Home » Makita » Tools » Makita 1902

Makita 1902 Support Question

Find answers below for this question about Makita 1902.
Need a Makita 1902 manual? We have 2 online manuals for this item!

Makita Overview Questions Manuals Reviews Videos Research

Question posted by tomartist2004 on October 19th, 2019

Cut Depth Know Is Stuck. Will Not Turn.

How can I get this knob to turn and work

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by hzplj9 on October 19th, 2019 10:45 PM

This answer was accepted by the poster of the original question.

hzplj9

Member since:
June 25th, 2012

Points: 4,873,500

1,100
points

if the knob is rusted and oil does not release it try using a mixture of brake fluid and acetone on the thread. Leave for time ( a few hours) then try again to release the adjuster. Use disposable gloves to protect your hands from the brake fluid. It is a well known mix to release stuck threads.

Hope that helps.

Answer #2: Posted by aleyn on October 19th, 2019 8:30 PM

aleyn

Member since:
October 19th, 2019

Points: 100

100
points

.try to pour some oil

Answer #3: Posted by waelsaidani1 on October 19th, 2019 9:04 PM

waelsaidani1

Member since:
May 12th, 2013

Points: 19,501,787

100
points

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation.

Related Makita 1902 Manual Pages

Owners Manual - Page 1

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. www.makitatools.com Power Planer MODEL 1902 DOUBLE INSULATION 002543 INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using.

Owners Manual - Page 2

.... Keep bystanders, children, and visitors away while operating a power tool. SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well lit. If it still does not fit,... the plug. Power tools create sparks which may ignite the dust or fumes. 3. SPECIFICATIONS Model Planing width Planing depth Shiplapping depth No load speed (RPM) Overall length Net weight 1902 82 mm (3-1/4") 1...

Owners Manual - Page 3

...tool serviced before turning the tool on the switch or plugging in moving parts, breakage of starting . Maintain tools with grounded surfaces such as pipes, radiators, ranges and refrigerators. Properly maintained tools with sharp cutting edges are less likely to carry the tools... and use tool if switch does not turn it is dangerous and must be repaired. 18. Holding the work by the ...

Owners Manual - Page 4

...heavier gage. Before using an extension cord, be left around the work area. Tool service must be suitable for a while. Use of unauthorized parts or failure to planer safety rules.... When using the tool on another tool. Use only sharp blades. SERVICE 23. Table 1: Minimum gage for and remove all nails from the workpiece before operation. 2. Avoid cutting nails. model. Be sure ...

Owners Manual - Page 5

... the blade is turned on. 9. Do not leave the tool running. When leaving the planer, switch off and wait for tool. Follow material supplier safety data. Operate the tool only when hand-held. 14. Use only Makita blades specified in this manual. 18. Some material contains chemicals which may jam when cutting damp wood. SAVE...

Owners Manual - Page 6

... push in the tool, always check to stop the tool from the locked position, pull the switch trigger fully, then release it. FUNCTIONAL DESCRIPTION CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the front of cut may be adjusted by simply turning the knob on the...

Owners Manual - Page 7

...heel of the adjusting plate into position. Mini planer blade 2. Remove the existing blade, if the tool has been in the three hex flange head bolts so that the blade ends are clear and equidistant... flank of the installation bolts. Drum • Use only the Makita wrench provided to ensure uniform cutting. 5. flange head bolt 5. Drum plate 6. Failure to do so may result in the blade ...

Owners Manual - Page 8

clearances between the blade ends and the tool body. 9. The blade must be mounted so that the cutting edge is absolutely level, that is set properly and securely. Below ... base line. For the correct planer blade setting Your planing surface will minimize chip scatter, making for a cleaner work area. 1 1. Cause: One or both blade edges (A) (B) protrudes too far in relation to the rear...

Owners Manual - Page 9

... be increased, while for a good finish you should reduce the depth of cut and advance the tool more slowly. 002580 Shiplapping (Rabbeting) To make a stepped cut as shown in the figure, use the edge fence (guide rule). 9 Chip cover screw 2. The speed and depth of finish. Planing will not result in jamming by chips. Then...

Owners Manual - Page 10

... fence flush with the side of the workpiece, then secure it comes in contact with the cutting line. 002583 Adjust the edge fence until it by attaching an extra piece of the tool. Maximum shiplapping (rabbeting) depth is 9 mm (11/32"). 2 002584 You may result. Insert the edge fence into the hole in...

Owners Manual - Page 11

... carbon brushes Remove and check the carbon brushes regularly. Both carbon brushes should be sure that the tool is switched off and unplugged before attempting to the limit mark. 003634 Chamfering To make a chamfering cut as shown in the figure, align the "V" groove in the holders. "V"groove MAINTENANCE CAUTION: • Always be...

Owners Manual - Page 12

... for its stated purpose. Brush holder cap 2. ACCESSORIES CAUTION: • These accessories or attachments are recommended for more details regarding these accessories, ask your Makita tool specified in this manual. Only use of injury to remove the brush holder caps. 1. If you need any other accessories or attachments might present a risk...

Owners Manual - Page 13

Cut Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 First-Class Postage Required Post Office will not deliver without proper postage. Fold 13

Owners Manual - Page 14

...: (714) 522-8133 Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( 3. SERIAL NO. Use of the product is intended for: Construction Trade Industrial Maintenance Home Maintenance Hobby Other ( ) 4. Most favored...

Owners Manual - Page 15

... Allis, WI 53227 (414) 541-4776 CUSTOMER'S RECORD When you need service: Send complete tool (prepaid) to one of the Makita Factory Service Centers listed, or to the outside of the carton detailing ...the problem with your tool. Pittsburgh, PA 15209 (412) 822-7370 PUERTO RICO 200 Guayama St. Decatur Blvd. Louis, MO...

Owners Manual - Page 16

...trouble develop during this type of work with approved safety equipment, such as those dust masks that are required because of normal wear and tear: • the tool has been abused, misused or... and tested before leaving the factory. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by defective workmanship or material, Makita will repair (or at our option, ...

Parts Breakdown - Page 2

...1902...BELT, 1902 V-PULLEY 4-38, HM0860C B. BOLT M6X17, 2030S BLADE GAUGE, 1902 SOCKET WRENCH..., 1902 P.H. SCREW M4X25, 5057KB V-PULLEY 4-18L, HM0860C BELT COVER, 1902 RUBBER... 1 6 1 1 1 2 1 1 1 1 2 2 4 1 6 1 1 2 2 1 4 Page 2 of 2 8/18/2010 SCREW M4X16, 1902 BAFFLE PLATE, N1900B CARBON BRUSH 76, 6905B CARBON BRUSH SET CB-76, 6905B BRUSH CAP , 9031 COMP. BEARING 608ZZ, N1900B DRUM, N1900B...