Makita SP6000J Support Question

Find answers below for this question about Makita SP6000J.
Need a Makita SP6000J manual? We have 4 online manuals for this item!

Makita Overview Questions Manuals Reviews Videos Research

Question posted by rlovell on January 17th, 2019

Sp6000

what the difference between the sp6000j and the sp6000k

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by BusterDoogen on January 17th, 2019 10:00 PM

This answer was accepted by the poster of the original question.

BusterDoogen

Member since:
October 30th, 2011

Points: 28,565,407

1,110
points

The same, the old number for the kit is SP6000K, new number is SP6000J1.

I hope this is helpful to you!

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!

Related Makita SP6000J Manual Pages

Owners Manual - Page 2

... power tool. Safety equipment such as pipes, radiators, ranges and refrigerators. This enables better control of electric shock. Keep your finger on . ENGLISH SPECIFICATIONS Model SP6000 Blade diameter... power tools to EPTA-Procedure 01/2003 GEA001-3 GENERAL SAFETY RULES WARNING! Water entering a power tool will reduce risk of inattention while operating power tools may differ from...

Owners Manual - Page 3

... less likely to minimize body exposure, blade binding, or loss of the power tool is dangerous and must be performed. The correct power tool will ensure that may contact hidden wiring or its own cord. Check for operations different from those intended could result in your hands or across your application. This will...

Owners Manual - Page 4

... kickback, do support board or panel near the edge of blade pinching and kickback. Investigate and take corrective actions to lift up or kickback from tool, then cleaning it may occur.

Owners Manual - Page 5

... 1 000194 • Never force the saw could easily jump backwards over your body under the tool base or behind the saw, especially when making cross-cuts. Check to make sure that guard ... at a speed so that the guard is extremely dangerous and can cause uneven cuts, loss of tool without slowing. 10. Use extra caution when cutting damp wood, pressure treated lumber, or wood containing...

Owners Manual - Page 6

... when use ) replace strict adherence to safety rules for the subject product. MISUSE or failure to 3 mm depth of cut . Quick stop button 007669 This tool has the quick stop button for 2 to follow the safety rules stated in this manual. Do not stop button for 2 to 3 mm first cut and...

Owners Manual - Page 7

... the left 1° bevel angle. For 45° bevel cuts, align the B position with the clamping screws. And then tilt the tool handle to the left 1 1. Base 2. When using the tool without guide rail (accessory) For straight cuts, align the A position on the workpiece. Bevel angle shifting lever Bevel cutting 1. Then, tilt...

Owners Manual - Page 8

...tool speed can be infinitely adjusted between 2,000 and 5,200 rotations per minute by turning the adjusting dial. lower speed is obtained when it past 6 or 1, or the speed adjusting function may differ... shock. ASSEMBLY CAUTION: • Always be reduced. Soft start feature Soft start the tool, push in the direction of number 1. To start because of workpiece. Speed adjusting dial...

Owners Manual - Page 9

To install hex wrench, place it on the tool. Lock-off button to change the dust bag position. 1. BE SURE TO TIGHTEN THE HEX BOLT CLOCKWISE SECURELY. 4 3 2...007662 Turn the locking lever to lock the saw blades which do not comply with teeth pointing up at the front of the tool. • Use only the Makita wrench to loosen the hex bolt counterclockwise. Dust port 2. To remove hex wrench, just ...

Owners Manual - Page 10

... until the blade attains full speed. Use both a front grip and rear handle. Turn on the tool, press down the saw head slowly to the preset depth of the dust as much of cut by...wait for blade to the cutting edge. Doing so may bind the blade and lead to move the tool forward over the workpiece surface, keeping it engages the undercut groove in the direction of your intended cut ...

Owners Manual - Page 11

...65439; 1 007667 11 MAINTENANCE 007686 WARNING: • To avoid a kickback, be sure that the tool is clamped on the front and the back of the saw head slowly to the preset depth of 90...° and 45° cut (vertical and 45° cut and simply move the tool forward to observe the following instructions. Rip fence (guide rule) (Accessory) 1. Plunge cutting (Cutting-out)...

Owners Manual - Page 12

... mark 1 001145 ACCESSORIES CAUTION: • These accessories or attachments are recommended for use accessory or attachment for more details regarding these accessories, ask your Makita tool specified in the holders. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. 1. Brush holder cap 1 2 007676 To...

Owners Manual - Page 13

... apply to state. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of original purchase. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, .... Some states do not allow the exclusion or limitation of normal wear and tear: the tool has been abused, misused or improperly maintained: alterations have been made to you . THIS...

Parts Breakdown - Page 4

WRENCH 5 1 A03 165447-6 SUB BASE 1 A03 824783-6 SYSTAINER 1 A04 804869-2 SP6000K PLASTIC CASE LABEL 1 90 631728-5 CONTROLLER 1 91 213261-5 O RING 17 1... 233089-5 COMPRESSION SPRING 12 1 99 265995-6 TAPPING SCREW 4X18 6 100 911273-9 PAN HEAD SCREW M5X50 1 101 862913-1 SP6000 NAME PLATE 1 102 188197-6 HANDLE SET 1 102 INC. 55 0 103 664265-4 POWER SUPPLY CORD AWG#16-2-2.5 1 ...

Flyer (English) - Page 1

... from wall PRECISION Depth stopper for Smooth Start-Ups • Large Cutting Capacity (2-3/16" at 90º and 1-9/16" at a depth of 1/16" ACCURACY Models SP6000J SP6000J1 (Includes 55" Guide Rail) Straight or bevel cutting; 6-1/2'' PLUNGE CIRCULAR SAW PRECISION ACCURATE CUTTING DELIVERS A SPLINTER-FREE MIRROR FINISH • Electronic Speed Control Maintains...

Flyer (English) - Page 2

... color is inserted Blade wrench through a hole attaches to the saw in the market Model SP6000J Model SP6000J1 0 88381 63900 2 0 88381 65082 3 STANDARD EQUIPMENT OPTIONAL ACCESSORIES n Carbide-tipped blade 48T (B-07353) n Hex blade wrench (783203-8) n Plastic tool case n 55" guide rail (194368-5 - SP6000J1 only) SPECIFICATIONS Blade diameter Arbor Max cutting capacities: 90...