LiftMaster MT Support Question
LiftMaster MT Support Question
Find answers below for this question about LiftMaster MT.Need a LiftMaster MT manual? We have 2 online manuals for this item!
Current Answers
Answer #1: Posted by SonuKumar on January 31st, 2023 8:36 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,638,180
Member since:
May 9th, 2021 Points: 16,638,180
https://youtu.be/5KzJ2_2cYpk
To program a LiftMaster MT remote:
Locate the "Learn" button on the garage door opener unit, usually mounted near the motor.
Press and release the "Learn" button. The indicator light will glow steadily for 30 seconds.
Within the 30-second window, press and hold the button on the remote control you want to program until the indicator light blinks.
Release the button on the remote control. The opener will emit a buzzing sound, indicating successful programming.
Repeat steps 3-4 for additional remotes.
To finish, press the "Learn" button again to exit programming mode.
Note: The exact steps may vary slightly depending on the specific model of your LiftMaster MT opener. Please refer to the owner's manual for more detailed instructions.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related LiftMaster MT Manual Pages
MT5011E Installation Manual - Page 1
INSTALLATION MANUAL
MODEL MT5011E/BMT5011E
MEDIUM DUTY DOOR OPERATOR
RaNdoBiwuoiRlwteiitcnheiver
INTENDED FOR PROFESSIONAL INSTALLATION ONLY
Visit www.LiftMaster.com to locate a professional installing dealer in your area.
2 YEAR WARRANTY
Serial # (located on electrical box)
Installation Date
Radio Receiver Built on Board
315MHz
NOT FOR RESIDENTIAL USE
A SAFETY DEVICE IS HIGHLY RECOMMENDED.
MT5011E Installation Manual - Page 2
... will
AAVVEERRTTIISSSSEEMMEENNTT alert you to the possibility of damage to your door and/or the
door operator if you do not comply with the warnings that accompany it will...INSTALLATION 9-14 ADJUSTMENT 14-15 OPTIONAL SAFETY DEVICE CONFIGURATIONS 15-16 LOGIC BOARD LAYOUT 17 BASIC PROGRAMMING 18-20 TESTING 21 MANUAL DISCONNECT 21 TROUBLESHOOTING 22-23 DIAGRAM 23 REPAIR PARTS 24-26...
MT5011E Installation Manual - Page 4
... 115Vac, Single Phase, 60Hz FULL LOAD AMPS 6.0 Amps
ELECTRICAL
OPERATOR VOLTAGE 115 Vac, Single Phase, 60 Hz WIRING TYPE C2 Standard B2 configurable (see Basic
Programming section) CONTROL WIRING 16-22 AWG
MECHANICAL
DOOR SPEED 12" (30.48 cm) / second OUTPUT FORCE 125 ft.
MT5011E Installation Manual - Page 5
...Before beginning your installation check that all components were provided.
15 1
14
^
^OPEN
CLOSE
O
STOP
8
4
10 9
7
2 12
3
13 11
6 5
ITEM DESCRIPTION
QTY
1
Operator
1
2
Track (left & right)
Door height plus 2'
2
3
Track Spacers
2
4
Front Idler
1
5
Trolley
1
6
Take-up Bolt
1
7
Chain
1
8
Master Links
2
9
Header Bracket
1
10
Header Pivot Shaft
1
11
Curved...
MT5011E Installation Manual - Page 8
6 Install chain
Attach chain
to front of
trolley
Chain
Trolley
Master Link
ASSEMBLY
Track Front Idler
Wrap chain around front idler
Chain
Run chain around track in the direction indicated
Slide ...
Attach chain to back of trolley
Adjust the chain by tightening the inner nut
Trolley
Chain
Inner Nut Master Link
Bottom of
Track
3"
Chain
8
Bottom of Track
More than 3"
Chain
MT5011E Installation Manual - Page 11
...
Secure the operator using appropriate fasteners and locking hardware that will support the weight of the garage. CAUTION
To avoid possible SERIOUS INJURY from a falling operator, fasten it SECURELY to structural supports of the operator.
Vertical
NOTE: Refer to door (Not Provided).
Lock
Nut
Washer
Bolt (Not Provided)
Bolt (Not Provided)
7 Attach...
MT5011E Installation Manual - Page 13
... for 3-button control station
Remove cover
^OPEN Screws
CLOSE
O
STOP
Wall
Secure using appropriate hardware
5' (1.5 m)
3-Button Control Station
CAUTION
To prevent possible SEVERE INJURY or DEATH, install reversing sensors when: • The radio is used. • The 3-button control station is out of sight of the door. • Or ANY other control...
MT5011E Installation Manual - Page 14
... moving limit nuts or adjusting clutch nut. Depress retaining plate
Adjust OPEN limit
Retaining Plate OPEN Limit Nut OPEN Limit Switch CLOSE Limit Nut
AVERTISSEMENCLTOSE Limit Switch
ATTENTION
Increase Door Travel
Adjust CLOSE limit
Increase Door Travel Decrease Door Travel
AVERTISSEMENT
AVERTISSEMENT Decrease Door Travel
SAFETY Limit Switch
NOTE: When retaining plate is released, verify...
MT5011E Installation Manual - Page 15
... more than 6" (15 cm) above the floor. If an obstruction breaks the light beam while the door is closing , the door will stop and typically reverse to the full open position. Safety Edge
SENSING EDGES When properly connected, the sensing edge will make contact with cotter pin.
Remove Tape Holding Cotter Pin to...
MT5011E Installation Manual - Page 17
... Auxiliary Antenna Connection
LED
Field Wiring Terminal Factory Wiring Connector
FUNCTION Open Door Close Door Stop Door Programs the remote controls and performs additional programming Programs the Timer to Close Primary Antenna For use with external antenna kit EXT-ANT. Not Provided Used during programming and diagnosing error codes Field wiring connections Factory wiring harness connection...
