40 Changing the Advanced Setup Settings 40 Advanced Setup Menu 41
Zone 2 44 Connecting Zone 2 44 Zone 2 Out...
Owner Manual - Page 6
... * In catalogs and on packaging, the letter at the end of color. Remote control sensor
TX-8050
30°
30°
Approx. 5 m (16 ft.)
En-6 Aiming the Remote Controller
When using the remote controller, point it toward the receiver's remote control sensor, as possible to prevent damage from leakage or corrosion. • Expired...
Owner Manual - Page 7
... control (20) p BALANCE control (20) q MEMORY/MENU button (24) r TUNING MODE/ / button (23, 25, 51) s PRESET / button (24) t PRESET / button (24) u USB port (28) v RT/PTY/TP button (European model) (27)
En-7
Getting to Know the Receiver
Front Panel
North American model
a
234
5 678
9
jk l
m n o p qrst u
European...
Owner Manual - Page 8
...30, 31) j MUTING indicator (51) k Volume level (19) l USB indicator (28, 29) m SLEEP indicator (20, 41) n Audio input indicators
Display
abc 45
6
7
8
For detailed information, see the ...A terminals (10) r SPEAKERS B terminals (10)
See "Connecting the Receiver" for connection ( pages 10 to Know the Receiver-Continued
Rear Panel
a
b c4 5 6
7
8 9 jkl mno p
For ...
Owner Manual - Page 14
... can cause noise or malfunctions). Make sure that open when an optical plug is selected on TVs, VCRs, and other video equipment. Connecting Your Components
About AV Connections
Connecting AV components
Video Audio
Receiver
TV, projector, etc.
AV Cables and Jacks
Signal Cable Video Composite video
Jack
V
Yellow
Description
Composite video is commonly used on...
Owner Manual - Page 16
...Use only cables for connecting additional -capable components.
• Connect only Onkyo components to the receiver. The other jack is on a component connected via , while the receiver is on Standby, the receiver will automatically turn on and select that component as the input source.
■ Remote Control You can
connect either one to jacks. Refer...
Owner Manual - Page 17
... is output from your TV or playback VCR to the recording VCR without going through the receiver, connect the TV/VCR's audio and video outputs directly to make recordings, select another listening mode. Notes: • The receiver must be connected to a composite video output.
• Copy-protected Blu-ray discs and DVDs cannot be recorded.
•...
Owner Manual - Page 19
... are pressed or the receiver is on or off . • If you connect an iPod or iPhone to the USB port on the selected component.
4 To adjust the volume, use .
En-19 Notes: • Always turn down the volume before connecting your
headphones. • While the headphones plug is muted. Enjoying Audio Sources
SPEAKERS A, B
VOLUME
INPUT...
Owner Manual - Page 20
... when the sleep timer has been set the receiver so that if you press the [SLEEP] ...Audio Sources-Continued
DIMMER
MODE SLEEP
BASS
TREBLE BALANCE
Setting the Display Brightness
You can adjust the brightness of the left and right speaker systems. Note: If headphones are connected, the BALANCE control has no effect. Turn it turns off automatically after a specified period.
Select the Audio...
Owner Manual - Page 29
.... En-29 USB port
USB REPEAT
MODE U, J, I, Q, R, W, K RANDOM
&, (, ENTER
1 Press [USB] button to select the "USB" input.
2 Plug your important music files beforehand.
• MP3 players containing music files that you use to the receiver's USB port, we recommend that you back up your USB device into the receiver's USB port.
A list of the receiver, while the message "Connecting...
Owner Manual - Page 34
...server
Network Requirements
■ Ethernet Network For the best results, a 100 Base-TX switched Ethernet network is strongly recommended (e.g., cable modem, xDSL modem, etc). ... (Network Address Translation).
Network/USB Features
Connecting to the Network
The following diagram shows how you can connect the receiver to play its network settings automatically. Although it , or may...
Owner Manual - Page 36
...'s Alarm Clock function to automatically turn on your iPod/iPhone model
and generation. • Before selecting a different input source, stop iPod/
iPhone playback to prevent the receiver from the Apple web site.
Note: When a UP-A1 Dock with the dock. PORT UP-A1 UP-A1 Dock is connected, the power consumption on standby mode slightly increases.
■...
Owner Manual - Page 37
... playback. Notes: • Connect the RI Dock to the receiver with video playback or
when the alarm is on Standby, the receiver will automatically switch to the input to control other
accessories, iPod/iPhone playback detection may not work with an cable
( page 16). • Set the RI Dock's RI MODE switch to "HDD" or...
Owner Manual - Page 41
... "Auto Standby" is connected to "On", the receiver will be deleted. the docked iPod/iPhone model is not supported. • When the "UP-A1 Charge Mode" setting is not connected to the PORT selector.
2. In such conditions, the power consumption of the source you connect a component (such as a UP-A1 Dock with no audio and no operation for...
Owner Manual - Page 42
... mask address provided by routers, computers, the receiver, and other devices to configure the receiver's network settings manually.
What's DNS? For example, when you have connected your browser uses DNS to +10 dB in standby mode.
The output can be set to use DHCP to configure itself automatically by your router's DHCP server is disabled (you...
Owner Manual - Page 51
... pushed
in all audio connecting plugs are connected properly. • Make sure that the power cord is output from your radio presets and custom settings.
Power
Can't turn it on and, while holding down the [TUNING MODE] button, press the [ON/STANDBY] button. Make sure that PCM is selected on the receiver • Make sure...
Owner Manual - Page 53
... off when the Pure Audio mode
is selected, the functions don't work • To use , you must make sure that support the
USB mass storage device class.
Others
Standby Power Consumption • In the following cases, the power consumption may not always
allocate the same IP address to the receiver, so if you...
Similar Questions
Onkyo Av Receiver Tx-sr343 Firmware File
Where can I download the firmware file for Onkyo AV Receiver TX-SR343?
Where can I download the firmware file for Onkyo AV Receiver TX-SR343?
(Posted by kamalbul 1 year ago)
How Do I Hook Up An Onkyo Equalizer To My Onkyo Av Receiver Tx-sr600
how do I hook up my Onkyo equalizer to my Onkyo AV receiver TX-SR600
how do I hook up my Onkyo equalizer to my Onkyo AV receiver TX-SR600
(Posted by casesimmons94 3 years ago)
Meaning Display Message 'now Initialize'on Tx 8050 Reciever In Usb Mode. No More
i tried to play misuc in usb mode on my tx 8050 reciever and recieved the mesage 'now initialze'. si...
i tried to play misuc in usb mode on my tx 8050 reciever and recieved the mesage 'now initialze'. si...
(Posted by jefleunissen 10 years ago)