MT5011E Installation Manual - Page 18
... to the following descriptions of the door. • Or ANY other control (automatic or manual) is based on the logic board will begin closing by any opening device.
• Wiring for Monitored...wiring types will go into a Restricted Close mode**. Electrical Box Logic Board
Photo Eye
TO PROGRAM Press and hold the LEARN and STOP buttons until the LED goes out (approximately 3 seconds...
MT5011E Installation Manual - Page 20
... TTC will use 3 of the STOP button. 5. Press and release the LEARN button (LED will light). 3.
TO PROGRAM
1. All programmed remote controls will go out). Requires LiftMaster monitored safety device. Open
Close Stop
2. Tested to exit programming mode. 6.
Press and hold the desired button of this device may cause undesired operation.
Press and hold the...
MT5011E Installation Manual - Page 21
... to disengage trolley ONLY when door is
installed. 4. Press STOP button. (The door should close . TEST THE SAFETY DEVICES (IF INSTALLED) 1. Door Arm
Lift free end of the limits. Press CLOSE button. (The door should close .
21 If the limits are installed.
The door
AVERTISSEMENT should move in the open the door only. 1. TEST REMOTE CONTROL * Requires B2 wiring...
MT5011E Installation Manual - Page 22
... CLOSE button for proper operation. NO RESPONSE
A) Remote control is not programmed
➤ See PROGRAMMING REMOTE CONTROLS section.
B) Brake not releasing (if present)
C) Door operation problem
OPERATOR MOVES IN OPEN and CLOSE button wiring THE WRONG DIRECTION connection reversed
DOOR DRIFTS AFTER OPERATOR STOPS
A) Door not balanced properly
➤ Verify brake assembly operation...
MT5011E Installation Manual - Page 23
Door height or speed may exceed the range the operator can be determined by counting the number of flashes of the operator can travel.
Brown** Brown**
Orange Purple
Yellow
Grey
Safety Limit Switch
Open Limit Switch
Grey
Close Limit Switch
23
AANTUX ANT
J2
TTC
LEARN STOP CLOSE OPEN LED
1
2
3
4
5
6
7
LMEP1 LMEP2 COM INTRLK...
MT5011E Installation Manual - Page 26
... and hardware. K72-33875 Clutch shaft kit
Complete with Master Link Brake Plate Pad Assembly Track for doors 8' to 10' Track for doors 10' to 12' Track for 14' doors #48 Chain for doors 8' to 10' #48 Chain for doors 10' to 12' #48 Chain for 14' doors
26 Push on fastener, 3/4", 1 part Chain, #48x33 Pitch with...
MT5011E Installation Manual - Page 27
...(500'): Color coded, white andOPwEN hite/black. OPEN
OPEN
ACCESSORIES
REMOTE CONTROLS 315MHz
ENTRAPMENT PROTECTION DEVICES
371LM
1-Button SECURITY✚® Remote Control:
Monitored
PRESS TO
Includes visor clip. CLOSE....)
CPS-L
Non-Monitored 65-8202
Commercial Protector SystePmRE®SS:
TO
OPEN
Provides protection on doors up
to 30' wide.
CLOSE
PRESS TO
R ING
50-104-1
...
MT5011E Installation Manual - Page 28
... is added to ensure proper installation and operation
with the Commercial Door Operator.
3 BUTTON STATION OR 3 POSITION KEYSWITCH WITH SPRING RETURN TO CENTER AND STOP BUTTON
STANDARD 7635
2 OR MORE 7635
KEY LOCKOUT 7635
Open Close Stop
Open Close Stop
Open Close Stop
Open
Close Stop
Keyswitch
2 BUTTON STATION OR 3 POSITION KEYSWITCH WITH SPRING RETURN...
MT5011E QuickStart Guide Manual - Page 1
...
TTC
open limit after a preset time, adjustable from 5 to complete programming (LED will flash once per 5 seconds of the 20 memory channels in your area.
Press and hold the LEARN button (over 5 seconds) until the LED goes out. All programmed remote controls will no longer be erased. The LED will go out). Begin with door...
MT5011E QuickStart Guide Manual - Page 2
... model MT/BMT door operator
IMPORTANT: This QuickStart is obstructed. These instructions are positioned between the limit switches before proceeding with the header bracket then secure the brackets to locate a professional installing dealer in the installation manual.
01-34216B
© 2008, The Chamberlain Group, Inc. Visit www.LiftMaster.com to the ceiling. OPEN...
Similar Questions
My Lift Master Mt-1211, 1/2 Hp
Will open from closed position but will not close when opened.Tried both remote and wall control. th...
Will open from closed position but will not close when opened.Tried both remote and wall control. th...
(Posted by patrickkaren86 6 years ago)
How Big Of A Garage Door Will A Model Mt 1211 Lift Weight And Width ?
I have a 13' wide 8' high door. Its a older heavy door. I have a new model MT 1211 I had for a 9' wi...
I have a 13' wide 8' high door. Its a older heavy door. I have a new model MT 1211 I had for a 9' wi...
(Posted by crusin31again 10 years ago)
How Much Does A Lift Master 3255 Garage Door Opener Cost
(Posted by cosin 10 years ago)
How Do You Remove 485lm Battery From Lift Master 3850p Garage Door Opener
(Posted by cmscalh 10 years ago)
Remote Door Opener
How do you reprogram a remote on a liftmaster model MT 5011
How do you reprogram a remote on a liftmaster model MT 5011
(Posted by khanlon 12 years ago)